Bedienungsanleitung Nec MT1040 (Seite 17 von 42) (Englisch)

493583

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

E–17

3.OPERATION

This section describes how to select a computer or video source, how

to adjust the picture, and how to customize the menu or projector

settings.

General Controls

Before you turn on your projector, ensure that the computer or video

source is turned on and that your lens cap is removed.

1. Turn on the Projector

Plug the supplied power cable in the wall outlet. The projector

will go into its standby mode and the power indicator will glow

amber.

Only after you press the “On” button on the projector cabinet or

the full function remote control will the power indicator turn to

green and the projector become ready to use.

NOTE: To turn the projector on by plugging in the power cable,

use the menu and enable the “Auto Start” feature. (See page E-

23.)

2. Select the Computer, Video Source or PC Card Viewer

Press the Source button on the remote control or the projector

cabinet to select “Video” (VCR, document camera, or laser disc

player), S-Video”, “RGB 1 / 2” (computer or DVD with compo-

nent output) or “PC Card Viewer” to display the image.

Or press the “Menu” button on the remote control or the cabinet

and use the menu to select your video source: “Video”, “S-Video”,

“RGB1 / 2”, or “PC Card Viewer”.

3. Adjust the Image Size and the Focus

Use the Zoom ring to adjust the image size, then use the Focus

ring knob to obtain the best focus.

Use the “Magnify” button (+) or (-) on the remote control to make

the image larger up to 400%.

4. Turning off the Projector

First press the “off” button on the projector cabinet or the remote

control for a minimum of two seconds. The power indicator will

glow amber. Then, unplug the power cable. The power indicator

will go out.

IMPORTANT:

• The projector should be unplugged if it will not to be used for an

extended period.

• To turn off the image and sound briefly (five minutes or less),

use the “Picture Mute” button instead of turning the projector

off and on.

• The projector will display a black, blue image or logo if no input

signal is present.

• Do not turn the projector off and then immediately back on. The

projector needs to cool for a minute before it can be restarted.

After the projector turns off, the cooling fans keep operating for a

full minute.

Do not disconnect the power cable during this time.

Using the Menus

NOTE: The on-screen menu may not be displayed correctly while

interlaced motion video image is projected.

1. Press the “Menu” button on the remote control or projector cabi-

net to display the Main Menu.

NOTE: When using a USB mouse, click the mouse button to dis-

play the main menu. For other operations, do the same way as

you use your PC mouse.

2. Press the ▲▼ buttons on the full function remote control or the

projector cabinet to highlight the menu for the item you want to

adjust or set.

3. Press the ᮣ button or the “Enter” button on the projector cabinet

or the “Left Click” button on the full function remote control to

select a submenu or item.

4. Adjust the level or turn the selected item on or off by using “Se-

lect” ᮤ or ᮣ buttons on the cabinet, or the “Mouse pad” on the

full function remote control. The on-screen slide bar will show

you the amount of increase or decrease.

5. The change is stored until you adjust it again.

ENTER: Stores the setting or adjustments.

CANCEL: Return to the previous screen without storing settings

or adjustments.

NOTE: You can close the main and sub menus simultaneously by

pressing the Computer/Projector Select button to cancel the Pro-

jector mode.

6. Repeat steps 2-5 to adjust an additional item, or press “Cancel”

on the projector cabinet or the remote control to quit the menu

display.

Using a USB Mouse

Using a USB mouse gives you a smooth operation. A commercially

available USB mouse is required.

NOTE:There may be some brands of USB mouse that the projector

does not support.

Operate the Menus using the USB mouse

Mouse Cursor

When connecting a USB mouse to the projector, you get a mouse

cursor on the screen.

Unless you use your USB mouse within 10 seconds, the mouse

cursor disappears.

Menu Display

Clicking with a mouse button displays the main menu.

Clicking

displays the pull-down menu.

To close the menu, click anywhere in the background.

Adjusting and Setting Display

You can select a menu item and click with a mouse button to

make adjustments and setting.

Examples

Click (or press and hold) the mouse button ᮤ or ᮣ to adjust the

brightness.

Or click and drag the mouse button on the slide bar horizontally

to adjust it.

To save the adjustments, click

. The display is closed.

If you click anywhere in the background while displaying adjust-

ment and setting menu or dialog box, you will get the main menu

at the clicking point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MT1040 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec MT1040

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info