479756
106
Zoom out
Zoom in
Vorherige Seite
1/122
Nächste Seite
SM-MR814NA-0
July 2002
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Phone 1-888-NETGEAR
Reference Manual for the
Model MR814 Wireless
Router
ii
© 2002 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a trademark of Netgear, Inc.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less
than 20 cm (8 inches) during normal operation.
EN 55 022 Declaration of Conformance
This is to certify that the Model MR814 Wireless Router is shielded against the generation of radio interference in
accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application
of EN 55 022 Class B (CISPR 22).
iii
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß das Model MR814 Wireless Router gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg
46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann
jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
Certificate of the Manufacturer/Importer
It is hereby certified that the Model MR814 Wireless Router has been suppressed in accordance with the conditions set
out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test
transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes
in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the second category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read instructions for correct handling.
Customer Support
Refer to the Support Information Card that shipped with your Model MR814 Wireless Router.
World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL)
http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer
or Netscape are required.
iv
Contents v
Contents
About This Guide
Technical Support ............................................................................................................ xv
Related Publications ........................................................................................................ xv
Typographical Conventions .............................................................................................xvi
Special Message Formats ...............................................................................................xvi
Chapter 1
Introduction
About the Router ............................................................................................................1-1
Key Features ..................................................................................................................1-1
802.11b Standards-based Wireless Networking ......................................................1-2
Content Filtering .......................................................................................................1-2
Security ....................................................................................................................1-2
Autosensing 10/100 Ethernet ...................................................................................1-3
Extensive Internet Protocol Support .........................................................................1-4
Easy Installation and Management ..........................................................................1-5
Chapter 2
Setting Up the Hardware
Package Contents ..........................................................................................................2-1
Local Area Network (LAN) Hardware Requirements ......................................................2-2
Computer Requirements ..........................................................................................2-2
Access Device Requirement ....................................................................................2-2
The Router’s Front Panel ...............................................................................................2-3
The Router’s Rear Panel ................................................................................................2-4
Connecting the Router ....................................................................................................2-4
Preparing Wireless Connections ..............................................................................2-4
Connecting to Your Ethernet LAN ............................................................................2-5
Connecting to Your Internet Access Device .............................................................2-5
Connecting the Power Adapter ................................................................................2-6
Verifying Power ........................................................................................................2-6
vi Contents
Chapter 3
Preparing Your Network
Preparing Your Computers for TCP/IP Networking ........................................................3-1
Configuring Windows 95, 98, and ME for TCP/IP Networking .................................3-2
Installing or Verifying Windows Networking Components ..................................3-2
Enabling DHCP to Automatically Configure TCP/IP Settings ............................3-4
Selecting Windows’ Internet Access Method .....................................................3-4
Verifying TCP/IP Properties ...............................................................................3-5
Configuring Windows NT or 2000 for TCP/IP Networking .......................................3-5
Install or Verify Windows Networking Components ...........................................3-5
Verifying TCP/IP Properties ...............................................................................3-6
Configuring A Macintosh for TCP/IP Networking ............................................................3-6
Configuring MacOS 8.6 or 9.x for TCP/IP Networking .............................................3-7
Configuring MacOS X for TCP/IP Networking ..........................................................3-7
Verifying TCP/IP Properties for Macintosh Computers ............................................3-8
Verifying the Readiness of Your DSL or Cable Modem Internet Account .......................3-9
Are Login Protocols Used? ......................................................................................3-9
What is Your Configuration Information? .................................................................3-9
Obtaining ISP Configuration Information for Windows Computers ..................3-10
Obtaining ISP Configuration Information for Macintosh Computers ................3-11
Restarting the Network .................................................................................................3-12
Ready for Configuration ................................................................................................3-12
Chapter 4
Basic Configuration of the Router
Accessing the Web Configuration Manager ...................................................................4-1
Using the Setup Wizard ..................................................................................................4-4
Configuring Dynamic IP Accounts ............................................................................4-5
Configuring Fixed IP Accounts .................................................................................4-6
Configuring Login Accounts .....................................................................................4-7
Configuring Manually ......................................................................................................4-8
Completing the Configuration .........................................................................................4-9
Chapter 5
Wireless Configuration
Considerations For A Wireless Network .........................................................................5-1
Security ....................................................................................................................5-1
Contents vii
Placement and Range ..............................................................................................5-2
Wireless Settings ............................................................................................................5-2
Wireless Network Settings .......................................................................................5-3
Restricting Wireless Access by MAC Address .........................................................5-3
Configuring Wired Equivalent Privacy (WEP) ..........................................................5-4
Chapter 6
Content Filtering
Configuring for Content Filtering .....................................................................................6-1
Logs .........................................................................................................................6-2
Block Sites ...............................................................................................................6-3
Block Services ..........................................................................................................6-4
User Defined Service .........................................................................................6-6
IP Address Range .............................................................................................6-6
Schedule ..................................................................................................................6-7
E-Mail .......................................................................................................................6-8
Chapter 7
Maintenance
System Status .................................................................................................................7-1
Attached Devices ............................................................................................................7-4
Router Software Upgrade ...............................................................................................7-4
Configuration File Settings Management .......................................................................7-5
Restore and Backup the Configuration ....................................................................7-6
Erase the Configuration ...........................................................................................7-6
Changing the Configuration Password ...........................................................................7-7
Chapter 8
Advanced Configuration of the Router
