Bedienungsanleitung Nestor Martin C15 (Seite 10 von 52) (Englisch, Französisch)

810522

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installation instructions

3.4 Flue Connection

3.4.1 General notes

This appliance may be installed with a roof terminal (C31) or a wall terminal (C11).

This appliance may only be used with Balanced Flue (otherwise known as Concentric Flue) parts as specified by

Nestor Martin. The Nestor Martin specified flue parts have been approved with the appliance. If the appliance is

installed on non- Nestor Martin approved parts, Nestor Martin cannot guarantee or accept and responsibility for

the proper and safe working of the appliance.

The flue system must be constructed from the appliance upwards, with all joints being fully locked and sealed

using the Nestor Martin specified parts.

The certified pipes to use are:

- Vertical configuration (roof) :

Pipes US 100/150 mm Metaloterm B.V. with adaptator USAK 2 10 and with the vertical roof

terminal USDVC2 10

- Horizontal configuration (wall) with vertical pipes starting from the appliance :

Pipes US 100/150 mm Metaloterm B.V. with adaptator USAK 2 10 and with the horizontal wall

terminal USDHC2 10

- Horizontal configuration (wall) starting directly from the appliance with horizontal connections :

pipes US 100/150 mm Metaloterm B.V. with adaptator USAK 2 10 and with USDSC 10 (terminal

SNORKEL)

3.4.2 Timber Frame Construction

Whilst it is possible to install room-sealed appliances in timber frame properties, great care needs to be taken to

ensure that the flue assembly does not interfere with the weather proofing qualities of any outer wall which it may

penetrate. Before attempting this work, further details need to be referenced, (e.g. “Gas Installations in Timber

Frame Buildings” from the Gas Safe installer series in the UK).

3.4.3 Carport or Building Extension

Where a flue terminal is sited within a carport or building extension, it should have at least two completely open

and unobstructed sides. The distance between the lowest part of the roof and the top of the terminal should be at

least 600mm.

Note: A covered passageway should not be treated as a carport. Flues should not be sited in a covered

passageway between properties.

3.4.4 Basements, Lightwells and Retaining walls

Flue terminals should not be sited within the confines of a basement area, light well or external space formed by

a retaining wall, unless steps are taken to ensure the products of combustion can disperse safely at all times. It

may be possible to install this Balanced Flue system in such a location provided that it is not sited lower than 1m

from the top level of that area to allow combustion products to disperse safely.

Flue terminals should be sited to ensure total clearance of the combustion products in accordance with the

included information.

When the products of combustion are discharged, they should not cause a nuisance to adjoining or adjacent

properties and they should be positioned so that damage cannot occur to other parts of the building. If the outer

wall surface is constructed of combustible material, a non-combustible plate should be fitted behind the terminal

projecting 25mm beyond the external edges of the terminal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nestor Martin C15 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nestor Martin C15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info