Bedienungsanleitung Neff d99w3n0 (Seite 7 von 16) (Englisch)

129383

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Cleaning and care

Isolate the extractor hood by pulling out the

mains plug or switching off the fuse.

When cleaning the grease lters, remove

grease deposits from accessible parts of the

housing. This prevents the risk of re and en-

sures that the extractor hood continues operat-

ing at maximum efciency.

Clean the extractor hood with a hot soap solu-

tion or a mild window cleaner.

Do not scrape off dried-on dirt but wipe off with

a damp cloth.

Do not use scouring agents or abrasive spong-

es.

Note: Do not use alcohol (spirit) on plastic sur-

faces, as dull marks may appear.

Caution: Ensure that the kitchen is adequately

ventilated. Avoid naked ames!

Clean the operating buttons with a mild soapy

solution and a soft, damp cloth only. Do not use

stainless-steel cleaner to clean the operating but-

tons.

Stainless steel surfaces:

Use a mild non-abrasive stainless steel cleaner.

Clean the surface in the same direction as it

has been ground and polished.

Do not use any of the following to clean stain-

less steel surfaces: abrasive sponges, cleaning

agents containing sand, soda, acid or chloride!

Aluminium and plastic surfaces:

Use a soft, non-linting window cloth or micro-

bre cloth.

Do not use dry cloths.

Use a mild window cleaning agent.

Do not use aggressive, acidic or caustic clean-

ers.

Do not use abrasive agents.

Replacing the light bulbs

1. Switch off the extractor hood and pull out the

mains plug or switch off the electricity supply at

the fuse box.

When switched on, the halogen bulbs become

very hot. Even for some time after the bulbs have

been switched off there is still a risk of burns.

2. With the aid of a screwdriver pull out the bulbs

or, if it is not easy, remove the 2 screws xing

the Lighting support, and pull it out of from the

Hood.

3. Replace the halogen light bulb (conventional

halogen bulb, 12 Volt, max. 20 Watt, GU4 bulb-

holder).

Caution: Plug-in bulbholder.

4. Replace the Support, xing it in place with the

two screws removed as above.

5. Restore the power by inserting the mains plug

or switching on the fuse.

Note: If the light does not function, check that the

bulbs have been inserted correctly.

If you encounter a problem

If you have any questions or if a fault occurs, please

call Customer Service.

(See list of Customer Service representatives).

When you call, please quote the following:

E-Nr. FD

Enter the relevant numbers into the box above. The

E-Nr. (product no.) and FD (production date) are

shown on the nameplate which can be seen inside

the extractor hood after the lter frame has been

detached.

The manufacturer of the extractor hoods

accepts no liability for complaints which can

be attributed to the design and layout of the

pipework.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Neff d99w3n0 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info