Bedienungsanleitung Nec vt 560 (Seite 29 von 42) (Englisch)

214284

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

E-29

Default

Returning to Factory Default [Factory Default]

The Factory Default feature allows you to change adjustments and set-

ting to the factory preset for source except the following:

Resets the adjustments for the current signal to the factory preset lev-

els.

The items that can be reset are: Brightness, Contrast, Color, Hue, Sharp-

ness, Aspect Ratio, Horizontal Position, Vertical Position, Clock, Phase

and Picture Management.

Reset all the adjustments and settings for all the signals to the factory

preset.

The items can be reset except Language, Security, Communication

Speed, Remaining Lamp Time, Lamp Hour Meter, Filter Usage and Pro-

jector Usage. To reset the lamp usage time, see “Clear Lamp Hour Meter”

and “Clear Filter Usage”.

Resetting the Filter Usage Hours [Clear Filter Usage]

Resets the filter usage back to zero. Selecting this option displays

submenu for a confirmation.

Clearing Lamp Hour Meter [Clear Lamp Hour Meter]

Resets the lamp clock back to zero. Selecting this option displays

submenu for a confirmation.

NOTE: The projector will turn off and go into standby mode after 2100 hours (up

to 3100 hours in Eco mode) of service. If this happens, press the “Help” button

on the remote control for ten seconds to reset the lamp clock back to zero. Do

this only after replacing the lamp.

Enabling Auto Adjust [Auto Adjust]

When “Auto Adjust” is set to “On”, the projector automatically deter-

mines the best resolution for the current RGB input signal to project

an image using NEC’s Advanced AccuBlend Intelligent Pixel Blend-

ing Technology.

The image can be automatically adjusted for position and stability;

“Horizontal Position”, “Vertical Position”, “Clock” and “Phase”.

On .................. Automatically adjusts image “Horizontal Position”,

“Vertical Position”, “Clock” and “Phase”.

Off .................. User can adjust the image display functions (“Hori-

zontal Position”, “Vertical Position”, “Clock” and

“Phase”) manually.

Adjusting Position/Clock (when Auto Adjust is off)

This allows you to manually adjust the image horizontally and verti-

cally, and adjust Clock and Phase.

Adjusts the image location horizontally and vertically.

This adjustment is made automatically when the Auto Adjust is turned

on.

<Clock>

Use this item with the “Auto Adjust off” to fine tune the computer

image or to remove any vertical banding that might appear. This func-

tion adjusts the clock frequencies that eliminate the horizontal band-

ing in the image. This adjustment may be necessary when you con-

nect your computer for the first time. This adjustment is made auto-

matically when the Auto Adjust is turned on.

<Phase>

Use this item to adjust the clock phase or to reduce video noise, dot

interference or cross talk. (This is evident when part of your image

appears to be shimmering.)

Use “Phase” only after the “Clock” is complete.

This adjustment is made automatically when the Auto Adjust is turned

on.

Selecting Communication Speed [Communication Speed]

This feature sets the baud rate of the PC Control port (DIN 8 Pin). It

supports data rates from 4800 to 19200 bps.

The default is 19200 bps.

Select the appropriate baud rate for your equipment to be connected

(depending on the equipment, a lower baud rate may be recom-

mended for long cable runs).

Information

Displays the status of the current signal and lamp usage. This item has

three pages. The information included is as follows:

[Page 1]

Source Index

Horizontal Frequency

Vertical Frequency

Sync Polarity

[Page 2]

Signal Type

Video Type

Sync Type

Interlace

[Page 3]

Remaining Lamp Time (%)*

Lamp Hour Meter (H)

Filter Usage

Projector Usage

* The progress indicator shows the

percentage of remaining bulb life.

The value informs you of the

amount of lamp usage. When the

remaining lamp time reaches 0,

the Remaining Lamp Time bar in-

dicator changes from 0% to 100

Hours and starts counting down.

If the remaining lamp time reaches

0 hours, the projector will not turn

on regardless of whether the lamp

mode is set to Normal or Eco.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nec vt 560 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info