Bedienungsanleitung Nec NP-ME301W (Seite 119 von 133) (Englisch)

654043

119

Zoom out

Zoom in

Vorherige Seite

1/133

Nächste Seite

108

8. Appendix

❶ Troubleshooting

Thissectionhelpsyouresolveproblemsyoumayencounterwhilesettinguporusingtheprojector.

Indicator Messages

PowerIndicator

Indicator Condition ProjectorCondition Note

Off The main power is off –

Blinking light Blue

0�5 sec On,

0�5 sec Off

The projector is getting ready to turn on� Wait for a moment�

2�5 sec On,

0�5 sec Off

Off Timer is enabled� –

Orange 0�5 sec On,

0�5 sec Off

Cooling Wait for a moment

Steady light Blue

The projector is turned on� –

Orange In Standby condition [NETWORK STANDBY] is

selected for [STANDBY MODE]

–

Red In Standby condition [NORMAL] is selected for

[STANDBY MODE]

–

Status Indicator

Indicator Condition ProjectorCondition Note

Off Normal or Standby –

Blinking light Red

1 cycle (0�5 sec

On, 2�5 sec Off)

Lamp cover error or lamp housing error Mount the lamp cover or lamp housing correctly�

2 cycle (0�5 sec

On, 0�5 sec Off)

Temperature error The projector is overheated� Move the projector to

a cooler location�

3 cycle (0�5 sec

On, 0�5 sec Off)

Power error Power unit is not working properly� Contact your

dealer�

4 cycle (0�5 sec

On, 0�5 sec Off)

Fan error Fans will not work correctly�

6 cycle (0�5 sec

On, 0�5 sec Off)

Lamp error Lamp fails to light� Wait a full minute and then turn

on again�

Green 1 cycle (0�5 sec

On, 0�5 sec Off)

Re-ﬁring the lamp (The projector is cooling down�) The projector is re-ﬁring�

Wait for a moment�

Orange 1 cycle (0�5 sec

On, 2�5 sec Off)

Network conﬂict

Both the built-in wired LAN and the wireless LAN cannot

be connected to the same network at the same time�

To use both built-in wired LAN and wireless LAN at the

same time, connect them to different networks�

NOTE:IntheStandbycondition,thestatusindicator

onthecabinetdoesnotblinkinorangeevenifthe

networkconicts

Steady light Green

Sleep mode

–

Orange

CONTROL PANEL LOCK is on� You have pressed cabinet button when Control

Panel Lock is on�

CONTROL ID error Remote control ID and projector ID are not matched�

Lamp Indicator

Indicator Condition ProjectorCondition Note

Off Normal –

Blinking light Red

Lamp has reached its end of life� Lamp replace-

ment message will be displayed�

Replace the lamp�

Steady light Red Lamp has been used beyond its limit� The projector

will not turn on until the lamp is replaced�

Replace the lamp�

Green In the state of [ECO MODE] ([AUTO ECO], [NOR-

MAL], OR [ECO])

–

Over-TemperatureProtection

Ifthetemperatureinsidetheprojectorrisestoohigh,theover-temperatureprotectorwillautomaticallyturnoffthelamp

withtheSTATUSindicatorblinking(2-cycleOnandOff.)

Shouldthishappen,dothefollowing:

• Unplugthepowercordafterthecoolingfansstop.

• Movetheprojectortoacoolerlocationiftheroomwhereyouarepresentingisparticularlytoowarm.

• Cleantheventsiftheyarecloggedwithdust.

• Waitabout60minutesuntiltheinsideoftheprojectorbecomescoolenough.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec NP-ME301W Seite 119

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec NP-ME301W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info