Bedienungsanleitung Nec np210 (Seite 83 von 97) (Englisch)

216188

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

7. Appendix

CommonProblems&Solutions (→ “Power/Status/Lamp Indicator” on page 73.)

Problem CheckTheseItems

Does not turn on

or shut down

• Checkthatthepowercableispluggedinandthatthepowerbuttonontheprojectorcabinetortheremote

control is on. (→ pages 17 and 18)

• Ensurethatthelampcoverisinstalledcorrectly.(→ page 72)

• Checktoseeiftheprojectorhasoverheated.Ifthereisinsufcientventilationaroundtheprojectororifthe

room where you are presenting is particularly warm, move the projector to a cooler location.

•

Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its life.

If so, replace the lamp. After replacing the lamp, reset the lamp hours used. (→ page 68)

• Thelampmayfailtolight.Waitafullminuteandthenturnonthepoweragain.

• Set[FANMODE]to[HIGHALTITUDE]whenusingthe projectorataltitudesapproximately5500feet/1700

meters or higher. Using the projector at altitudes approximately 5500 feet/1700 meters or higher without setting

to[HIGHALTITUDE]cancausetheprojectortooverheatandtheprojectorcouldshutdown.Ifthishappens,

wait a couple minutes and turn on the projector. (→ page 61)

If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image

for some time and then the projector will display the image. Wait for a moment.

Will turn off

• Ensurethatthe[OFFTIMER]or[AUTOPOWEROFF]isoff.(→ page 63, 64)

No picture

• UsetheCOMPUTER1,theVIDEOortheS-VIDEObuttonontheremotecontroltoselectyoursource(Com-

puter, Video or S-Video). (→ page 20) If there is still no picture, press the button again.

• Ensureyourcablesareconnectedproperly.

• Usemenustoadjustthebrightnessandcontrast.(→ page 49)

• Removethelenscap.

•

Resetthesettingsoradjustmentstofactorypresetlevelsusingthe[RESET]intheMenu.(→ page 68)

• EnteryourregisteredkeywordiftheSecurityfunctionisenabled.(→ page 32)

• BesuretoconnecttheprojectorandnotebookPCwhiletheprojectorisinstandbymodeandbeforeturning

on the power to the notebook PC.

In most cases the output signal from the notebook PC is not turned on unless connected to the projector before

being powered up.

* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver

or power management software.

• Seealsothenext page.

Picture suddenly be-

comes dark

•

Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case, lower

theinternaltemperatureoftheprojectorbyselecting[HIGH]for[FANMODE].(→ page 61)

Color tone or hue is

unusual

•

Checkifanappropriatecolorisselectedin[WALLCOLOR].Ifso,selectanappropriateoption.(→ page 55)

• Adjust[HUE]in[PICTURE].(→ page 49)

Image isn’t square to the

screen

• Repositiontheprojectortoimproveitsangletothescreen.(→ page 21)

• UsetheKeystonecorrectionfunctiontocorrectthetrapezoiddistortion.(→ page 24)

Picture is blurred

• Adjustthefocus.(→ page 23)

• Repositiontheprojectortoimproveitsangletothescreen.(→ page 21)

• Ensure that thedistance between theprojector and screenis within the adjustment rangeof the lens.

(→ page 10)

• Condensationmayformonthelensiftheprojectoriscold,broughtintoawarmplaceandisthenturnedon.

Should this happen, let the projector stand until there is no condensation on the lens.

Flicker appear s on

screen

• Set[FANMODE]tootherthan[HIGHALTITUDE]modewhenusingtheprojectorataltitudesapproximately

5500 feet/1700 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1700 meters

andsettingto[HIGHALTITUDE]cancausethelamptoovercool,causingtheimagetoicker.Switch[FAN

MODE]to[AUTO].(→ page 61)

Image is scrolling ver-

tically, horizontally or

both

• Checkthecomputer'sresolutionandfrequency.Makesurethattheresolutionyouaretryingtodisplayissup-

ported by the projector. (→ page 80)

•

AdjustthecomputerimagemanuallywiththeHorizontal/Verticalinthe[IMAGEOPTIONS].(→ page 52)

Remote control does

not work

• Installnewbatteries.(→ page 8)

• Makesuretherearenoobstaclesbetweenyouandtheprojector.

• Standwithin22feet(7m)oftheprojector.(→ page 8)

• Makesurethattheremotecontrol'sIDcorrespondswiththeprojector'sID.(→ page 60)

Indicator is lit or blink-

ing

• SeethePOWER/STATUS/LAMPIndicator.(→ page 73)

Cross color in RGB

mode

• PresstheAUTOADJ.buttonontheprojectorcabinetortheremotecontrol.(→ page 26)

• Adjustthe computerimage manuallywith[CLOCK]/[PHASE] in[IMAGEOPTIONS] inthemenu.(→ page

51)

LAN control is not ac-

tive or PC Control is not

active

• Makesurethat[CONTROLTERMINAL]issetcorrectly.(→ page 64)

Cannot control the pro-

jector from external

equipment

• Checktoseeif[STANDBYMODE]issetto[POWER-SAVING]andifitis,trytosetitto[NORMAL].(→ page

63)

3D picture is not dis-

play

• See"Troubleshootingonviewing3Dimages"onpage42.

For more information contact your dealer.

Nec np210 Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec np210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info