Configuring for Port Forwarding to Local Servers ..........................................................8-2
Add a Custom Service .............................................................................................8-3
Edit or Delete a Port Forwarding Entry ....................................................................8-3
Local Web and FTP Server Example .......................................................................8-3
Setting Up Multiple Computers for Half Life, KALI or Quake III ...............................8-4
Security ...........................................................................................................................8-4
DMZ Server ..............................................................................................................8-5
Respond to Ping on Internet WAN Port ...................................................................8-6
Dynamic DNS .................................................................................................................8-6
viii Contents
LAN IP Setup ..................................................................................................................8-7
LAN TCP/IP Setup ...................................................................................................8-7
DHCP .......................................................................................................................8-9
Use Router as DHCP server .............................................................................8-9
Address Reservations .......................................................................................8-9
Static Routes ................................................................................................................8-10
Static Route Example .............................................................................................8-11
Remote Management ...................................................................................................8-12
Chapter 9
Troubleshooting
Basic Functioning ...........................................................................................................9-1
Power LED Not On ...................................................................................................9-2
Test LED Never Turns On or Test LED Stays On .....................................................9-2
LAN or WAN Port LEDs Not On ...............................................................................9-2
Troubleshooting the Web Configuration Interface ..........................................................9-3
Troubleshooting the ISP Connection ..............................................................................9-4
Troubleshooting a TCP/IP Network Using the Ping Utility ..............................................9-5
Testing the LAN Path to Your Router .......................................................................9-6
Testing the Path from Your PC to a Remote Device ................................................9-7
Restoring the Default Configuration and Password ........................................................9-7
Using the Default Reset button ................................................................................9-8
Problems with Date and Time .........................................................................................9-8
Appendix A
Technical Specifications
Appendix B
Network and Routing Basics
Basic Router Concepts .................................................................................................. B-1
What is a Router? ................................................................................................... B-1
Routing Information Protocol ................................................................................... B-2
IP Addresses and the Internet ................................................................................. B-2
Netmask .................................................................................................................. B-4
Subnet Addressing .................................................................................................. B-5
Private IP Addresses ............................................................................................... B-7
Single IP Address Operation Using NAT ................................................................. B-8
MAC Addresses and Address Resolution Protocol ................................................. B-9
Contents ix
Domain Name Server .............................................................................................. B-9
IP Configuration by DHCP .................................................................................... B-10
Wireless Networking .................................................................................................... B-10
Wireless Network Configuration ............................................................................ B-10
Ad-hoc Mode (Peer-to-Peer Workgroup) .........................................................B-11
Infrastructure Mode .........................................................................................B-11
Extended Service Set Identification (ESSID) .........................................................B-11
Authentication and WEP Encryption ..................................................................... B-12
Wireless Channel Selection .................................................................................. B-12
Ethernet Cabling .......................................................................................................... B-14
Uplink Switches, Crossover Cables, and MDI/MDIX Switching ............................ B-14
Cable Quality ......................................................................................................... B-15
Glossary
Index
x Contents
xi
Figure 2-1. MR814 Front Panel ..................................................................................2-3
Figure 2-2. MR814 Rear Panel ..................................................................................2-4
Figure 4-1. Login window ...........................................................................................4-2
Figure 4-2. Browser-based configuration main menu ................................................4-3
Figure 4-3. Setup Wizard menu for Dynamic IP address ...........................................4-5
Figure 4-4. Setup Wizard menu for Fixed IP address ................................................4-6
Figure 4-5. Setup Wizard menu for PPPoE login accounts ........................................4-7
Figure 5-1. Wireless Settings menu ...........................................................................5-2
Figure 5-2. Wireless Access List menu ......................................................................5-3
Figure 5-3. Wireless Access Setup menu ..................................................................5-4
Figure 6-1. Logs menu ...............................................................................................6-2
Figure 6-2. Block Sites menu .....................................................................................6-3
Figure 6-3. Block Services menu ...............................................................................6-4
Figure 6-4. Add Services menu ..................................................................................6-5
Figure 6-5. Schedule menu ........................................................................................6-7
Figure 6-6. Email menu ..............................................................................................6-8
Figure 7-1. System Status screen ..............................................................................7-1
Figure 7-2. Router Statistics screen ...........................................................................7-3
Figure 7-3. Attached Devices menu ...........................................................................7-4
Figure 7-4. Router Upgrade menu .............................................................................7-5
Figure 7-5. Settings Backup menu .............................................................................7-6
Figure 7-6. Set Password menu .................................................................................7-7
Figure 8-1. Port Forwarding Menu. ............................................................................8-2
Figure 8-2. Security menu. .........................................................................................8-5
Figure 8-3. LAN IP Setup Menu .................................................................................8-7
Figure 8-4. Static Route Summary Table ..................................................................8-10
Figure 8-5. Static Route Entry and Edit Menu ..........................................................8-11
Figure B-1. Three Main Address Classes .................................................................. B-3
Figure B-2. Example of Subnetting a Class B Address ............................................. B-5
Figure B-3. Single IP Address Operation Using NAT ................................................ B-8
xii
xiii
Table 2-1. LED Descriptions .....................................................................................2-3
Table 6-1. Log entry descriptions ..............................................................................6-2
Table 6-2. Log action buttons ....................................................................................6-3
Table 7-1. Menu 3.2 - System Status Fields .............................................................7-2
Table 7-2. Router Statistics Fields ...........................................................................7-3
Table B-1. Netmask Notation Translation Table for One Octet ................................. B-6
Table B-2. Netmask Formats .................................................................................... B-6
Table B-3. 802.11 Radio Frequency Channels ....................................................... B-13
Table B-4. UTP Ethernet cable wiring, straight-through ......................................... B-14
xiv
About This Guide xv
About This Guide
Congratulations on your purchase of the NETGEAR
Model MR814 Wireless Router.
