Bedienungsanleitung Nec HT410 (Seite 59 von 74) (Englisch)

493568

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

E-52

7. TROUBLESHOOTING

If there is no picture, or the picture is not displayed correctly.

•Power on process for the projector and the PC.

Be sure to connect the RGB cable between the projector and the computer before turning on the computer.

There are some notebook PCs, which do not output signal unless there is a projector or monitor connected

first.

NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0

kHz”, this means there is no signal being output from the computer. See page E-43 or go to next step.

• Enabling the computer’s external display.

Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the

projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external

display. Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external

display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combi-

nations to toggle through external display selections.

• Non-standard signal output from the computer

If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed

correctly.

Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each

notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous

step. Refer to your computer’s documentation for detailed information.

• Image displayed is incorrect when using a Macintosh

When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the

projector) according to your resolution. After setting, restart your Macintosh for the changes to take affect.

For setting display modes other than those supported by your Macintosh and the projector, changing the DIP

switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the

DIP switch to the 13" fixed mode and then restart your Macintosh. After that, restore the DIP switches to a

displayable mode and then restart the Macintosh again.

NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-

Sub 15-pin connector.

• Mirroring on a PowerBook

* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-

ing” is off on our PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.

•Folders or icons are hidden on the Macintosh screen

Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple

menu and arrange icons.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec HT410 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec HT410

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info