Bedienungsanleitung Netgear JNR3000 - N300 Wireless Gigabit (Seite 89 von 102) (Englisch)

479751

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

Troubleshooting

N300 Wireless Gigabit Router JNR3000

Cannot Log In to the Router

If you are unable to log in to the router from a computer on your local network, check the

following:

• If you are using an Ethernet-connected computer, check the Ethernet connection

between the computer and the router as described in the previous section.

• Make sure that your computer’s IP address is on the same subnet as the router. If you are

using the recommended addressing scheme, your computer’s address should be in the

range of 192.168.1.2 to 192.168.1.254.

• If your computer’s IP address is shown as 169.254.x.x, recent versions of Windows and

MacOS generate and assign an IP address if the computer cannot reach a DHCP server.

These auto-generated addresses are in the range of 169.254.x.x. If your IP address is in

this range, check the connection from the computer to the router, and reboot your

computer.

• If your router’s IP address was changed and you do not know the current IP address,

clear the router’s configuration to factory defaults. This sets the router’s IP address to

192.168.1.1. This procedure is explained in Factory Default Settings on page 96.

• Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using

Internet Explorer, click Refresh to be sure that the Java applet is loaded.

• Try quitting the browser and launching it again.

• Make sure that you are using the correct login information. The factory default login name

is admin, and the password is password. Make sure that Caps Lock is off when you

enter this information.

• If you are attempting to set up your NETGEAR router as an additional router behind an

existing router in your network, consider replacing the existing router instead. NETGEAR

does not support such a configuration.

• If you are attempting to set up your NETGEAR router as a replacement for an ADSL

gateway in your network, the router cannot perform many gateway services, for example,

converting ADSL or cable data into Ethernet networking information. NETGEAR does not

support such a configuration.

Cannot Access the Internet

If you can access your router but you are unable to access the Internet, first determine

whether the router can obtain an IP address from your Internet service provider (ISP). Unless

your ISP provides a fixed IP address, your router requests an IP address from the ISP. You

can determine whether the request was successful using the Router Status screen.

 To check the WAN IP address:

1. Start your browser, and select an external site such as www.netgear.com.

2. Access the router interface at www.routerlogin.net.

3. Select Adminstration > Router Status.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear JNR3000 - N300 Wireless Gigabit Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear JNR3000 - N300 Wireless Gigabit

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info