Bedienungsanleitung Nec np115 (Seite 51 von 97) (Englisch)

216191

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

4. Convenient Features

Invertingtheorderofdisplayingtheimagesforlefteyeandrighteye[L/RINVERT]

This function changes the order of displaying the images for left eye and right eye.

Change the setting if you have difﬁculty seeing 3D images.

• EachtimeyoupressthePICTUREbuttonontheremotecontrol,thefollowingmenuitemswillchange:

 [L/RINVERT]→[CONTRAST]→[BRIGHTNESS]→ ...

NOTE:When[OFF]isselectedfor[DLP

Link],thisfunctionisnotavailable.

NOTE:

• If3DcontentisplayedbackonyourcomputerandtheperformanceispooritmaybecausedbytheCPUorgraphicschip.Inthis

caseyoumayhavedifcultyseeingthe3Dimagesastheywereintended.Checktoseeifyourcomputermeetstherequirements

providedinyouruser'smanualincludedwithyour3Dcontent.

• TheDLP

LinkcompatibleLCDshuttereyeglassesallowyoutoview3Dimagesbyreceivingsynchsignals,whichareincluded

inlefteyeandrighteyeimages,reectedfromthescreen.Dependingonenvironmentsorconditionssuchastheambientbright-

ness,screensizeorviewingdistance,theLCDshuttereyeglassesmayfailtoreceivesynchsignals,causingpoor3Dimages.

• Whenthe3Dmodeisenabled,[3D]willbedisplayedinthe[SOURCE]menu.

• Whenthe3Dmodeisenabled,theKeystonecorrectionrangewillbenarrower.

• Whenthe3Dmodeisenabled,thefollowingsettingsareinvalid.

 [WALLCOLOR],[PRESET],[REFERENCE],[COLORTEMPERATURE]

• Refertothe[SOURCE]screenunderthe[INFO.]menuforinformationonwhethertheinputsignalis3Dcompatible.

• Signalsotherthanthoselistedbelowwillbeoutofrangeorwillbedisplayedin2D.

 [COMPUTER]/[COMPUTER1/COMPUTER2(NP216only)]

 640x480@120Hz,800x600@120Hz,1024x768@120Hz,1280x720@120Hz,640x480@60Hz,800x600@60Hz,1024x768@60Hz,

1280x720@60Hz

 [VIDEO/S-VIDEO]

 Signalswithverticalfrequencyof60Hz

Troubleshootingonviewing3Dimages

If images will not be displayed in 3D or 3D images appear as 2D, check the following table. Also refer to the user's

manual accompanied with your 3D content or LCD shutter eyeglasses.

Possiblecauses Solutions

• Thecontentyouareplayingbackisnotcompatiblewith3D. • Playbackacontentcompatiblewith3D.

• The3Dmodewasturnedofffortheselectedsource.

• Usetheprojector'smenutoturnon3Dmodefortheselected

source. (→ page 41)

• YouarenotusingourrecommendedLCDshuttereyeglasses.

• UseourrecommendedLCDshuttereyeglasses.(→ page 40)

• IftheshutterofyourDLP®LinkcompatibleLCDshuttereye-

glassescannotsynchronizewiththecurrentlyprojectedsource,

the following are possible causes:

- Your LCD shutter eyeglasses are not switched on. • SwitchonyourLCDshuttereyeglasses.

- The battery in the LCD shutter eyeglasses ran down. • Rechargethebatteryorreplaceit.

- [DLP®Link]wasnotturnedon.

• Use the projector's menu to turn on [DLP® Link].(→ page

41)

- The viewing distance between the viewer and the screen is

too far.

• Moveclosertothescreenuntiltheviewergets3Dimages.

• Orusetheprojector'smenutoselect[NON-INVERT]for[L/R

INVERT].

- There are bright light sources or other projectors near the

viewer.

• Keeplightsourcesorotherprojectorsawayfromtheviewer.

• Donotlooktowardabrightlightsource.

• Orusetheprojector'smenutoselect[NON-INVERT]for[L/R

INVERT].

• If your computeris not setfor3D viewing,the following are

possible causes:

- Your computer does not meet the requirements for 3D view-

ing.

• Checktoseeifyourcomputermeetstherequirementsprovided

in your user's manual included with your 3D content.

- Your computer is not set for 3D output. • Setyourcomputerfor3Doutput.

- The resolution of output signal is out of range. • Selecttheresolutionofoutputsignalsupporting3D.

- The refresh rate of output signal is out of range. • Changetherefreshrateto60Hzor120Hz.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec np115 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec np115

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info