Bedienungsanleitung Nec vt 46 (Seite 24 von 37) (Englisch)

214394

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

E-24

Default

Returning to Factory Default [Factory Default]

The Factory Default feature allows you to change adjustments and set-

ting to the factory preset for source except the following:

Resets the adjustments for the current signal to the factory preset lev-

els.

The items that can be reset are: Brightness, Contrast, Color, Hue, Sharp-

ness, Aspect Ratio, Horizontal Position, Vertical Position, Clock, Phase

and Picture Management.

Reset all the adjustments and settings for all the signals to the factory

preset.

The items can be reset except Language, Lamp Remaining Time, Lamp

Hour Meter and Filter Usage. To reset the lamp usage time, see “Clear

Lamp Hour Meter” and “Clear Filter Usage”.

Resetting the Filter Usage Hours [Clear Filter Usage]

Resets the filter usage back to zero. Selecting this option displays

submenu for a confirmation.

Clearing Lamp Hour Meter [Clear Lamp Hour Meter]

Resets the lamp clock back to zero. Selecting this option displays

submenu for a confirmation.

NOTE: The projector will turn off and go into standby mode after 3100 hours of

service. If this happens, press and hold the ON/STAND BY and CANCEL buttons

on the remote control simultaneously for a minimum of 10 seconds to reset the

lamp clock back to zero. Do this only after replacing the lamp.

[Page 1]

Source Index

Horizontal Frequency

Vertical Frequency

Sync Polarity

[Page 2]

Signal Type

Video Type

Sync Type

Interlace

[Page 3]

Remaining Lamp Time (%)*

Lamp Hour Meter (H)

Filter Usage

Projector Usage

* The progress indicator shows the percent-

age of remaining bulb life. The value in-

forms you of the amount of lamp usage.

When the remaining lamp time reaches 0,

the Remaining Lamp Time bar indicator

changes from 0% to 100 Hours and starts

counting down.

If the remaining lamp time reaches 0 hours,

the projector will not turn on.

Enabling Auto Adjust [Auto Adjust]

When “Auto Adjust” is set to “On”, the projector automatically deter-

mines the best resolution for the current RGB input signal to project

an image using NEC’s Advanced AccuBlend Intelligent Pixel Blend-

ing Technology.

The image can be automatically adjusted for position and stability;

“Horizontal Position”, “Vertical Position”, “Clock” and “Phase”.

On .................. Automatically adjusts image “Horizontal Position”,

“Vertical Position”, “Clock” and “Phase”.

Off .................. User can adjust the image display functions (“Hori-

zontal Position”, “Vertical Position”, “Clock” and

“Phase”) manually.

NOTE: Selecting “Ceiling front” or “Ceiling rear” for “Orientation” will auto-

matically turn on this feature.

Adjusting Position/Clock (when Auto Adjust is off)

This allows you to manually adjust the image horizontally and verti-

cally, and adjust Clock and Phase.

Adjusts the image location horizontally and vertically.

This adjustment is made automatically when the Auto Adjust is turned

on.

<Clock>

Use this item with the “Auto Adjust off” to fine tune the computer

image or to remove any vertical banding that might appear. This func-

tion adjusts the clock frequencies that eliminate the horizontal band-

ing in the image. This adjustment may be necessary when you con-

nect your computer for the first time. This adjustment is made auto-

matically when the Auto Adjust is turned on.

<Phase>

Use this item to adjust the clock phase or to reduce video noise, dot

interference or cross talk. (This is evident when part of your image

appears to be shimmering.)

Use “Phase” only after the “Clock” is complete.

This adjustment is made automatically when the Auto Adjust is turned

on.

Selecting Communication Speed [Communication Speed]

This feature sets the baud rate of the PC Control port (DIN 8 Pin). It

supports data rates from 4800 to 19200 bps.

The default is 19200 bps.

Select the appropriate baud rate for your equipment to be connected

(depending on the equipment, a lower baud rate may be recommended

for long cable runs).

Information

Displays the status of the current signal and lamp usage. This item has

three pages. The information included is as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec vt 46 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info