Bedienungsanleitung Nestor Martin H43 (Seite 6 von 48) (Englisch, Spanisch)

571185

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

goes into the fireplace chimney. The liner of the

fireplace chimney should extend at least to the point at

which the chimney connector enters the chimney.

Follow all the guidelines for installing a chimney

connector into a freestanding masonry chimney, and

pay special attention to these additional points:

- Double check the connector clearance from

the ceiling: 18” (45 cm) minimum.

- The fireplace damper or register plate must be

closed and sealed to prevent room air from

being drawn up the flue, thereby reducing the

draft.

However, it must be possible to re-open the

damper or have an access plate in a register

plate to inspect the chimney.

2.4. Wall Pass-Throughs

Whenever possible, design your installation so that the

wall connector does not pass through a combustible

wall. If you are considering a wall pass-through in your

installation, check with your building inspector before

you begin. Also check with the chimney connector

manufacturer for any specific requirements.

Accessories are available for use as wall pass-throughs.

If using one of these, make sure it has been tested and

listed for use as a wall pass-through. We recommend

the following guidelines when passing chimney

connectors through combustible walls:

- Cut away all combustible material in the wall a

sufficient distance from the single wall connector,

to provide the required 12” (300 mm) clearance for

the connector. Any material used to close the

opening must be non-combustible (as in Fig. 5

below).

- Using a section of double-wall chimney with a 9”

(230 mm) clearance to combustibles.

- Placing a chimney connector pipe inside a

ventilated sleeve, which is then separated from

combustibles by 6” (150 mm) of fiberglass insulating

material.

Fig. 5. – An example of a correct Wall pass-through.

3. USE

Once your stove has been installed and connected to

the chimney, you are ready to light the fire.

Before lighting your stove for the first time, please take

time to become familiar with the different control

systems and parts of the unit, how to choose the wood,

how to light it and use it on a daily basis.

Ensure that the ash pan is empty.

ALWAYS KEEP IN MIND that the stove generates heat

and, therefore, keep children, clothing, furniture... at a

distance to prevent burns from direct contact with the

appliance.

Below, we have included some advice on your stove and

on its use. Please read with care.

3.1. THE WOODBOX® COMBUSTION SYSTEM

The Woodbox® system uses a balance of preheated

primary air, secondary air and natural flue draft in a

process of combustion and post-combustion, to obtain

extremely high efficiency and total controllability of the

fire.

The Woodbox® stoves, are equipped with a variable flap

mechanism to control the air intake with precision,

according to the type of combustion and the desired

tempo of the fire. The controls allow you to open these

flaps manually. An optional remote control kit allows

you to open and close these flaps automatically.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nestor Martin H43 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nestor Martin H43

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info