Bedienungsanleitung Nec np52 (Seite 86 von 100) (Englisch)

215684

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

8. Appendx

Common Problems & Solutons (→"Power/Status/LampIndicator"onpage76.)

Problem Check These Items

Does not turn on • Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control

is on. (→ page 15, 16)

• Ensure that the lamp cover is installed correctly. (

→ page 74)

• Ensure that the two screws on the lamp housing are completely tightened.(

→ page 74)

• Ensure that the cooling pump is installed correctly. (

→ page 75)

• Check to see if the projector has overheated. If there is insufﬁcient ventilation around the projector or if the room

where you are presenting is particularly warm, move the projector to a cooler location.

• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its

life. If so, replace the lamp.

After replacing the lamp, reset the lamp hours used. (

→ page 70)

• The lamp may fail to light. Wait a full minute and then turn on the power again.

• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5000 feet/1500 meters

or higher. Using the projector at altitudes approximately 5000 feet/1500 meters or higher without setting to [HIGH

ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple

minutes and turn on the projector. (→ page 65)

Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before the

projector has cooled down, the fan will run a short time before the lamp will turn on.

Will turn off • Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. (→ page 66, 67)

No picture • Use the appropriate source button on the remote control to select your source. (→ page 18) If there is still no pic-

ture, press the button again.

• Ensure your cables are connected properly.

• Use menus to adjust the contrast and brightness. (

→ page 55)

• Check to see if the image is muted. (

→ page 29)

• Remove the lens cap.

• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (

→ page 70)

• Enter your registered keyword if the SECURITY function is enabled. (

→ page 30)

• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the

power to the notebook PC.

In most cases the output signal from the notebook PC is not turned on unless connected to the projector before

being powered up.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or

power management software.

• See also the next page.

Picture suddenly becomes

dark

• When one of the following happens, the [LAMP MODE] automatically changes from [NORMAL] to [ECO].

* When there are no signals (blue or black screen) → To return to the NORMAL mode, select another available

source.

* When the room where you' re presenting is particularly warm

→ Move the projector to a cooler location.

Color tone or hue is unusu-

• Check if an appropriate color is selected in [WALL COLOR]. If not, select an appropriate option. (

→ page 61)

• Adjust [HUE] in [ADJUST]

→ [BASIC]. (→ page 55)

Image isn’t square to the

screen

• Reposition the projector to improve its angle to the screen. (

→ page 20, 21)

• Use the KEYSTONE correction function to correct the trapezoid distortion. (

→ page 25)

Picture is blurred • Make sure that focus is appropriate.

• Reposition the projector to improve its angle to the screen. (

→ page 20, 21)

• Ensure that the distance between the projector and screen is within the adjustment range of the lens. (

→ page 10)

• Make sure that the distance between the focus sensor and the screen is within the effective range of the AUTO

FOCUS. (→ page 22)

• Make sure that the requirements for the AUTO FOCUS are met. (

→ page 22)

• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

Flicker appears on screen • Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5000

feet/1500 meters or lower. Using the projector at altitudes less than approximately 5000 feet/1500 meters and setting

to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to ﬂicker. Switch [FAN MODE] to [AUTO].

(

→

page 65)

Image is scrolling verti-

cally, horizontally or both

• Use the appropriate source button on the remote control to select your source. (

→ page 18)

• Adjust the computer image manually with the [HORIZONTAL] and [VERTICAL] in [ADJUST]

→ [IMAGE OPTIONS]

in the menu. (→ page 57)

Remote control does not

work

• Install new batteries. (

→ page 8)

• Make sure there are no obstacles between you and the projector.

• Stand within 22 feet (7 m) of the projector. (

→ page 8)

Indicator is lit or blinking • See the POWER/STATUS/LAMP Indicator. (→ page 76)

Cross color in RGB mode • Press the AUTO ADJ. button on the remote control (SELECT ◀ button on the projector cabinet). (→ page 26)

• Adjust the computer image manually with [CLOCK] and [PHASE] in [ADJUST]

→ [IMAGE OPTIONS] in the menu. (→

page 56)

Formoreinformationcontactyourdealer.

Nec np52 Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec np52

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info