Bedienungsanleitung Netgear JWNR2000v2 (Seite 73 von 108) (Englisch)

670508

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Chapter 6. Advanced Settings | 73

NETGEAR N300 Wireless Router JWNR2000v2 User Manual

• Wireless Card Access List. For information about this list, see Restrict Wireless Access

by MAC Address on page 73.

WPS Settings

These options are available if the settings in the Wireless Settings screen are compatible with

WPS.

• Router’s PIN. The PIN is displayed so that you can use it to configure the router through

WPS (Wi-Fi Protected Setup). It is also displayed on the router’s label.

• Disable Router’s PIN. If the router’s PIN is disabled, you cannot configure the router’s

wireless settings with WPS. However, if your settings are already configured, you can still

add WPS-enabled wireless clients. The router might disable the PIN if it detects

suspicious attempts to break into your wireless settings; this can happen if the check box

is selected. You can enable the PIN by clearing the check box and clicking Apply.

• Keep Existing Wireless Settings. This check box is automatically selected after WPS is

enabled to prevent unwanted settings changes, and is also selected if you have already

specified wireless security settings or your SSID without using WPS. When this check

box is not selected, adding a new wireless client using the push button or the Add WPS

Client screen (see Wi-Fi Protected Setup (WPS) Method on page 32) changes the

router’s SSID and security passphrase. You might need to clear it if you are using certain

registrars, such as for a Windows Vista PC, to configure the router through WPS.

Wireless Card Access List

You can use this feature to restrict access by MAC address as described in the following

section.

Restrict Wireless Access by MAC Address

MAC address filtering adds an obstacle against unwanted access to your network by the

general public. However, because your trusted MAC addresses appear in your wireless

transmissions, an intruder can read them and impersonate them. Do not rely on MAC

address filtering alone to secure your network.

When a wireless card access list is configured and enabled, the router checks the MAC

address of any wireless device attempting a connection and allows only connections to

computers identified on the trusted computers list.

The Wireless Card Access List displays a list of wireless computers that you allow to connect

to the router based on their MAC addresses. These wireless computers must also have the

correct SSID and wireless security settings to access the wireless router.

The MAC address is a network device’s unique 12-character physical address, containing the

hexadecimal characters 0–9, a–f, or A–F only, and separated by colons (for example,

00:09:AB:CD:EF:01). It can usually be found on the bottom of the wireless card or network

interface device. If you do not have access to the physical label, you can display the MAC

address using the network configuration utilities of the computer. In WindowsXP, for example,

typing the

ipconfig/all command in an MSDOS command prompt window displays the

MAC address as Physical Address. You might also find the MAC addresses in the router’s

Attached Devices screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear JWNR2000v2 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear JWNR2000v2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info