Bedienungsanleitung Nec mt 860 (Seite 22 von 65) (Englisch)

214296

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

E-22

Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

[Normal picture]

AUTO ADJ.

Press the Auto Adjust button to fine-tune the computer image or to re-

move any vertical banding that might appear and to reduce video noise,

dot interference or cross talk (this is evident when part of your image

appears to be shimmering). This function adjusts the clock frequencies

that eliminate the horizontal banding in the image. This function also

adjusts the clock phase to reduce video noise, dot interference or cross

talk. (This is evident when part of your image appears to be shimmer-

ing.)

This adjustment may be necessary when you connect your computer

for the first time.

NOTE:

• Some signals may not be displayed correctly or take time.

• The Auto Adjust function does not work for component and video signal.

• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock

and Phase manually. See page E-39.

• Pressing and holding the AUTO ADJUST button on the cabinet or AUTO ADJ

button on the remote control for a minimum of 2 seconds will enable the Auto

Focus* and the Auto Wall Color Correction* feature instead of the Auto Adjust

feature. (The Auto Focus and the Auto Wall Color Correction features are not

available on MT860.)

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be

available. Should this happen, first reset the 3D Reform data and then do each

setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/

or Screen setting can limit 3D Reform in its adjustable range.

The adjustable ranges for 3D Reform are as follows:

Horizontal ........... Max ±35° approx.

Vertical ............... Max +50°/-25° approx.

* The following are conditions at the above maximum angle when all of

the following are met

• Image is projected in Wide (Zoom)

• Resolution is XGA (SVGA on MT860)

Higher resolution than XGA limits 3D Reform in its adjustable range.

• Menu items should be set as follows:

Aspect Ratio ............................... 4:3

Screen Type ................................ 4:3

• Horizontal and Vertical are adjusted separately.

A combination of both adjustments limits 3D Reform in its adjustable

range.

• When "4:3 Fill" is selected in Aspect Ratio, "Cornerstone" and "Hori-

zontal Keystone" are not available.

Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT jack (RCA) on the

projector can be adjusted.

increase volume

Volume bar

decrease volume

VOLUME

Using the Laser Pointer

You can use the laser to draw your audience's attention to a red dot that

you can place on any object.

Press and hold the LASER button to activate the laser pointer.

CAUTION:

• Do not look into the laser pointer while it is on.

• Do not point the laser beam at a person.

POINTER

MAGNIFY

PIC-MUTE

FOLDER

SLIDE

FREEZE

FOCUS

LASER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec mt 860 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec mt 860

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info