Bedienungsanleitung Nec gt6000 (Seite 13 von 115) (Englisch)

216054

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

1-9

USB

(

MOUSE/HUB

)

USB

(

)

PC CARD

PC CONTROL

OUT

SC TRIGGER REMOTE 2

REMOTE 1

LAN

AC IN

12 3

10 11

1. USB Port [MOUSE/HUB] (Type A)

Connect a USB mouse. You can operate the menu or Viewer

with a USB mouse via this port.

• A USB-supported scanner or PC peripheral can be connected

to this port. (USB Hub Function. See page 4-3)

2. USB Port [PC] (Type B)

Connect this port to the USB port (type A) of your PC using a

USB cable. This port also serves as a PC Control port by using

Dynamic Image Utility 2.0 included on the supplied CD-ROM.

3. PC CARD Slot 1/2

Insert a PC card, commercially available flash memory card or

NEC optional wireless LAN card here.

There are two slots: Slot 1 and Slot 2.

4. PC CARD Eject Button 1/2

Press to eject a PC card partially. Each slot has its own eject

button: 1 and 2.

5. PC CONTROL Connectors (D-Sub 9 pin)

For system expansion such as PC-Control using Dynamic Im-

age Utility included on the supplied User Supportware CD-

ROM or RS232C control from an external control system.

IN: connect to the external equipment such as a PC or control

system.

OUT: for daisy-chaining multiple projectors and operating them

with the same external equipment. To do so, connect to a sec-

ond projector’ s IN terminal to relay the input at the IN terminal

of the first projector until all the projectors are connected.

6. SC. TRIGGER Mini Jack

When the projector is powered ON the screen trigger output

sends a low voltage trigger to the screen controller and the

screen will go down. When the projector is powered OFF the

screen trigger stops sending a low voltage trigger to the screen

controller and the screen will go up.

NOTE: To use this feature, you must turn on the Screen Trigger function. See

page 8-17.

Terminal Panel Features

1. Introduction

Tip (12V)

Ring (0V)

Sleave (ground. 0V)

Stereo mini cable

(not supplied)

NOTE: Screen controllers are supplied and supported by screen manufacturers.

NOTE: Do not use this jack for anything other than intended use. Connecting the

wired remote control to the SC. TRIGGER Mini Jack causes damage to the re-

mote control.

7. LAN Port (RJ-45)

This port is typically used for UTP Ethernet/Fast Ethernet. Use

this connector to control the projector on a LAN. See page

2-12.

8. REMOTE 1 (Mini D-Sub 15 Pin)

This terminal allows external control of the projector by use of

contact closure. See page 10-9.

9. REMOTE 2 Mini Jacks (IN/OUT)

IN: wired remote control input.

OUT: for daisy-chaining multiple projectors and operating them

with the same remote control. To do so, connect to a second

projector’ s IN terminal to relay the input at the IN terminal of

the first projector until all the projectors are connected.

10. Main Power Switch

When you plug the supplied power cable into an active wall

outlet and turn on the Main Power switch, the POWER indica-

tor turns orange and the projector is in standby mode. See

page 3-2.

11. AC IN

Connect the supplied power cable’s three-pin plug here.

Three types of power cable are supplied with this projector:

three-pin type for U. S. A. and Canada. Two-pin type for Europe

and Japan.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec gt6000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec gt6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info