Bedienungsanleitung Nestor Martin H41 (Seite 48 von 77) (Englisch, Holländisch, Französisch)

810519

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

C07100DC023

THE FLUE

There is often confusion as to the terms “flue” and “chimney” and for the purposes of this manual we define

whatever duct conveys the products of combustion as the flue, and the term chimney to mean any masonry

structure within which the flue may be contained. It is upon the flue’s ability to provide a consistent negative

pressure or draft that the efficiency and reliability of the stove will depend and it is therefore important to

understand what can affect the flue’s performance and how to ensure the flue installation provides your stove

with the optimum operating conditions.

However well the fuel metering valve is calibrated, good combustion is dependent on the correct amount of air

being supplied to the stove at all times and this is ultimately dependent on a correct and stable negative flue

pressure. The initial flue draft is created by the gas confined within the flue being hotter and therefore lighter

than the air outside the flue. The tendency for the hot gas to move up the flue is proportional to the height of the

flue, since the difference in weight of equivalent columns of air and flue gas is greater the higher the column.

Whilst this may be theorectically true, in practice, because the temperature of the flue gas is cooled through the

wall of the flue and the flow is slowed by the friction of the internal surface of the flue, the benefits of extreme

flue heights are negated.

The need to minimise the fluctuating effects of wind by having very hot flue gas temperatures inducing the

greatest possible constant negative pressure within the flue, conflicts with the ideal of utilising all the heat

generated within the stove for heating.

The compromise is to ensure that whatever heat it is necessary to expend on creating a gas flow within the flue,

the flue makes the most efficient use of this heat by being constructed with an internal surface as smooth as

possible and by being thermally insulated. Both these requirements can be met in an existing chimney by lining it

with a stainless steel oil liner insulated with vermiculite or mineral wool, and where no chimney exists, double

walled insulated stainless steel flue systems are available.

ATMOSPHERIC INFLUENCES

Wind blowing across the flue terminal will increase the negative pressure within the flue proportionately to the

wind speed, but as wind speed is never constant the varying effect this has on the stove would be unacceptable.

To control this, the stove is fitted with a draft stabilizer. When the negative pressure approaches the desirable

upper limit the stabilizer will open, drawing air directly into the flue to supplement the flue gases coming from the

stove, thereby reducing the negative pressure to within its limits. When the wind speed decreases the stabilizer

will close to return the full negative pressure of the flue to the stove. When the stove is commissioned the

negative pressure within the stove is measured and the stabilizer is adjusted to suit the characteristics of the flue,

ensuring it gives the optimum control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nestor Martin H41 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info