Bedienungsanleitung Nec HT1000 (Seite 21 von 61) (Englisch)

493570

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

E-21

5. Press the ENTER button.

6. Use the SELECT

̆̄̇̈

button to move the projected image frame

as shown on the example.

7. Press the ENTER button.

Screen

The confirmation screen is displayed.

On the Cornerstone adjustment screen, select

“Exit” and then “OK”, or press the CANCEL but-

ton on the remote control.

8. Use the SELECT

̆̄̇̈

button to select another icon which points

in the direction.

Screen

9. Press the SELECT

button to highlight the [OK] and press the

ENTER button.

This completes the keystone correction.

Selecting “Cancel” will return to the adjustment screen without saving

changes (Step 3).

Selecting "Reset" will return to the factory default.

Selecting "Undo" will exit without saving changes.

NOTE: To return the 3D Reform correction setting values to the factory default,

press and hold the 3D REFORM button for a minimum of 2 seconds.

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be

available. Should this happen, first reset the 3D Reform data and then do each

setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/

or Screen setting can limit 3D Reform in its adjustable range.

The adjustable ranges for 3D Reform are as follows:

Horizontal ........... Max ±25° approx.

Vertical ............... Max ±40° approx.

* The following are conditions at the above maximum angle when all of

the following are met

• Image is projected in Wide (Zoom lever)

• Resolution is XGA

Higher resolution than XGA limits 3D Reform in its adjustable range.

• Menu items should be set as follows:

Aspect Ratio ............................... Normal

Screen Type ................................ 4:3

• Horizontal and Vertical are adjusted separately.

A combination of both adjustments limits 3D Reform in its adjustable

range.

• When "Stadium" is selected in Aspect Ratio, "Cornerstone" and "Hori-

zontal Keystone" are not available.

Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

[Normal picture]

AUTO ADJ.

Press the Auto Adjust button to fine-tune the computer image or to re-

move any vertical banding that might appear and to reduce video noise,

dot interference or cross talk (this is evident when part of your image

appears to be shimmering). This function adjusts the clock frequencies

that eliminate the horizontal banding in the image. This function also

adjusts the clock phase to reduce video noise, dot interference or cross

talk. (This is evident when part of your image appears to be shimmer-

ing.)

This adjustment may be necessary when you connect your computer

for the first time.

NOTE:

• Some signals may not be displayed correctly or take time.

• The Auto Adjust function does not work for component and video signal.

• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock

and Phase manually. See page E-38.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec HT1000 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info