Bedienungsanleitung Nec GT950 (Seite 45 von 66) (Englisch)

493567

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

E – 45

[Page5]

Clear Lamp Hour Meter:

Resets the lamp clock back to zero. Pressing this button appears a

confirmation dialog box. To reset the lamp usage hour, press "OK".

NOTE: The projector will turn off and go into standby mode after 1600 hours

(up to 2100 hours in Eco mode) of service. If this happens, press the "Help"

button on the remote control for ten seconds to reset the lamp clock back

to zero. Do this only after replacing the lamp.

Clear Filter Usage:

Resets the filter usage back to zero. Pressing this button appears a

confirmation dialog box. To reset the filter usage hour, press "OK".

[Page4]

Auto Adjust:

When "Auto Adjust" is set to "On", the projector automatically de-

termines the best resolution for the current RGB input signal to

project an image using NEC's Advanced AccuBlend Intelligent Pixel

Blending Technology.

The image can be automatically adjusted for position and stability;

"Horizontal Position", "Vertical Position", "Clock" and "Phase".

On ................ Automatically adjusts image "Horizontal Position", "Vertical

Position", "Clock" and "Phase".

Off ................ User can adjust the image display functions ("Horizontal Po-

sition", "Vertical Position", "Clock" and "Phase") manually.

Auto Start:

Tur ns the projector on automatically when the power cable is in-

serted into an active power outlet. This eliminates the need to al-

ways use the "Power" button on the remote control or projector cabi-

net.

Power Management:

When this option is on and there is no RGB input for five minutes or

more, the projector will automatically turn itself off.

Power Off Confirmation:

This option determines whether a confirmation dialog for turning off

the projector will appear or not.

NOTE: When the confirmation message is displayed, you must be in the

Projector mode to operate your projector using the remote control. If not,

press the PJ button on the remote control to change your projector to the

Projector mode. The button lights to indicate that you are in the Projector

mode.

Keystone Save:

This option enables you to save your current keystone settings.

Saving your change once affects all sources. The changes are saved

when you turn off the projector.

Continuous Operation:

This option allows the cooling fans to run at a high speed in the Eco

mode.

When you wish to cool down the temperature inside the projector in

the Eco mode, check this box.

On: ............... Runs the cooling fans at a higher speed than normal opera-

tion.

NOTE: Be sure to select the Eco mode when turning on this option.

Off: .............. Sets the cooling fan speed appropriate for the temperature

inside the projector.

Remote Sensor:

This option determines which remote sensors on the projector are

enabled in wireless mode.

The options are: front, rear, right, or left. All checked boxes indicate

that they can accept the infrared signal from the supplied remote

control.

Control Panel Key Lock:

This option turns on or off the Control Panel Key Lock function.

NOTE:

* This Control Panel Key Lock does not affect the remote control and the

PC Control functions.

* When the cabinet buttons are disabled, pressing and holding the CAN-

CEL button for about 10 seconds will change the setting from "disabled"

to "enabled".

S-Video Mode Select:

This feature is used to select the S-Video signal detection mode.

This allows identifying of the S-Video signals with different aspect

ratio (Zoom signal 16:9, Wide Zoom signal 4:3).

S2 ............... Identifies Zoom or Wide Zoom signal.

OFF ............. Does not identify any S-video signal.

Built-in Speaker:

This option allows you to active the built-in speakers when you con-

nect an audio cable to the AUDIO OUT terminal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec GT950 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec GT950

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info