710736
36
Zoom out
Zoom in
Vorherige Seite
1/39
Nächste Seite
Troubleshooting and Frequently Asked Questions
36
A6210 WiFi USB Adapter
Frequently Asked Questions
This section addresses the following frequently asked questions (FAQs):
Do USB Ports Go into Sleep Mode if No Traffic Is Going to or from the Port?
How Can I Improve the Speed of My WiFi Connection?
How Can I View the IP Address of the Adapter?
Do USB Ports Go into Sleep Mode if No Traffic Is Going to or
from the Port?
USB devices go into sleep mode if a Windows USB feature called Selective Suspend is
enabled, which it is by default. If your adapter or another USB device goes into Selective
Suspend mode, the network disconnects. To prevent this type of network disconnection,
disable Selective Suspend.
To disable Selective Suspend mode:
1. Select Start > Control Panel > Hardware and Sound > Power Options > Edit Plan
Settings > Change Advanced Power Settings > USB Settings.
2. Change the setting for Selective Suspend mode to Disabled.
How Can I Improve the Speed of My WiFi Connection?
The connection speed can vary depending on the type of USB port on your computer, the
capacity of the router or access point for the WiFi network, and the type of Internet
connection. You can view the physical rate in the status bar at the bottom of the NETGEAR
genie screen (for more information, see View the Connection Status and Details on page 25).
The following limits might apply:
If the physical rate is limited to 54 Mbps, the adapter might be connected to an 802.1
1a,
802.11b, or 802.11g network. If you want a faster physical rate, connect to an 802.11ac or
802.1
1n network, if available.
If the physical rate is limited to 54 Mbps, the network security might be WPA (TKIP).
When WPA (TKIP) security mode is configured on the router or access point, WiFi
regulations allow the adapter to connect at up to 54 Mbps only. For a faster connection,
configure the security for the router or access point as WPA2 or WP
A + WPA2 mixed WiFi
security
. The connection speed still
depends on the WiFi capacity of the router or access
point.
If your computer does not include a USB 3.0 or USB 2.0 port, the physical rate is limited
to the 14 Mbps of the USB 1.1 legacy standard.
How Can I View the IP Address of the Adapter?
Click the icon to open NETGEAR genie and click the Other button to view the IP
address. For more information, see View More Information About the Adapter and Network
on page 26.
36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Netgear A6210 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info