Bedienungsanleitung Nec NP110 (Seite 69 von 97) (Englisch)

654085

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

5. Using On-Screen Menu

SelectingCommunicationSpeed[COMMUNICATIONSPEED]

This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The

default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equip-

ment, a lower baud rate may be recommended for long cable runs).

NOTE:Yourselectedcommunicationspeedwillnotbeaffectedevenwhen[RESET]isdonefromthemenu.

SettingIDtotheProjector[CONTROLID]

You can operate multiple projectors separately and independently with the single remote control that has the CONTROL

ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together

using the single remote control. To do so, you have to assign an ID number to each projector.

CONTROL ID NUMBER .......Select a number from 1 to 254 you wish to assign to your projector.

CONTROL ID

.......................Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set-

ting.

NOTE:

•

When[ON]isselectedfor[CONTROLID],theprojectorcannotbeoperatedbyusingtheremotecontrolthatdoesnotsupport

theCONTROLIDfunction.(Inthiscasethebuttonsontheprojectorcabinetcanbeused.)

• Yoursettingwillnotbeaffectedevenwhen[RESET]isdonefromthemenu.

•PressingandholdingtheENTERbuttonontheprojectorcabinetfor10secondswilldisplaythemenuforcancelingtheControl

ID.

AssigningorChangingtheControlID

1. Turn on the projector.

2. Press the ID SET button on the remote control.

The CONTROL ID screen will be displayed.

If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed. If the projector

cannot be operated with the current remote control ID, the [INACTIVE] will be displayed. To operate the inactive

projector, assign the control ID used for the projector by using the following procedure (Step 3).

3. Press one of numeric keypad buttons while pressing and holding the ID SET button on the remote con-

trol.

Example:

To assign “3”, press the “3” button on the remote control.

No ID means that all the projectors can be operated together with a single remote

control. To set “No ID”, enter “000” or press the CLEAR button.

TIP:TherangeofIDsisfrom1to254.

4. Release the ID SET button.

The updated CONTROL ID screen will be displayed.

NOTE:

• TheIDscanbeclearedinafewdaysafterthebatteriesarerundownorremoved.

• Accidentallypressinganyoneofthebuttonsoftheremotecontrolwillclearcurrentlyspecied

IDwithbatteriesremoved.

＋

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec NP110 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec NP110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info