Bedienungsanleitung Nec gt6000 (Seite 100 von 115) (Englisch)

216054

100

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

9-2

This chapter describes the simple maintenance procedures you

should follow to replace the lamp and the filter, and to clean the

filter and the cabinet.

z Replacing the Lamp

The projector has two lamps. The lamp replacement procedure

applies to both lamps. After your lamp 1 and 2 has been operat-

ing for 2000 hours (Normal mode on the standard life lamp) or

longer, the "Lamp" indicator in the cabinet will blink red and the

message will appear. Even though the lamp may still be working,

replace it as soon as possible to maintain optimal projector

performance.

NOTE: Be sure to use the same lamp type for both lamp 1 and 2.

CAUTION

• DO NOT TOUCH THE LAMP immediately after it has been used. It will

be extremely hot. Turn the projector off, wait 90 seconds (2 minutes in

the optional extended life lamp GT60LPS), turn off the main power

switch, and then disconnect the power cable. Allow at least one hour for

the lamp to cool before handling.

• DO NOT REMOVE ANY SCREWS except the lamp cover screw and

the two lamp case screws. You could receive an electrical shock.

• The projector will turn off and go into stand by mode after 2100 hours

(Normal mode on the standard life lamp) of service. If this happens, be

sure to replace the lamp. If you continue to use the lamp after 2000

hours (Normal mode on the standard life lamp) of use, the lamp bulb

may shatter, and pieces of glass may be scattered in the lamp housing.

Do not touch them as the pieces of glass may cause injury. If this hap-

pens, contact your NEC dealer for lamp replacement.

• When "Dual" is selected in "Lamp Select" of "Lamp Settings", replace

both lamp 1 and 2 at the same time so that the projected image will

keep an even color temperature.

To replace the lamp:

1. Loosen the lamp cover screw until the screwdriver goes into a free-

wheeling condition and remove the lamp cover. The lamp cover screw

is not removable.

2. Loosen the two screws securing the lamp housing until the screwdriver

goes into a freewheeling condition. The two screws are not removable.

Remove the lamp housing by pulling on the handle.

Interlock

3. Insert a new lamp housing until the lamp housing is plugged into the

socket.

CAUTION: Do not use a lamp other than the NEC replacement lamp

(Standard life lamp: GT60LP or Extended life lamp: GT60LPS).

4. Secure it in place with the two screws.

Be sure to tighten the screws.

5. Reattach the lamp cover.

9. Maintenance

6. Tighten the lamp cover screw. Be sure to tighten the screw.

NOTE: Replacing a new lamp automatically clears the lamp usage hours.

NOTE: The lamp housing has an EEPROM chip memorizing its amount of usage

hours. You can check the amount usage hours in Information of the menu. (The

standard lamp and the optional lamp have an EEPROM chip in it so that when you

remove it, your lamp usage hours are saved in its own memory. The projector

reads the lamp usage hours from the EEPROM chip to display them in Information

of the menu.)

NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do

not attempt to circumvent this interlock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec gt6000 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec gt6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info