488898
18
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
E10
Top Features
1. Power Button (ON / STAND BY) ( )
Use this button to turn the power on and off when the power is
supplied and the projector is in standby mode.
NOTE: To turn off the projector, press and hold this button
for minimum of two seconds.
2. Status Indicator
When this is lit red continually, its warning you that the
projection lamp has exceeded 1000 hours (up to 2000 hours in
Eco 2 mode and 1500 hours in Eco 1 mode) of service. After
this light appears, it is advisable to replace the projection lamp
as soon as possible. (See page E-38). In addition the message
“The lamp has reached the end of its usable life. Please re-
place the lamp.” appears each time the projector is turned on
until the lamp is replaced.
If this light blinks red rapidly, it indicates that the lamp cover
or filter cover is not attached properly or the projector is over-
heated. See the Power / Status Light Messages on page E-40
for more details.
3. Power Indicator
When this indicator is green, the projector is on; when the
indicator is orange, it is in standby mode.
4. Select (
) / (+) () Buttons
: Use these buttons to select the menu of the item you
wish to adjust.
: Use these buttons to change the level of a selected
menu item.
When an image is magnified, these buttons can be used to
move the image on screen.
5. Cancel Button
Press this button to exit the menu. While you are in the adjust-
ment or setting menu, pressing this button will return to the
previous menu.
6. Enter Button
Executes your menu selection and activates items selected from
the menu.
7. Menu Button
Displays the menu.
8. Auto Adjust Button
Use this button to adjust Position-H/V and Pixel Clock/Phase
for an optimal picture. Some signals may not be displayed
correctly or take time to switch between sources.
9. Source Button
Use this button to select a video source such as a PC, VCR or
DVD player.
Each time this button is pressed, the input source will change
as follows:
RGB Video S-Video RGB ...
If no input signal is present, the input will be skipped.
SOURCE
AUTO ADJUST
ON
STAND BY
STATUS
POWER
E
M
N
U
C
N
A
C
E
L
T
E
R
N
E
SELECT
9
3
8
74
1
2
6 5
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nec VT45 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info