Bedienungsanleitung Nec MultiSync X461S (Seite 14 von 42) (Englisch)

493561

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English-12

1. Determine the installation location

CAUTION: Installing your LCD monitor must be done by a

qualiﬁ ed technician. Contact your dealer for more

information.

CAUTION:

MOVING OR INSTALLING THE LCD MONITOR

MUST BE DONE BY TWO OR MORE PEOPLE.

Failure to follow this caution may result in injury if

the LCD monitor falls.

CAUTION: Do not mount or operate the monitor upside

down or face down.

CAUTION: This LCD has a temperature sensor and cooling

fan. If the LCD becomes too hot, the cooling fan

will turn on automatically. If the LCD becomes

overheated while the cooling fan is running, a

“Caution” warning will appear. If the “Caution”

warning appears, discontinue use and allow the

unit to cool. Using the cooling fan will reduce

the likelihood of early circuit failure and may

help reduce image degradation and “Image

Persistance”.

If the LCD is used in an enclosed area or if the

LCD panel is covered with a protective screen,

please check the inside temperature of the

monitor by using the “HEAT STATUS” control

in the OSD (see page 24). If the temperature is

higher than the normal operating temperature,

please turn the cooling fan to ON within the FAN

CONTROL menu within the OSD (see page 24).

IMPORTANT: Lay the protective sheet, which was wrapped

around the LCD monitor when it was

packaged, beneath the LCD monitor so as not

to scratch the panel.

2. Install the remote control batteries

The remote control is powered by two 1.5V AA batteries.

To install or replace batteries:

A. Press and slide to open the cover.

B. Align the batteries according to the (+) and (–) indications

inside the case.

C. Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or

bursting.

NEC recommends the following battery use:

• Place “AA” size batteries matching the (+) and (-) signs

on each battery to the (+) and (-) signs of the battery

compartment.

• Do not mix battery brands.

• Do not combine new and old batteries. This can shorten

battery life or cause liquid leakage of batteries.

• Remove dead batteries immediately to prevent battery

acid from leaking into the battery compartment.

• Do not touch exposed battery acid, it may injure skin.

NOTE: If you do not intend to use the Remote Control for

a long period of time, remove the batteries.

3. Connect external equipment

(See pages 14 and 15)

• To protect the external equipment; turn off the main power

before making connections.

• Refer to your equipment user manual for further

information.

NOTE: Do not connect/disconnect cables when turning

on the monitor or other external equipment as this

may result in a loss of the monitor image.

4. Connect the supplied power cord

• The equipment should be installed close to an easily

accessible power outlet.

• Please fasten power cord to the LCD monitor by attaching

the screw and clamp.

• Fully insert the prongs into the power outlet socket.

A loose connection may cause image degradation.

NOTE: Please refer to the “Safety Precautions and

Maintenance” section of this manual for proper

selection of AC power cord.

Screw

Clamp

Setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MultiSync X461S Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info