The Model MR814 router provides continuous, high-speed 11 Mbps access between your wireless
and Ethernet devices. Also, the Model MR814 router enables your entire network to share an
Internet connection through a cable modem or DSL modem that otherwise is used by a single PC.
Technical Support
For help with any technical issues, contact Customer Support at 1-888-NETGEAR (in the USA &
Canada, see the Support Information Card for phone numbers in other countries), or visit us on the
Web at www.NETGEAR.com. The NETGEAR Web site includes an extensive knowledge base,
answers to frequently asked questions, and a means for submitting technical questions online.
Support is available 24 hours a day, 7 days a week.
We recommend you register your product online at: www.NETGEAR.com/register
Related Publications
As you read this document, you may be directed to various RFC documents for further
information. An RFC is a Request For Comment published by the Internet Engineering Task Force
(IETF), an open organization that defines the architecture and operation of the Internet. RFC
documents are listed on the World Wide Web at www.ietf.org and are mirrored and indexed at
many other sites worldwide.
Note: If you are unfamiliar with networking and routing, refer to Appendix B, “Network
and Routing Basics,” to become more familiar with the terms and procedures used in this
manual.
Reference Manual for the Model MR814 Wireless Router
xvi About This Guide
Typographical Conventions
This guide uses the following typographical conventions:
italics Book titles and UNIX file, command, and directory names.
courier font Screen text, user-typed command-line entries.
Initial Caps Menu titles and window and button names.
[Enter] Named keys in text are shown enclosed in square brackets. The notation
[Enter] is used for the Enter key and the Return key.
[Ctrl]+C Two or more keys that must be pressed simultaneously are shown in text
linked with a plus (+) sign.
ALL CAPS DOS file and directory names.
Special Message Formats
This guide uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Caution: This format is used to highlight information that will help you prevent
equipment failure or loss of data.
Warning: This format is used to highlight information about the possibility of injury or
equipment damage.
Danger: This format is used to alert you that there is the potential for incurring an
electrical shock if you mishandle the equipment.
Introduction 1-1
Chapter 1
Introduction
This chapter describes the features of the NETGEAR Model MR814 Wireless Router.
About the Router
The Model MR814 Wireless Router provides continuous, high-speed 11 Mbps access between
your wireless and Ethernet devices. Also, the Model MR814 router enables your entire network to
share an Internet connection through a cable modem or DSL modem that otherwise is used by a
single PC. With minimum setup, you can install and use the router within minutes.
The Model MR814 router provides multiple Web content filtering options, plus e-mail browsing
activity reporting and instant alerts. Parents and network administrators can establish restricted
access policies based on time-of-day, website addresses and address keywords, and share
high-speed cable/DSL Internet access for up to 253 personal computers. Network Address
Translation (NAT) protects you from hackers.
Key Features
The Model MR814 router provides the following features:
802.11b Standards-based wireless networking
Easy, web-based setup for installation and management
•Security
Ethernet connection to a wide area network (WAN) device, such as a cable modem or DSL
modem
Extensive Internet Protocol Support
Reference Manual for the Model MR814 Wireless Router
1-2 Introduction
These features are discussed below
802.11b Standards-based Wireless Networking
The Model MR814 router includes an 802.11b-compliant wireless access point, providing
continuous, high-speed 11 Mbps access between your wireless and Ethernet devices. The access
point provides:
802.11b Standards-based wireless networking at up to 11 Mbps
64-bit and 128-bit WEP encryption security
WEP keys can be generated manually or by passphrase
Wireless access can be restricted by MAC address.
Content Filtering
With its content filtering features, the Model MR814 router prevents objectionable content from
reaching your PCs. Its content filtering features include:
Content filtering by domain or keyword
The Model MR814 router uses content filtering to enforce your network’s Internet access
policies. The router allows you to control access to Internet content by screening for keywords
within Website names or newsgroup names.
Logging of inappropriate use
You can configure the Model MR814 router to log access to Web sites and to e-mail the log to
you. You can also configure the router to send an immediate alert e-mail message to you
whenever a local user attempts to access a blocked Web site.
Security
The Model MR814 router is equipped with several features designed to maintain security, as
described in this section.
PCs Hidden by NAT
Network address translation (NAT) opens a temporary path to the Internet for requests
originating from the local network. Requests originating from outside the LAN are discarded,
preventing users outside the LAN from finding and directly accessing the PCs on the LAN.
Reference Manual for the Model MR814 Wireless Router
Introduction 1-3
Port Forwarding with NAT
Although NAT prevents Internet locations from directly accessing the PCs on the LAN, the
router allows you to direct incoming traffic to specific PCs based on the service port number
of the incoming request, or to one designated “DMZ” host computer. You can specify
forwarding of single ports or ranges of ports.
