Bedienungsanleitung Nec LT155 (Seite 39 von 57) (Englisch)

493577

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

E – 38

Communication Speed:

This feature sets the baud rate of the PC Control port (Mini DIN 8

Pin).

It supports data rates from 4800 to 38400 bps.

The default is 38400 bps. Select the appropriate baud rate for your

equipment to be connected.

Default Source Select:

You can set the projector to default to any one of its inputs each

time the projector is turned on.

Last .............. Sets the projector to default to the previous or last active

input each time the projector is turned on.

Auto ............. Searches for an active source in order of RGB* → Video →

S-Video → PC Card Viewer → RGB and displays the first

found source.

Select ........... Displays the selected source input every time the projector is

started up. Select an input from the pull-down menu.

* "DVI (DIGITAL) → DVI (ANALOG)" on LT156.

[Page4]

Auto Adjust (RGB Only):

When "Auto Adjust" is set to "On", the projector automatically de-

termines the best resolution for the current RGB input signal to

project an image using NEC's Advanced AccuBlend Intelligent Pixel

Blending Technology.

The image can be automatically adjusted for position and stability;

"Horizontal Position", "Vertical Position", "Clock", "Phase", and

"Resolution."

On ................ Automatically adjusts image "Horizontal Position", "Vertical

Position", "Clock", "Phase" and "Resolution".

Off ................ User can adjust the image display functions ("Horizontal Po-

sition", "Vertical Position", "Clock", "Phase" and "Resolution")

manually.

NOTE: For LT156

This feature is not available for DVI (DIGITAL) signal.

If you make any adjustment to DVI digital signal, the Auto Adjust feature

automatically adjusts position and stability; Horizontal and Vertical Posi-

tion, and Resolution. However, the horizontal and vertical adjustments will

not be stored in memory.

Auto Start:

Turns the projector on automatically when the power cable is in-

serted into an active power outlet. This eliminates the need to al-

ways use the "Power" button on the remote control or projector cabi-

net.

Power Management:

When this option is on and there is no RGB input for five minutes or

more, the projector will automatically turn itself off.

Power Off Confirmation:

This option determines whether a confirmation dialog for turning off

the projector will appear or not.

NOTE: When the confirmation message is displayed, you must be in the

Projector mode to operate your projector using the remote control. If not,

press the PJ button on the remote control to change your projector to the

Projector mode. The button lights to indicate that you are in the Projector

mode.

Keystone Save:

This option enables you to save your current keystone settings.

Saving your change once affects all sources. The changes are saved

when you turn off the projector.

Clear Lamp Hour Meter:

Resets the lamp clock back to zero. Pressing this button appears a

confirmation dialog box. To reset the lamp usage hour, press "OK".

NOTE: The projector will turn off and go into standby mode after 1100 hours

(up to 2200 hours in Eco mode) of service. If this happens, press the "Help"

button on the remote control for ten seconds to reset the lamp clock back

to zero. Do this only after replacing the lamp.

[Page5]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec LT155 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec LT155

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info