Bedienungsanleitung Nec MT1075 (Seite 43 von 69) (Englisch)

493585

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

E-43

Using Adapting Color Correction [Wall Color Correction]

The correction mode select screen will be displayed.

*To read the pre-adjustment settings. Choose a selection from User 1

– 4, highlight "OK" and press the ENTER button.

3. Use the SELECT

button to highlight "Execute" and then press the

ENTER button.

The Auto Wall Color Correction will be executed.

NOTE: When Auto Wall Color Correction is enabled in the Auto Functions menu,

Wall Color Correction can be executed by pressing and holding the AUTO AD-

JUST or AUTO ADJ button for a minimum of 2 seconds.

Manual Wall Color Correction

Preparation: Before correcting manually, prepare a non-glossy, non-

transparent, clean white paper (300 mm ן 420 mm). Hereafter re-

ferred to as "the white paper for Wall Color Correction."

1. Choose a selection from User 1 – 4. Highlight "Setting" and press the

ENTER button.

The correction mode select screen is displayed.

*To read the pre-adjustment settings. Choose a selection User 1 – 4,

highlight "OK" and press the ENTER button.

2. Highlight "Manual".

3. Use the SELECT

button to highlight "Execute" and then press the

ENTER button.

The Manual Wall Color Correction (Red) screen will be displayed.

Working area

This function allows for correcting the color of the projected images on

textured walls using the image sensor on the projector. There are two

ways for color correction: Automatic and Manual. Automatic correction

affects all colors; Manual correction allows you to correct each color R,

G, B, and W respectively.

Off .................. Disables this function

User 1 to 4 ..... Executes correction. Four settings can be saved.

User 4 (AutoAdjustButton) stores settings when the

Auto Function is executed by pressing and holding

the AUTO ADJUST button or AUTO ADJ. button for a

minimum of 2 seconds.

Info box .......... Displays "Automatic" or "Manual". This is the option

you have set for User 1 – 4 setting.

NOTE: Correction may not be possible depending on ambient room lighting,

walls with a texture that is glossy or with certain patterns, or walls that are the

color black or primary deep colors.

If you try to correct beyond the limit, an error message "Out of correction range!"

will be displayed. This message means that you will not be able to correct the

color due to the above reasons.

Also, When the image sensor fails to pick up the image of a wall color during

Auto Wall Color Correction, an error message "Failed to execute Auto Wall Color

Correction" will be displayed. This message means that there may be an obstacle

between the wall and the image sensor on the projector, or the image sensor

may not work because of too much ambient light. Make corrections to what

seems to be the problem and try again.

Automatic Wall Color Correction

1. Choose a selection from User 1 – 4. Highlight "Setting" and press the

ENTER button.

2. Highlight "Automatic".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MT1075 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec MT1075

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info