Encryption of the Wireless Link
For security against eavesdropping of the wireless signal, the router supports Wired Equivalent
Privacy (WEP) data encryption with Shared Key authentication. You can also restrict access to
the wireless network by MAC address.
Additional security features include the following:
Parental control of web browsing and newsgroup access using Web Address (URL)
keyword blocking
Auditing and e-mail reporting of web browsing activities
Blocking can be scheduled by day and time
Network Address Translation (NAT) hides local PCs from the Internet
Incoming port forwarding and DMZ for
hosting specific Internet services without
sacrificing unauthorized access to your private network.
Autosensing 10/100 Ethernet
With its internal, 4-port 10/100 switch, the Model MR814 router can connect to either a 10 Mbps
standard Ethernet network or a 100 Mbps Fast Ethernet network. The local LAN interface is
autosensing and is capable of full-duplex or half-duplex operation.
Also, there is a built in 4-port 10/100 Mbps Switch which provides the following features:
Allows LAN connections at 10 megabits per second (Mbps) or 100 Mbps
Autosensing for Ethernet (10BASE-T) or Fast Ethernet (100BASE-Tx) transmissions
Half-duplex or full-duplex operation
Reference Manual for the Model MR814 Wireless Router
1-4 Introduction
Extensive Internet Protocol Support
The Model MR814 router supports the Transmission Control Protocol/Internet Protocol (TCP/IP)
and Routing Information Protocol (RIP).
For further information about TCP/IP, refer to Appendix B, “Network and Routing Basics.”
IP Address Sharing by NAT
The Model MR814 router allows several networked PCs to share an Internet account using
only a single IP address, which may be statically or dynamically assigned by your Internet
service provider (ISP). This technique, known as Network Address Translation (NAT), allows
the use of an inexpensive single-user ISP account.
Automatic Configuration of Attached PCs by DHCP
The Model MR814 router dynamically assigns network configuration information, including
IP, gateway, and domain name server (DNS) addresses, to attached PCs on the LAN using the
Dynamic Host Configuration Protocol (DHCP). This feature greatly simplifies configuration
of PCs on your local network.
DNS Proxy
When DHCP is enabled and no DNS addresses are specified, the router provides its own
address as a DNS server to the attached PCs. The router obtains actual DNS addresses from
the ISP during connection setup and forwards DNS requests from the LAN.
PPP over Ethernet (PPPoE)
PPP over Ethernet is a protocol for connecting remote hosts to the Internet over a DSL
connection by simulating a dial-up connection. This feature eliminates the need to run a login
program such as Enternet or WinPOET on your PC.
–IP routing
Network Address Translation (NAT) for operation with a single static or dynamic IP
address
Dynamic Host Configuration Protocol (DHCP) server for dynamically assigning
network configuration information to PCs on the LAN
DHCP client for dynamically obtaining configuration information from the Internet
Service Provider (ISP)
DNS Proxy for simplified configuration
PPP over Ethernet (PPPoE) support
Reference Manual for the Model MR814 Wireless Router
Introduction 1-5
The Model MR814 router supports login capability which automatically executes user login
for:
PPP over Ethernet (PPPoE) accounts
PPTP service (for European service providers)
BigPond service (for Telstra Australia)
Easy Installation and Management
You can install, configure, and operate the Model MR814 Wireless Router within minutes after
connecting it to the network. The following features simplify installation and management tasks:
Browser-based management
Browser-based configuration allows you to easily configure your router from almost any type
of personal computer, such as Windows, Macintosh, or Linux. A user-friendly Setup Wizard is
provided and online help documentation is built into the browser-based Web Management
Interface.
Smart Wizard
The Model MR814 router automatically senses the type of Internet connection, asking you
only for the information required for your type of ISP account.
Visual monitoring
The Model MR814 router’s front panel LEDs provide an easy way to monitor its status and
activity.
Front panel LEDs for easy monitoring of status and activity.
Flash memory for firmware upgrades.
Reference Manual for the Model MR814 Wireless Router
1-6 Introduction
Setting Up the Hardware 2-1
Chapter 2
Setting Up the Hardware
This chapter describes the Model MR814 Wireless Router hardware and provides instructions for
setting it up.
Package Contents
The product package should contain the following items:
Model MR814 Wireless Router
AC power adapter
Model MR814 Resource CD, including:
This guide
Application Notes and other helpful information
MR814 Cable/DSL Wireless Router Installation Guide
Registration and Warranty Card
Support Information Card
Vertical Stand
Keep the carton, including the original packing materials, in case you need to return the router for
repair.
Reference Manual for the Model MR814 Wireless Router
2-2 Setting Up the Hardware
Local Area Network (LAN) Hardware Requirements
The Model MR814 Wireless Router is intended for use in a network of computers that are
interconnected by 802.11b-compliant wireless adapters or twisted-pair Ethernet cables.
Computer Requirements
To install and run the Model MR814 router over your network, each computer must have the
following:
An installed 802.11b-compliant wireless adapter
OR
An Ethernet Network Interface Card (NIC).
For interconnecting your wired Ethernet devices, the Model MR814 router provides a 4-port
switch capable of either 10 Mbps or 100 Mbps operation. Links operating at 100 Mbps must
be connected with Category 5 cable.
