Bedienungsanleitung Nestor Martin FH35 (Seite 6 von 52) (Englisch, Französisch)

810527

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

User instructions

2.3 Batteries

Remote Handset:

1 x 9V "PP3" Battery, Quality alkaline recommended

Receiver:

4 x 1.5V "AA", Quality alkaline recommended for maximum life.

An alternative AC Mains Adaptor may be used to power the Receiver instead of the 4 AA batteries. Only an AC

Mains Adapter supplied by Nestor Martin may be used. The Mains Adaptor is plugged into the DC 6V socket on

the end of the receiver.

Note - if the AC Mains Adapter is used, remove the 4 AA's from the Receiver, failure to do so could result in

damage and failure of the Receiver. During a period of power outage, the receiver may be unplugged and

batteries returned to the Receiver.

2.4 Replacing the batteries

Handset:

There is a battery level indicator on the display of the handset. When this gets low remove the cover on the rear

of the handset and replace the battery with another 9V PP3 battery.

Receiver:

Three short audible beeps will sound when the appliance is on to indicate that the batteries in the receiver are

getting low.

When the batteries get very low the appliance will be turned off by the remote control. This will fail to happen if

the power supply is interrupted.

To replace the Receiver batteries, slide the cover off of the top of the receiver and use the ribbon to pull the

batteries out. Replace the batteries with new 1.5V AA's, ensuring that the ribbon is located under the batteries

and that the polarity is correct on all 4 batteries.

Never mix new batteries with old, this will result in the new batteries being emptied very quickly.

When the batteries are replaced, it may be necessary to reset the transmitter code, as detailed in the next

section.

2.5 Setting the Transmitter code

Press and hold the RESET button with a sharp object (pen or screwdriver) until you hear two audible beeps. After

the second, longer beep, release the RESET button.

Within the next twenty seconds press the down button (Button D fig 1.1) on the remote handset until you hear an

additional long signal confirming the code is set.

2.6 To Ignite the appliance

Note - If this appliance is extinguished or goes out in use for any reason, wait 3 minutes before attempting to

relight the appliance. The Gas Control Valve has an interlock device which will not allow relighting until the 3

minutes have passed.

To be able to use the Remote control Handset (fig. 1.1), the rocker switch on the Gas Valve, must be turned "ON"

(the "1" position) and the manual Dial set to the "On" position.

- Simultaneously press and hold buttons B & C (Star and Large Flame), until a short acoustic

beep confirms the start sequence has begun; release the buttons.

- Continuing signals confirm the ignition is in process.

- Once pilot ignition is confirmed, there will be gas flow and the main burner will ignite.

- Repeat process if pilot ignition fails.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nestor Martin FH35 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info