Bedienungsanleitung Nec P420X (Seite 210 von 222) (Englisch)

493592

210

Zoom out

Zoom in

Vorherige Seite

1/222

Nächste Seite

192

9. Appendix

1 Troubleshooting

Thissectionhelpsyouresolveproblemsyoumayencounterwhilesettinguporusingtheprojector.

Indicator Messages

Power Indicator

Indicator Condition Projector Condition Note

Off The main power is off

–

Blinking light Blue

0�5 sec On,

0�5 sec Off

The projector is getting ready to turn on� Wait for a moment�

2�5 sec On,

0�5 sec Off

Off Timer is enabled�

–

Steady light Blue The projector is turned on�

–

Orange [NORMAL] is selected for [STANDBY MODE]

–

Red [POWER-SAVING] is selected for [STANDBY

MODE]

–

Status Indicator

Indicator Condition Projector Condition Note

Off

Normal or Standby ([POWER-SAVING] for

[STANDBY MODE])

–

Blinking light Red

1 cycle (0�5 sec

On, 2�5 sec Off)

Lamp cover error or lamp housing error Replace the lamp cover or lamp housing correctly�

2 cycle (0�5 sec

On, 0�5 sec Off)

Temperature error The projector is overheated� Move the projector to

a cooler location�

3 cycle (0�5 sec

On, 0�5 sec Off)

Power error Power unit is not working properly� Contact your

dealer�

4 cycle (0�5 sec

On, 0�5 sec Off)

Fan error Fans will not work correctly�

6 cycle (0�5 sec

On, 0�5 sec Off)

Lamp error Lamp fails to light� Wait a full minute and then turn

on again�

9 cycle (0�5 sec

On, 0�5 sec Off)

[DYNAMIC CONTRAST] error Dynamic Contrast function is not working properly�

Contact your dealer�

Orange

1 cycle (0�5 sec

On, 2�5 sec Off)

Network conﬂict

Both the built-in wired LAN and the wireless LAN can-

not be connected to the same network at the same

time�

To use both built-in wired LAN and wireless LAN at

the same time, connect them to different networks�

Green Re-firing the lamp (The projector is cooling

down�)

The projector is re-ﬁring�

Wait for a moment�

Steadylight

Green

Standby ([NORMAL] for [STANDBY MODE])

–

Orange

CONTROL PANEL LOCK is on� You have pressed cabinet button when Control

Panel Lock is on�

CONTROL ID error Remote control ID and projector ID are not

matched�

Lamp Indicator

Indicator Condition Projector Condition Note

Off Normal

–

Blinking light Red

Lamp has reached its end of life� Lamp replace-

ment message will be displayed�

Replace the lamp�

Steady light Red Lamp has been used beyond its limit� The projector

will not turn on until the lamp is replaced�

Replace the lamp�

Green [ECO MODE] is set to [AUTO ECO] or [ECO1]

–

Over-Temperature Protection

Ifthetemperatureinsidetheprojectorrisestoohigh,theover-temperatureprotectorwillautomaticallyturnoffthelamp

withtheSTATUSindicatorblinking(2-cycleOnandOff.)

Shouldthishappen,dothefollowing:

• Unplugthepowercordafterthecoolingfansstop.

• Movetheprojectortoacoolerlocationiftheroomwhereyouarepresentingisparticularlytoowarm.

• Cleantheventilationholesiftheyarecloggedwithdust.

• Waitabout60minutesuntiltheinsideoftheprojectorbecomescoolenough.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec P420X Seite 210

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nec P420X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info