Bedienungsanleitung Nedis IRON2000 (Seite 5 von 40) (Alle Sprachen)

812860

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Spraying a burst of steam

1. Set the thermostat dial Ar to the second or third position.

2. Set the steam selector A4 to the maximum position.

3. Press the burst button A2 to spray a burst of steam.

4Wait at least 5 seconds between bursts of steam.

4Do not use the steam burst button for more than 5 consecutive

seconds.

4Hold the product vertical and use bursts of steam to remove

creases from hanging fabric.

Spraying a spray of steam

Press the spray button A3 to spray steam.

After use

1. Set the thermostat dial Ar to the minimum position.

2. Place the product on the back cover Aw.

3. Unplug the power cable A1 from the power outlet.

Troubleshooting

Problem Possible cause Possible solution

The product doesn’t

produce heat.

The thermostat

dial Ar is rotated

to OFF.

Set the thermostat

dial Ar to the

correct setting for

your fabric.

The product is not

plugged in.

Plug the power

cable A1 into a

power outlet.

The burst of steam

doesn’t function.

The burst of steam

function has been

used to often.

Continue ironing in

horizontal position

and wait a while

before using the

burst of steam

function again.

The water reservoir

A6 is empty.

Fill the water

reservoir A6 with

distilled water.

The ironing plate

A8 leaks water.

The thermostat dial

Ar is out of the

steam range.

Set the thermostat

dial Ar to the third

position.

The product has not

fully heated up yet.

Wait until the LED

indicator Ae

switches o to

indicate the product

is heated up.

The amount of

water exceeds the

MAX indicator of

the water reservoir

A6.

Pour out the excess

water from the

water reservoir A6.

The product doesn’t

produce enough

steam.

Set the steam

selector A4 to 0.

Set the steam

selector A4 to

the desired steam

output.

The steam holes

A9 are blocked.

Clean the steam

holes A9 with

distilled water.

The water reservoir

A6 is empty.

Fill the water

reservoir A6 with

distilled water.

The spray nozzle

A7 doesn’t spray.

There is not enough

pressure or air inside

of the product.

1. Push the spray

nozzle A7 by

hand.

2. Push the spray

button A3

multiple times.

Cleaning the product

Disconnect the product before cleaning.

Before cleaning and maintenance, switch o the product and

disconnect the power. Let the product cool down completely.

Do not use aggressive chemical cleaning agents such as

ammonia, acid or acetone when cleaning the product.

Do not clean the inside of the product.

Disconnect the product from the power source before service

and when replacing parts.

1. Clean the product regularly with a soft, clean, dry cloth. Avoid

abrasives that can damage the surface.

2. Clean the ironing plate A8 with a damp cloth and a non-

abrasive cleaner.

3. Clean the ironing plate A8 with a damp cloth with vinegar if

ber is stuck to the ironing plate A8.

4. Remove any limescale from the steam holes A9 with a

toothpick.

5. Empty the water reservoir A6.

4To remove all water from the water reservoir A6 and product,

connect the product to a power outlet and set the thermostat

dial Ar to the maximum position for two minutes.

4The built-in anti-scale cartridge reduces the build-up of limescale.

The built-in anti-scale cartridge does not stop the natural process

of limescale build-up.

Self-cleaning function

Use the self-cleaning function once every two weeks.

4Use distilled water.

1. Fill the measuring cup Ay with water.

2. Open the water reservoir cover A5.

3. Empty the measuring cup Ay into the water reservoir A6.

4. Close the water reservoir cover A5.

5. Place the product on the back cover Aw.

6. Plug the power cable A1 into a power outlet.

7. Set the thermostat dial Ar to the maximum position.

Wait until the LED indicator Ae switches o to indicate the product

is heated up.

8. Unplug the power cable A1 from the power outlet.

9. Hold the product horizontally above the sink.

10. Press and hold the self-cleaning button At until the water

reservoir A6 is empty.

Boiling water and steam ejects to remove the impurities from the

steam holes A9.

11. Plug the power cable A1 into a power outlet.

12. Iron an old piece of cloth to dry the ironing plate A8.

13. Unplug the power cable A1 from the power outlet.

Disposal The product is designated for separate collection at

an appropriate collection point. Do not dispose of the

product with household waste.

For more information, contact the retailer or the local

authority responsible for the waste management.

c Kurzanleitung

Dampfbügeleisen IRON2000

Weitere Informationen nden Sie in der erweiterten

Anleitung online: ned.is/iron2000

Bestimmungsgemäße Verwendung

Dieses Produkt ist ein Dampfbügeleisen, das für eine breite Auswahl

von Stoen verwendet werden kann.

Dieses Produkt ist mit einem Tropfschutzsystem ausgestattet, das

verhindert, dass Wasser aus der Bügelsohle austritt, wenn das

Produkt kalt ist.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nedis IRON2000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info