Bedienungsanleitung Nec gt6000 (Seite 106 von 115) (Englisch)

216054

106

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

10-4

Does not turn on

Will turn off

No picture

Image isn’t square to the

screen

Picture is blurred

Image is scrolling verti-

cally, horizontally or

both

Remote control does

not work

Indicator is lit or blink-

ing

Cross color in RGB

mode

USB mouse does not

work

No on-screen menu

• Check that the power cable is plugged in and that the main power switch on the projector is on. See pages 1-

9 and 2-11.

• Ensure that the lens hood or the lamp cover is installed correctly. See pages 1-4 and 9-2.

• Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is

insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move

the projector to a cooler location.

• The lamp may fail to light. Wait a full minute and then turn on the power again.

• The lamp has reached the end of its usable life. Replace the lamp.

• Ensure that the Power Management is off. See page 8-16.

• Use the menu or Source/Input button to select your source (RGB 1/2, DVI, Video, S-Video, Viewer or LAN).

See page 3-3 or 8-7.

• Ensure your cables are connected properly.

• Use menus to adjust the brightness and contrast. See page 8-8.

• Select correct option in the Signal Select for current signal. See page 8-16.

• Select RGB/Component when connecting DVD player to RGB connector of the projector. See page 8-11.

• Apply a standard RGB signal when using RGB connector.

• Adjust picture for RGB signal.

• Make sure each setting is correct.

• If the problem still persists, reset the settings or adjustments to factory preset levels using the Factory Default

in the Adjustment Menu. See page 8-13.

• If Security is enabled, a keyword or PC card as a protect key is required.

• Remove the lens cap.

• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning

on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook

PC is turned on after connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver

or power management software.

* If you accidentally hit the POWER button on the remote control, wait 60 seconds and then press the POWER

button again to resume.

• See also the next page.

• Reposition the projector to improve its angle to the screen. See page 3-3.

• Use the 3DReform function to correct the trapezoid distortion. See page 3-4.

• Adjust the focus. See page 3-4.

• Reposition the projector to improve its angle to the screen. See page 3-3.

• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page

2-2.

• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

• Use the menus or Source/Input button on the remote control or the cabinet to select the source you want to

input. See page 3-3 or 8-7.

• Install new batteries. See page 1-12.

• Make sure there are no obstacles between you and the projector. See page 1-12.

• Stand within 22 feet (7 m) of the projector. See page 1-12.

• Check if one or more remote sensors are enabled. Select [Projector Options] → [Setup] → [Page 5] →

[Remote Sensor] from the menu. See page 8-17.

• If the remote control cable plug is inserted into the REMOTE 2 IN jack, the remote control does not function

wirelessly. See page 1-13.

• Make sure that the remote control’s ID corresponds with the projector’s ID. See page 7-2.

• See the Power/Status/Lamp Indicator on page 10-3.

• If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the Image Options. See

page 8-16.

• Make sure that your USB mouse is properly connected to the projector.

The projector may not support some brands of a USB mouse.

• Press MUTE OSD if the image is muted. Or press and hold CTL and press MUTE OSD button. See page 4-2.

Problem Check These Items

Common Problems & Solutions

10. Appendix

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec gt6000 Seite 106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec gt6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info