Access Device Requirement
The cable modem or DSL modem must provide a standard 10 Mbps (10BASE-T) Ethernet
interface. The router does not support USB modems.
Reference Manual for the Model MR814 Wireless Router
Setting Up the Hardware 2-3
The Routers Front Panel
The front panel of the Model MR814 Wireless Router (Figure 2-1) contains status LEDs.
Figure 2-1. MR814 Front Panel
You can use some of the LEDs to verify connections. Table 2-1 lists and describes each LED on
the front panel of the router. These LEDs are green when lit.
Table 2-1. LED Descriptions
Label Activity Description
Power On
Off
Power is supplied to the router.
Power is not supplied to the router.
Test On
Off
The system is initializing.
The system is ready and running.
Internet On
Blink
The Internet port has detected a link with an attached device.
Data is being transmitted or received by the Internet port.
Wireless On Indicates that the Wireless port is initialized.
LAN On (Green)
Blink (Green)
On (Amber)
Blink (Amber)
Off
The Local port has detected link with a 100 Mbps device.
Data is being transmitted or received at 100 Mbps.
The Local port has detected link with a 10 Mbps device.
Data is being transmitted or received at 10 Mbps.
No link is detected on this port.
Reference Manual for the Model MR814 Wireless Router
2-4 Setting Up the Hardware
The Routers Rear Panel
The rear panel of the Model MR814 Wireless Router (Figure 2-2) contains port connections.
Figure 2-2. MR814 Rear Panel
Viewing right to left, the rear panel contains the following features:
Wireless antenna
Factory Default Reset push-button
Internet Ethernet port for connecting the router to a cable or DSL modem
Four Ethernet LAN ports for connecting the router to the local computers
AC power adapter outlet
Connecting the Router
Before using your router, you need to do the following:
Prepare your wireless devices as described below.
Connect your local Ethernet network to the LAN port(s) of the router (see page 2-5).
Connect your cable or DSL modem to the Internet port of the router (see page 2-5).
Connect the power adapter (see page 2-6)
Note: The Resource CD included with your router contains an animated Installation Assistant to
help you through this procedure.
Preparing Wireless Connections
Rotate the antenna to a vertical position.
Reference Manual for the Model MR814 Wireless Router
Setting Up the Hardware 2-5
Detailed instructions on configuring your wireless devices for TCP/IP networking are provided in
the next chapter. However, if you already have a functioning wireless network and you wish to use
a wireless PC to initially configure the router, you will need to change the settings of that PC to
match the default settings of the router:
The SSID should be Wireless (note the capitalization).
WEP encryption is disabled.
Your IP address must be in the range of 192.168.0.2 to 192.168.0.254, with a netmask of
255.255.255.0
See Chapter 5 Wireless below for full details on setting up wireless connections.
Connecting to Your Ethernet LAN
Your Ethernet network will attach to the four LAN ports on the router shown in Figure 2-2. The
LAN ports can operate at either 10 Mbps (10BASE-T) or 100 Mbps (100BASE-Tx), depending on
the Ethernet adapters in the attached computers, hub, or switch. You must use a Category 5 (CAT5)
rated Ethernet cable, such as the cable included with the router, for any connection which will
operate at 100 Mbps.
The Model MR814 router incorporates a four-port switch for connection to your local network. To
connect the router to your LAN:
Connect up to four computers directly to any of the four LAN ports of the router using
standard Ethernet cables.
To connect more than 4 computers on the Ethernet LAN, you will need to connect your router
to another hub or switch.
Connect any Local port of your router to the Uplink port of an Ethernet hub or switch
using a standard Ethernet cable.
OR
Connect any Local port of your router to any normal port of an Ethernet hub or switch
using a crossover Ethernet cable.
Connecting to Your Internet Access Device
Using the Ethernet cable already attached to your cable modem or DSL modem, connect the
routers Internet port to the Ethernet port on the modem. Turn the modem off for ten seconds, then
on again.
Reference Manual for the Model MR814 Wireless Router
2-6 Setting Up the Hardware
Note: Your cable or DSL modem must provide a standard 10BASE-T Ethernet connection for
connection to your network. The router does not support USB modems.
Note: The Ethernet cable supplied by your ISP for connecting to your cable or DSL modem may
be an Ethernet crossover cable rather than a straight-through cable. It is important to use the
existing cable to connect the modem to your router, not to connect your PCs to your router.
Connecting the Power Adapter
To connect the router to the power adapter:
1. Plug the connector of the power adapter into the power adapter outlet on the rear panel of the
router.
2. Plug the other end of the adapter into a standard wall outlet.
3. Verify that the Power LED on the router is lit.
Verifying Power
After connecting the power adapter to the router and a power source, the router powers on
automatically. Complete the following steps to verify that power is correctly applied to the router:
1. When power is first applied, verify that the Power LED comes on.
2. During the first 10 seconds, all LEDs will be tested.
3. After approximately 10 seconds, verify that:
a. The Test LED is not lit.
b. The LAN port LEDs are lit for any local ports that are connected.
c. The Internet port LED is lit.
If a port’s LED is lit, a link has been established to the connected device. If a LAN port is
connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the
LED will be amber.
You are now ready to begin configuration of your network, as described in the following chapter.
