Bedienungsanleitung Netgear DGFV338 (Seite 1 von 2) (Englisch)

670580

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

)NSTALLATION'UIDE

DGFV338 ProSafe™ Wireless ADSL Modem VPN Firewall Router

Start Here

Follow these instructions to set up your wireless ADSL gateway. You can also

consult the documentation links on the Resource CD or the NETGEAR knowledgebase at

http://kbserver.netgear.com.

Prepare to Install Your Gateway

The DGFV338 ProSafe Wireless ADSL Modem VPN Firewall Router can be connected

either via an ADSL connection using the internal modem or connected using an Ethernet

connection through an external modem. Either connection is compatible with the wireless

networking bands.

First, Connect the DGFV338

1. CONNECT THE ANTENNAS TO THE DGFV338.

Attach the antennas supplied with the wireless ADSL gateway as shown in (1) and

(2).

2. CONNECT THE CABLES BETWEEN THE DGFV338, THE ISP LINE,

AND A COMPUTER

a. Connect the DGFV338 using one of the following methods:

• If you are using a direct ADSL connection, insert the telephone cable

directly into the DSL WAN port (3) of the DGFV338, or

• If you are using the Ethernet connection to an external modem, turn off and

unplug the broadband modem. Insert the Ethernet cable from the modem

into the 10/100 WAN port (4) of the DGFV338.

Note: You can connect to both WAN ports if you are planning on using the WAN

rollover feature, but not necessary otherwise.

b. Insert the Ethernet cable that came with your wireless ADSL gateway into a

LAN port on the router (5) and the other end into the Ethernet port of your

computer.

Your network cables are connected and you are ready to restart your network.

3. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE

Warning: Failure to restart your network in the correct sequence could prevent you

from connecting to the Internet.

a. First, power on the broadband modem (if required). Wait two minutes.

b. Now, power on the DGFV338 by connecting the power supply to your gateway

(6). Wait one minute.

c. Last, turn on your computer.

d. Check the DGFV338 status lights to verify the following:

• Power: The power light should turn solid green. If it does not turn solid

green, see the Troubleshooting section of the full manual.

• Test: When the router is first turned on, the test light is yellow then goes off.

After two minutes if it is still on, see the Troubleshooting Tips below.

• WAN: Either the Link/Act light on the 10/100 WAN port or the DSL light

should be lit, depending on the method of connection. If not, make sure the

Ethernet cable is securely attached to the modem and the 10/100 WAN port,

and that the modem is powered on, or that the ADSL line is securely

attached to the gateway and the ADSL outlet.

• LOCAL: A LAN light (such as 8) should be lit. Green on top indicates your

computer is communicating at 100 Mbps. If a LAN light is not lit, check that

Power

Test

Internet Ports

Local Port 8

Wireless

the Ethernet cable from the computer to the router is securely attached at

both ends, and that the computer is turned on.

Configure the DGFV338 for Internet Access

Before you begin, be sure you have the configuration parameters from your ISP handy.

1. LOG IN TO THE WIRELESS ADSL GATEWAY

Note: To connect to the firewall, your computer needs to be configured to obtain IP

addresses automatically, which is usually the case.

a. Use a browser to connect to http://192.168.1.1. For security reasons, the firewall

has its own user name and password.

When prompted, enter admin for the firewall User Name and password for the

firewall password.

b. You are now connected to the firewall.

Select Web Support on the main menu for links to the NETGEAR DGFV338

product documentation and support knowledge base. Be aware that the default

configuration login time-out is 5 minutes of inactivity, after which automatic

logout will occur.

2. CONNECT TO THE INTERNET

Configure your ISP connection for Internet access based on your WAN port

connection configuration:

a. From the Network Configuration main menu, select WAN Settings and then

select either the ADSL ISP Settings tab (for DSL) or the Ethernet ISP Settings

(for 10/100)—or configure both if you connected both WAN ports. Click Auto

Detect for the router to detect your ISP connection, or enter the parameters to

complete the Internet configuration.

b. When finished, click Test to verify that the Internet connection you selected is

active.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear DGFV338 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info