Bedienungsanleitung Nec MT1060 (Seite 56 von 65) (Englisch)

654055

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

E-56

Does not turn on

No picture

Image isn’t square to the

screen

Picture is blurred

Image is scrolling verti-

cally, horizontally or

both

Remote control does

not work

Indicator is lit or blink-

ing

Cross color in RGB

mode

USB mouse does not

work

• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote

control is on. See pages E-17 and 18.

• Ensure that the lamp cover or lamp housing is installed correctly. See page E-53.

• Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is

insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move

the projector to a cooler location.

• Use the menu to select your source (RGB 1/2, Video, S-Video, DVI, Viewer or LAN). See page E-19.

• Ensure your cables are connected properly.

• Use menus to adjust the brightness and contrast. See page E-38.

• Remove the lens cap.

• Reset the settings or adjustments to factory preset levels using the Factory Default in the Adjustment Menu.

See page E-52.

• Reposition the projector to improve its angle to the screen. See page E-19.

• Use the 3DReform function to correct the trapezoid distortion. See page E-20.

• Adjust the focus. See page E-20.

• Reposition the projector to improve its angle to the screen. See page E-19.

• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page

E-12 and 13.

• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

• Use menus or Source button on the remote control or the cabinet to select the source you want to input.

• Install new batteries. See page E-11.

• Make sure there are no obstacles between you and the projector.

• Stand within 22 feet (7 m) of the projector. See page E-11.

• Make sure that you are in the Projector mode and the PJ button lights in red. If not, press the PJ button. See

page E-24.

• See the Status Indicator on pages E-55.

• If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the Image Options. See

pages E-39 and 45.

• Make sure that your USB mouse is properly connected to the projector.

The projector may not support some brands of a USB mouse.

Problem Check These Items

Common Problems & Solutions

When using the Viewer function

• Is “Viewer” selected from the Source menu?

• Is the PC card seated in the PC Crad slot completely?

• Are slide data stored in the PC card?

• Have the contents of the PC card been destroyed?

• While an image with over 1024⳯768 dots is projected, several lines of information will be lost. Use

the supplied software change the image to 1024⳯768 dots in size.

• Use a computer, etc., to repair the data.

Problem Check These Items

For more information contact your dealer.

No picture

Part of a slide is not displayed

Contents of PC Card are damaged

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MT1060 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec MT1060

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info