Preparing Your Network 3-1
Chapter 3
Preparing Your Network
This chapter describes how to prepare your PC network to connect to the Internet through the
Model MR814 Wireless Router and how to verify the readiness of a broadband DSL or cable
modem account from an Internet service provider (ISP).
Preparing Your Computers for TCP/IP Networking
Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/
Internet Protocol). Each computer on your network must have TCP/IP installed and selected as its
networking protocol. If a Network Interface Card (NIC) is already installed in your computer, then
TCP/IP is probably already installed as well.
Most operating systems include the software components you need for networking with TCP/IP:
Windows
®
95 or later includes the software components for establishing a TCP/IP network.
Windows 3.1 does not include a TCP/IP component. You need to purchase a third-party TCP/
IP application package such as NetManage Chameleon.
Macintosh Operating System 7 or later includes the software components for establishing a
TCP/IP network.
Note: If an ISP technician configured your PC during the installation of a broadband
modem, or if you configured it using instructions provided by your ISP, you may need to
copy the current configuration information for use in the configuration of your router.
Write down this information before reconfiguring your PCs. Refer to “Obtaining ISP
Configuration Information for Windows Computers” on page 3-10 or “Obtaining ISP
Configuration Information for Macintosh Computers” on page 3-11 for further
information.
Reference Manual for the Model MR814 Wireless Router
3-2 Preparing Your Network
All versions of UNIX or Linux include TCP/IP components. Follow the instructions provided
with your operating system or networking software to install TCP/IP on your computer.
In your TCP/IP network, each computer and the router must be assigned a unique IP addresses.
Each computer must also have other TCP/IP configuration information such as a subnet mask, a
domain name server (DNS) address, and a default gateway address. In most cases, you should
install TCP/IP so that the computer obtains its network configuration information automatically
from a DHCP server during bootup. For a detailed explanation of the meaning and purpose of
these configuration items, refer to “Appendix B, “Networks, Routing, and Firewall Basics.”
The Model MR814 router is shipped preconfigured as a DHCP server. The router assigns the
following TCP/IP configuration information automatically when the computers are rebooted:
PC, Macintosh, or workstation IP addresses—192.168.0.2 through 192.168.0.254
Subnet mask—255.255.255.0
Gateway (the router) address —192.168.0.1
Configuring Windows 95, 98, and ME for TCP/IP Networking
As part of the PC preparation process, you need to assure TCP/IP is installed and configured on
each networked PC. Before starting, locate your Windows CD which you may need to insert
during the TCP/IP installation process.
Installing or Verifying Windows Networking Components
To install or verify the necessary Windows components for TCP/IP networking follow these steps:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network icon.
The Network window opens, which displays a list of installed components:
Reference Manual for the Model MR814 Wireless Router
Preparing Your Network 3-3
You must have an Ethernet adapter, the TCP/IP protocol, and Client for Microsoft Networks.
If you need to add the adapter:
a. Click the Add button.
b. Select Adapter, and then click Add.
c. Select the manufacturer and model of your Ethernet adapter, and then click OK.
If you need TCP/IP:
a. Click the Add button.
b. Select Protocol, and then click Add.
c. Select Microsoft.
Note: It is not necessary to remove any other network components shown in the
Network window in order to install the adapter, TCP/IP, or Client for Microsoft
Networks.
Reference Manual for the Model MR814 Wireless Router
3-4 Preparing Your Network
d.
Select TCP/IP, and then click OK.
If you need Client for Microsoft Networks:
a. Click the Add button.
b. Select Client, and then click Add.
c. Select Microsoft.
d. Select Client for Microsoft Networks, and then click OK.
3. Restart your PC for the changes to take effect.
Enabling DHCP to Automatically Configure TCP/IP Settings
After the TCP/IP protocol components are installed, each PC must be assigned specific
information about itself and resources that are available on its network. The simplest way to
configure this information is to allow the PC to obtain the information from the internal DHCP
server of the Model MR814 router. To use DHCP with the recommended default addresses, follow
these steps:
1. Connect all PCs to the router, then restart the router and allow it to boot.
2. On each attached PC, open the Network control panel (refer to the previous section) and select
the Configuration tab.
3. From the components list, select TCP/IP->(your Ethernet adapter) and click Properties.
4. In the IP Address tab, select “Obtain an IP address automatically”.
5. Select the Gateway tab.
6. If any gateways are shown, remove them.
7. Click OK.
8. Restart the PC.
Repeat steps 2 through 8 for each PC on your network.
Selecting Windows’ Internet Access Method
To select Windows’ LAN Internet access method, follow these steps:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Internet Options icon.
Reference Manual for the Model MR814 Wireless Router
Preparing Your Network 3-5
3.
Select “I want to set up my Internet connection manually” or “I want to connect through a
Local Area Network” and click Next.
4. Select “I want to connect through a Local Area Network” and click Next.
5. Uncheck all boxes in the LAN Internet Configuration screen and click Next.
6. Proceed to the end of the Wizard.
Verifying TCP/IP Properties
After your PC is configured and has rebooted, you can check the TCP/IP configuration using the
utility winipcfg.exe:
1. On the Windows taskbar, click the Start button, and then click Run.
2. Type winipcfg, and then click OK.
The IP Configuration window opens, which lists (among other things), your IP address, subnet
mask, and default gateway.
