Bedienungsanleitung Nec MultiSync X551S (Seite 8 von 42) (Englisch)

493562

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English-6

Attaching Mounting Accessories

The monitor is designed for use with the VESA mounting

system.

1. Attach Mounting Accessories

Be careful to avoid tipping monitor when attaching

accessories.

VESA Mounting Interface

300 mm

Mounting accessories can be attached with the monitor in

the face down position. To avoid damaging the screen face,

place the protective sheet on the table underneath the LCD.

The protective sheet was wrapped around the LCD in the

original packaging. Make sure there is nothing on the table

that can damage the monitor.

When using mounting accessories other than NEC compliant

and approved, they must comply with the VESA-compatible

mounting method.

2. Using Option Board

1. Turn off the main power switch.

2. Remove the attached slot cover by unscrewing the

installed screws (Figure 1).

3. Insert option board in to the monitor (Figure 2).

NOTE: Please contact your supplier for available option

boards.

4. Place the cover for the option board slot over the option

board. This is included with the monitor.

5. Secure the cover by using the two screws from step 2

(Figure 3).

Figure 1 Figure 2 Figure 3

Screw for Option board slot

Mounting location

• The ceiling and wall must be strong enough to support the

monitor and mounting accessories.

• DO NOT install in locations where a door or gate can hit

the unit.

• DO NOT install in areas where the unit will be subjected

to strong vibrations and dust.

• DO NOT install near where the main power supply enters

the building.

• Do not install in where people can easily grab and hang

onto the unit or the mounting apparatus.

• When mounting in a recessed area, as in a wall, leave at

least 4 inches (100 mm) of space between the monitor

and the wall for proper ventilation.

• Allow adequate ventilation or provide air conditioning

around the monitor, so that heat can properly dissipate

away from the unit and mounting apparatus.

Mounting on ceiling

• Ensure that the ceiling is sturdy enough to support the

weight of the unit and the mounting apparatus over time,

against earthquakes, unexpected vibrations, and other

external forces.

• Be sure the unit is mounted to a solid structure within

the ceiling, such as a support beam. Secure the monitor

using bolts, spring lock washers, washer and nut.

• DO NOT mount to areas that have no supporting internal

structure. DO NOT use wood screws or anchor screws for

mounting. DO NOT mount the unit to trim or to hanging

ﬁ xtures.

Maintenance

• Periodically check for loose screws, gaps, distortions,

or other problems that may occur with the mounting

apparatus. If a problem is detected, please refer to

qualiﬁ ed personnel for service.

• Regularly check the mounting location for signs of

damage or weakness that may occur over time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec MultiSync X551S Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info