479745
58
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
58 | Chapter 6: Troubleshooting
Mobile Broadband Wireless-N Router MBRN3000
If any of these conditions does not occur, refer to the following table.
Troubleshooting Access to the Router Main Menu
If you are unable to access the router main menu from a computer on your local network,
check the following:
If you are using an Ethernet-connected computer, check the Ethernet connection
between the computer and the router as described in the previous section.
Table 11. Troubleshooting with the LEDs
LED Action
Power LED is off. Make sure that the power cord is properly connected to your
router and that the power supply adapter is properly connected
to a functioning power outlet.
Check that you are using the power adapter supplied by
NETGEAR for this product.
If the error persists, you have a hardware problem and should
contact technical support.
Power LED is red There is a fault within the router. Try to clear the fault as follows:
Cycle the power to see if the router recovers.
Clear the router’s configuration to factory defaults. This sets the
router’s IP address to 192.168.0.1. This procedure is explained
in “Restoring the Default Configuration and Password” on
page 62.
If the error persists, you might have a hardware problem and should
contact technical support.
Internet LED is red. The router cannot connect to the Internet.
Make sure the USB LED is lit, indicating that the wireless modem
is securely connected to the router.
Your wireless modem must be activated and there must be
coverage in your area. To test coverage, connect your modem to
your PC, and try to connect to the Internet directly from your
computer.
Check the NETGEAR website to ensure that your wireless
modem is supported.
Close the 3G Connection manager if it is running on your PC.
LAN LEDs are off. If these LEDs do not light when the Ethernet connection is made,
check the following:
Make sure that the Ethernet cable connections are secure at the
router and at the hub or workstation.
Make sure that power is turned on to the connected hub or
workstation.
Internet LED is blinking red and
green
The traffic meter feature is enabled and the limit set has been
reached.
58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Netgear MBRN3000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Netgear MBRN3000

Netgear MBRN3000 Bedienungsanleitung - Deutsch - 6 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info