3. From the drop-down box, select your Ethernet adapter.
The window is updated to show your settings, which should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends:
The IP address is between 192.168.0.2 and 192.168.0.254
The subnet mask is 255.255.255.0
The default gateway is 192.168.0.1
Configuring Windows NT or 2000 for TCP/IP Networking
As part of the PC preparation process, you need to assure TCP/IP is installed and configured on
each networked PC. Before starting, locate your Windows CD which you may need to insert
during the TCP/IP installation process.
Install or Verify Windows Networking Components
To install or verify the necessary components for IP networking:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dialup Connections icon.
Reference Manual for the Model MR814 Wireless Router
3-6 Preparing Your Network
3.
If an Ethernet adapter is present in your PC, you should see an entry for Local Area
Connection. Double-click that entry.
4. Select Properties.
5. Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If
not, select Install and add them.
6. Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address
automatically is selected.
7. Click OK and close all Network and Dialup Connections windows.
8. Make sure your PC is connected to the router, then reboot your PC.
Verifying TCP/IP Properties
To check your PC’s TCP/IP configuration:
1. On the Windows taskbar, click the Start button, and then click Run.
The Run window opens.
2. Type cmd and then click OK.
A command window opens
3. Type ipconfig /all
Your IP Configuration information will be listed, and should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends:
The IP address is between 192.168.0.2 and 192.168.0.254
The subnet mask is 255.255.255.0
The default gateway is 192.168.0.1
4. Type exit
Configuring A Macintosh for TCP/IP Networking
Beginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On
each networked Macintosh, you will need to configure TCP/IP to use DHCP.
Reference Manual for the Model MR814 Wireless Router
Preparing Your Network 3-7
Configuring MacOS 8.6 or 9.x for TCP/IP Networking
1. From the Apple menu, select Control Panels, then TCP/IP.
The TCP/IP Control Panel opens:
2. From the “Connect via” box, select your Macintosh’s Ethernet interface.
3. From the “Configure” box, select Using DHCP Server.
You can leave the DHCP Client ID box empty.
4. Close the TCP/IP Control Panel.
5. Repeat this for each Macintosh on your network.
Configuring MacOS X for TCP/IP Networking
1. From the Apple menu, choose System Preferences, then Network.
2. If not already selected, select Built-in Ethernet in the Configure list.
3. If not already selected, select Using DHCP in the TCP/IP tab.
4. Click Save.
Reference Manual for the Model MR814 Wireless Router
3-8 Preparing Your Network
Verifying TCP/IP Properties for Macintosh Computers
After your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by
returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.
The panel is updated to show your settings, which should match the values below if you are using
the default TCP/IP settings that NETGEAR recommends:
The IP Address is between 192.168.0.2 and 192.168.0.254
The Subnet mask is 255.255.255.0
The Router address is 192.168.0.1
If you do not see these values, you may need to restart your Macintosh or you may need to switch
the “Configure” setting to a different option, then back again to “Using DHCP Server”.
Reference Manual for the Model MR814 Wireless Router
Preparing Your Network 3-9
Verifying the Readiness of Your DSL or Cable Modem
Internet Account
For access to the Internet, you need to contract with an Internet service provider (ISP) for a
single-user Internet access account using a cable modem or DSL modem. This modem must be a
separate physical box (not a card) and must provide an Ethernet port intended for connection to a
Network Interface Card (NIC) in a computer. Your router does not support a USB-connected
broadband modem.
For a single-user Internet account, your ISP supplies TCP/IP configuration information for one
PC. With a typical account, much of the configuration information is dynamically assigned when
your PC is first booted up while connected to the ISP, and you will not need to know that dynamic
information.
In order to share the Internet connection among several computers, your router takes the place of
the single PC. You need to configure the router with the TCP/IP information that the single PC
would normally use. When the router is connected to the broadband modem, the router appears to
be a single PC to the ISP. The router then allows multiple computers on the local network to
masquerade as the single PC to access the Internet through the broadband modem.
Are Login Protocols Used?
Some ISPs require a special login protocol, in which you must enter a login name and password in
order to access the Internet. If you normally log in to your Internet account by running a program
such as WinPOET or EnterNet, then your account uses PPP over Ethernet (PPPoE).
When you configure your router, you will need to enter your login name and password in the
router’s configuration menus. After your network and router are configured, the router will
perform the login task when needed, and you will no longer need to run the login program from
your PC. It is not necessary to uninstall the login program.
What is Your Configuration Information?
More and more, ISPs are dynamically assigning configuration information. However, if your ISP
does not dynamically assign configuration information but instead used fixed configurations, your
ISP should have given you the following basic information for your account:
Reference Manual for the Model MR814 Wireless Router
3-10 Preparing Your Network
An IP address and subnet mask
A gateway IP address, which is the address of the ISPs router
One or more domain name server (DNS) IP addresses
Host name and domain suffix
For example, your account’s full server names may look like this:
mail.xxx.yyy.com
In this example, the domain suffix is
xxx.yyy.com.
If any of these items are dynamically supplied by the ISP, your router automatically acquires them.
If an ISP technician configured your PC during the installation of the broadband modem, or if you
configured it using instructions provided by your ISP, you need to copy the configuration
information from your PC’s Network TCP/IP Properties window or Macintosh TCP/IP Control
Panel before reconfiguring your PC for use with the router. These procedures are described next.
