Bedienungsanleitung Nec LT140 (Seite 16 von 43) (Englisch)

493579

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

E–16

When using a Macintosh with the projector, set the DIP switches of

the supplied pin adapter according to your resolution. After setting,

restart your Macintosh.

See the following pages for setting of the DIP switches.

• When using with a Macintosh, SVGA(800ן600)/

XGA(1024ן768) is recommended if your Macintosh supports

this mode.

• When using with a Macintosh PowerBook, output may not be

set to 800ן600 unless “mirroring” is off on your PowerBook.

Refer to owner’s manual supplied with your Macintosh com-

puter for mirroring.

NOTE: A Video Adapter cable manufactured by Apple Computer is

needed for a PowerBook which does not have a mini D-Sub 15-pin

connector.

Settings for Monitor Mode

Number of DIP switch

1 23 456

Resolution

13" multi-scan mode /16"-13" ON ON ON ON

17" multi-scan mode /19"-13" ON ON ON

21” multi-scan mode /21"-13" ON ON ON

13" fixed mode /640x480 ON ON

VGA/SVGA mode ON ON

16" fixed mode /832x624 ON ON

19" fixed mode /1024x768 ON ON

21" fixed mode /1152x870 ON ON ON ON

NOTE: For settings other than display modes supported by your

Macintosh and the projector, use of the DIP switch may bounce an

image slightly or may display nothing. If this happens, set the DIP

switch to the 13" fixed mode and then restart your Macintosh. After

that, restore to a displayable mode and then restart the Macintosh

again. Make sure that the projector and your Macintosh are con-

nected with the pin adapter and the supplied signal cable (mini D-

Sub 15-pin connector) and then restart your Macintosh.

Examples of DIP switch setting

17" multi-scan mode VGA/SVGA mode 19" fixed mode

NOTE: Refer to your computer’s owner’s manual for more informa-

tion about your computer’s video output requirements and any spe-

cial identification or configuring your projector’s image and moni-

tor may require.

Connecting Your DVD Player

You can connect your projector to a DVD player with component

outputs or Video output. To do so, simply:

1. Turn off the power to your projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output,

use the optional 15-pin-to-RCA x 3 cable to connect your DVD

player to the RGB INPUT connector on the projector.

For a DVD player without component video (Y,Cb,Cr) outputs,

use common RCA cables (not provided) to connect a composite

VIDEO output of the DVD player to the Video Input of the pro-

jector.

3. Turn on the projector and the DVD player.

NOTE: Refer to your DVD player’s owner’s manual for more infor-

mation about your DVD player’s video output requirements.

Connecting Your VCR or Laser Disc Player

Use common RCA cables (not provided) to connect your VCR or

laser disc player to your projector. To make these connections, sim-

ply:

1. Turn off the power to the projector and VCR or laser disc player.

2. Connect one end of your RCA cable to the video output connector

on the back of your VCR or laser disc player, connect the other

end to the Video input on your projector. Use standard RCA audio

patch cords to connect the audio from your VCR or laser disc

player to the projector (if your VCR or laser disc player has this

capability). Be careful to keep your right and left channel connec-

tions correct for stereo sound.

3. Turn on the projector and the VCR or laser disc player.

NOTE: Refer to your VCR or laser disc player owner’s manual for

more information about your equipment’s video output requirements.

Connecting Your Computer to the Mouse Output Port

(only when using the optional full function remote control)

NOTE: To use the Mouse Output port, you need the optional serial

cable, the optional mouse adapter(for IBM PS/2 or Macintosh), and

the optional full function remote control.

The built-in remote mouse receiver enables you to operate your

computer’s mouse functions from the optional full function remote

control. It is a great convenience for clicking through your computer-

generated presentations.

To connect the mouse output port:

1. Turn off your computer.

2. For PCs: Remove your current mouse and connect the optional

serial cable from the mouse output to your PC’s mouse port. (Use

the 6-pin adapter for connecting to a PS/2 computer.)

For Macintosh: Remove your current mouse from your computer,

attach the Macintosh adapter to the mouse output port’s serial cable,

and connect the projector to your mouse port.

3. When the built-in remote mouse receiver is available, it will dis-

able your regular mouse, disconnect the serial cable and restart

your computer.

321

654321

654 321

654

PC CONTROL

USB

RGB INPUT S-VIDEO

VIDEO AUDIO

(

MONO

)

PC CARD

ACCESS

MOUSE OUT

PC CONTROL

USB

RGB INPUT S-VIDEO

VIDEO AUDIO

(

MONO

)

PC CARD

ACCESS

MOUSE OUT

Serial cable (included

with the optional full

function remote control)

Serial cable (included

with the optional full

function remote control)

IBM PC/AT

Macintosh

IBM PS2

NOTE:Some computers or software programs may not work with the

MOUSE OUT port.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec LT140 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec LT140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info