Bedienungsanleitung Neff I79MT64N1 (Seite 13 von 16) (Englisch)

633817

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

General information en

KGeneral information

General information

Exhaust air mode

:Warning

Risk of death!

Risk of poisoning from flue gases that are drawn back

in. The exhaust air must not be conveyed into a

functioning smoke or exhaust gas flue or into a shaft

which is used to ventilate installation rooms that contain

heating appliances. If the exhaust air is to be conveyed

into a non-functioning smoke or exhaust gas flue, you

must obtain the consent of the heating engineer

responsible.

If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

Note: The device manufacturer does not assume any

warranty for complaints attributable to the pipe section.

■ The device achieves its optimum performance by

means of a short, straight exhaust air pipe and as

large a pipe diameter as possible.

■ As a result of long rough exhaust air pipes, many

pipe bends or pipe diameters that are smaller than

150 mm, the optimum extraction performance is not

achieved and fan noise is increased.

■ The pipes or hoses for laying the exhaust air line

must consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the

diameter of the round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

■ Flat ducts should not have any sharp deflections.

■ Use sealing strips for deviating pipe diameters.

Preparing the ceiling

■ The ceiling must be flat, horizontal and have

adequate load-bearing capacity.

■ The depth of the bore holes must be the same

length as the screws. The wall plugs must have a

secure grip.

■ The enclosed screws and wall plugs are suitable for

solid brickwork. Suitable fasteners must be used for

other structures (e.g. plasterboard, porous concrete,

poroton bricks).

■ The max. weight of the extractor hood is 50 kg.

Electrical connection

:Warning

Risk of electric shock!

Components inside the appliance may have sharp

edges. These may damage the connecting cable. Do

not kink or pinch the connecting cable during

installation.

The required connection data can be found on the

rating plate inside the appliance; to do this, remove the

metal mesh grease filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference

suppression regulations.

:Warning

Risk of electric shock!

It must always be possible to disconnect the appliance

from the electricity supply. The appliance must only be

connected to a protective contact socket which has

been correctly installed. If the plug is no longer

accessible following installation of the appliance, or a

fixed connection is required, an all-pole isolating switch

must be present on the installation side with a contact

gap of at least 3 mm. The fixed connection must only

be installed by an electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Neff I79MT64N1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Neff I79MT64N1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info