Bedienungsanleitung Neff I89EH52N0 (Seite 12 von 16) (Englisch)

633823

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

General information

Exhaust air mode

: Risk of death!

Risk of poisoning from flue gases that are drawn back in. The

exhaust air must not be conveyed into a functioning smoke or

exhaust gas flue or into a shaft which is used to ventilate

installation rooms that contain heating appliances. If the

exhaust air is to be conveyed into a non-functioning smoke or

exhaust gas flue, you must obtain the consent of the heating

engineer responsible.

If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

Note: The appliance manufacturer does not assume any

warranty for complaints attributable to the pipe section.

■ The appliance achieves its optimum performance by means

of a short, straight exhaust air pipe and as large a pipe

diameter as possible.

■ Because of long rough exhaust air pipes, many of which are

pipe bends or have diameters smaller than 150 mm, the

optimum extraction performance is not achieved and fan

noise is increased.

■ The pipes or hoses for laying the exhaust duct must consist

of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the diameter of the

round pipes.

Ø 150 mm approx. 177 cm

Ø 120 mm approx. 113 cm

■ Flat ducts should have no sharp deflections.

■ Use sealing strip for deviating pipe diameters.

Preparing the ceiling

■ The ceiling must be flat, horizontal and have adequate load-

bearing capacity.

■ The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

■ The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other

structures (e.g. plasterboard, porous concrete, poroton

bricks).

■ The max. weight of the extractor hood is 50 kg.

Electrical connection

: Risk of electric shock!

Components inside the appliance may have sharp edges.

These may damage the connecting cable. Do not kink or pinch

the connecting cable during installation.

The required connection data can be found on the rating plate

inside the appliance; to do this, remove the metal mesh grease

filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference suppression

regulations.

: Risk of electric shock!

It must always be possible to disconnect the appliance from the

electricity supply. The appliance must only be connected to a

protective contact socket which has been correctly installed. If

the plug is no longer accessible following installation of the

appliance, or a fixed connection is required, an all-pole isolating

switch must be present on the installation side with a contact

gap of at least 3 mm. The fixed connection must only be

installed by an electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Neff I89EH52N0 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Neff I89EH52N0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info