Bedienungsanleitung Nedis DTCTSL50WT (Seite 4 von 28) (Alle Sprachen)

727330

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Quick start guide

Smoke alarm DTCTSL50WT

For more information see

the extended manual online:

ned.is/dtctsl50wt

Intended use

This product is intended for smoke detection. Other

uses or changes to the product constitute improper

use and carry serious risk of accidents. This product

is for indoor use only. This product is not intended

for commercial use.

The product must not be mounted in damp rooms,

near doors, windows, ventilators or radiators.

Any modication of the product may have

consequences for safety, warranty and proper

functioning.

Main parts (image A)



Smoke alarm



Indicator LED



“Test / Hush” button



Magnet



Mounting bracket



Screw (3 x 25 mm)



Plug (6 x 28 mm)

Preparation (image B - D)

Install the product on the wall or ceiling.

The product must be installed:

• In each room.

• On each oor.

• In the hallway.

• In the staircase.

• In the storage room.

• In spaces with electric equipment.

Do not install in the tip of a sloping ceiling as

smoke-free air can collect in these areas.

• Install the product on the ceiling where 1 m from

the highest point of the ceiling.

• Install the product at least 61 cm from the corner

of the wall.

• Install the product at least 50 cm from

uorescent light sources.

Installation of the product (image E)

1. Turn A

counterclockwise to remove it from

2. Remove A

from A

to switch on the

product.

3. Place A

in the desired location.

4. Use A

to mark the drill locations with a pencil.

5. Drill two Ø 6 mm holes.

6. Insert the plugs.

7. Fasten the mounting bracket with A

8. Turn A

clockwise to attach it to A

Testing the product

The product must be tested to ensure proper

operation.

1. Press and hold A

until the product emits a

continuous “beep” and A

starts blinking.

2. Release A

. The “beep” stops and A

stops

blinking.

The product is now in hush mode.

3. Repeat the above steps to exit the hush mode

and nish the test.

Hush mode

In hush mode, the product does not detect smoke

for 9 minutes.

The hush mode must be activated manually.

1. Press A

shortly to activate hush mode. The

LED blinks every 10 seconds.

After 9 minutes, the product goes back into standby

mode.

Tip: To leave the hush mode early, hold down A

until the product emits a “beep”.

Note: In hush mode, the alarm is still triggered

when the smoke concentration in the ambience

is over 4 times the minimum alarming value.

Status of smoke alarm

LED light Sound alarm

Standby mode Blinks every

344 s

O

Hush mode Blinks every

10 s

O

Test Blinks

continuously

Continuous

“beep”

Low-battery

condition

No LED

function

A “beep” every

43 s

Malfunction

or end-of-life

No LED

function

A series of

“beeps” every

43 s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nedis DTCTSL50WT Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nedis DTCTSL50WT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info