Bedienungsanleitung Nec vt 480 (Seite 64 von 77) (Englisch)

214513

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

7. Appendix

If there is no picture, or the picture is not displayed correctly.

• Power on process for the projector and the PC.

Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on

the power to the notebook PC.

In most cases the output signal from the notebook PC is not turned on unless connected to the projector before

being powered up.

NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads

“0kHz”, this means there is no signal being output from the computer. (

→

page 47 or go to next step)

• Enabling the computer’s external display.

Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-

tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.

Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come

on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle

through external display selections.

• Non-standard signal output from the computer

If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed

correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.

Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the

previous step. Refer to your computer’s documentation for detailed information.

• Image displayed is incorrect when using a Macintosh

When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-

tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.

For setting display modes other than those supported by your Macintosh and the projector, changing the DIP

switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP

switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a

displayable mode and then restart the Macintosh again.

NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub

15-pin connector.

• Mirroring on a PowerBook

* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-

ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.

• Folders or icons are hidden on the Macintosh screen

Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple

menu and arrange icons.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec vt 480 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info