Bedienungsanleitung NetBotz NBWL0455 (Seite 119 von 154) (Englisch)

646452

119

Zoom out

Zoom in

Vorherige Seite

1/154

Nächste Seite

110NetBotz Appliance User’s Guide

Adding sensors to the network manually

The order in which you commission your wireless network is important.

To manually configure your wireless sensor network:

1. Connect the Coordinator to the NetBotz appliance. Note: In NetBotz v4.5, the extended address

(MAC) of the Coordinator is automatically added to the commission list.

2. Click Manual Add. In the Add Addresses dialog, scan or type the extended addresses (MAC) of

the Routers and End Devices into the commission list.

3. Click Apply Commission List to save it to the NetBotz appliance.

4. Click Configure Coordinator (Wireless Sensor Pod 180 only).

Add addresses

You can use a hand-held USB scanner with document capture capabilities to scan the MAC address bar

code on the label packaged with each USB Coordinator & Router, or the QR code on each Wireless

Temperature Sensor or Wireless Sensor Pod 180, directly into the “Add Addresses” dialog, accessed

from the Wireless Sensor Setup task in the Advanced View.

Alternatively, you can use any bar code or QR code scanner to save a list of MAC addresses to a text file

and copy and paste it into the dialog, one address per line, or enter the MAC addresses manually.

Some QR code scanners return the part number, serial number, and MAC address on one line:

XN:NBWC100U%SN:XXXXXX123456%MAC:00C0B70000XXXXXX. To add a device to your

wireless network, enter only the alphanumeric MAC address of each device in the “Add Addresses”

dialog in the Advanced View.

Once the MAC addresses have been added to the list, click Apply Commission List to save the list to

the NetBotz appliance.

Each time you add or remove extended addresses, you must apply the commission list to save the new

list to the NetBotz appliance. This does not restart the wireless network.

Configure Coordinator

You must configure the Coordinator only when Wireless Sensor Pod 180 is used as the Coordinator. To

configure the Wireless Sensor Pod 180 as the coordinator:

1. Select Configure Coordinator in the Wireless Sensor Setup window.

2. In the Serial Device Configuration window, identify the serial port ID for the sensor pod.

3. Select Wireless Sensor Pod 180 for the Device Type Installed.

4. Specify the Port Label.

5. Click OK.

The Coordinator will appear in the Alerting Sensors pane as device name C. The sensor pods in the

commission list will then join the network within one minute. Sensor pods powered by AC adapter will

join as Routers, and will appear in the Alerting Sensors pane as device name R; sensor pods powered by

batteries will join as End Devices, and will appear as device name.

Note: When you connect additional sensors to the Wireless Sensor Pod 180 devices on your wireless

network, data are reported to the Coordinator on the next data transmission cycle, not immediately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NetBotz NBWL0455 Seite 119

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info