Obtaining ISP Configuration Information for Windows Computers
As mentioned above, you may need to collect configuration information from your PC so that you
can use this information when you configure the Model MR814 router. Following this procedure is
only necessary when your ISP does not dynamically supply the account information.
To get the information you need to configure the router for Internet access:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network icon.
The Network window opens, which displays a list of installed components.
3. Select TCP/IP, and then click Properties.
The TCP/IP Properties dialog box opens.
4. Select the IP Address tab.
If an IP address and subnet mask are shown, write down the information. If an address is
present, your account uses a fixed (static) IP address. If no address is present, your account
uses a dynamically-assigned IP address. Click “Obtain an IP address automatically”.
5. Select the Gateway tab.
If an IP address appears under Installed Gateways, write down the address. This is the ISP’s
gateway address. Select the address and then click Remove to remove the gateway address.
Reference Manual for the Model MR814 Wireless Router
Preparing Your Network 3-11
6.
Select the DNS Configuration tab.
If any DNS server addresses are shown, write down the addresses. If any information appears
in the Host or Domain information box, write it down. Click Disable DNS.
7. Click OK to save your changes and close the TCP/IP Properties dialog box.
You are returned to the Network window.
8. Click OK.
9. Reboot your PC at the prompt. You may also be prompted to insert your Windows CD.
Obtaining ISP Configuration Information for Macintosh Computers
As mentioned above, you may need to collect configuration information from your Macintosh so
that you can use this information when you configure the Model MR814 router. Following this
procedure is only necessary when your ISP does not dynamically supply the account information.
To get the information you need to configure the router for Internet access:
1. From the Apple menu, select Control Panels, then TCP/IP.
The TCP/IP Control Panel opens, which displays a list of configuration settings. If the
“Configure” setting is “Using DHCP Server”, your account uses a dynamically-assigned IP
address. In this case, close the Control Panel and skip the rest of this section.
2. If an IP address and subnet mask are shown, write down the information.
3. If an IP address appears under Router address, write down the address. This is the ISP’s
gateway address.
4. If any Name Server addresses are shown, write down the addresses. These are your ISP’s DNS
addresses.
5. If any information appears in the Search domains information box, write it down.
6. Change the “Configure” setting to “Using DHCP Server”.
7. Close the TCP/IP Control Panel.
Reference Manual for the Model MR814 Wireless Router
3-12 Preparing Your Network
Restarting the Network
Once you’ve set up your computers to work with the router, you must reset the network for the
devices to be able to communicate correctly.
1. Turn off the DSL or cable modem, wait 15 seconds, and then turn it on again
2. Turn off the router, and then turn it on again and wait about 10 seconds until the Test light
turns off.
3. Restart any computer that is connected to the router.
Note: If the modem doesn’t have an on/off switch pull the modem’s power adapter out of the wall
socket or power strip.
Ready for Configuration
After configuring all of your computers for TCP/IP networking and connecting them to the local
network of your Model MR814 router, you are ready to access and configure the router. Proceed to
the next chapter.
Basic Configuration of the Router 4-1
Chapter 4
Basic Configuration of the Router
This chapter describes how to perform the basic configuration of your Model MR814 Wireless
Router using the Setup Wizard, which walks you through the configuration process for your
Internet connection.
Accessing the Web Configuration Manager
In order to use the browser-based Web Configuration Manager, your PC must have a web browser
program installed such as Microsoft Internet Explorer or Netscape Navigator. Because the
Configuration Manager uses Java, your Web browser must be Java-enabled and support HTTP
uploads. NETGEAR recommends using Microsoft Internet Explorer 5.0 or Netscape Navigator
4.7 or above. Free browser programs are readily available for Windows, Macintosh, or UNIX/
Linux.
To configure for Internet access using your browser:
1. Turn on the router and wait for initialization to complete.
Allow at least ten seconds and verify that the Test LED is off.
2. Reboot your computer to obtain DHCP configuration from the router.
3. Launch your web browser.
Note: If you normally use a login program such as Enternet or WinPOET to access the
Internet, do not launch that program.
4. Click your browser’s Stop button.
5. In the Address or Location box of your browser, type http://192.168.0.1 and press ENTER.
Reference Manual for the Model MR814 Wireless Router
4-2 Basic Configuration of the Router
A login window opens as shown in Figure 4-1 below:.
Figure 4-1. Login window
This screen may have a different appearance in other browsers.
6. Type admin in the User Name box, password in the Password box, and then click OK. The
User Name and Password are case sensitive.
If your router password was previously changed, enter the current password.
If your router has not yet been configured, the Setup Wizard should launch automatically.
Otherwise, the main menu of the Web Configuration Manager will appear as shown in Figure 4-2
below:
Reference Manual for the Model MR814 Wireless Router
Basic Configuration of the Router 4-3
Figure 4-2. Browser-based configuration main menu
You can manually configure your router using this menu as described in “Configuring Manually“
on page 4-8, or you can allow the Setup Wizard to determine your configuration as described in the
following chapter.
Reference Manual for the Model MR814 Wireless Router
4-4 Basic Configuration of the Router
Using the Setup Wizard
The Web Configuration Manager contains a Setup Wizard that can automatically determine your
network connection type. If the Setup Wizard does not launch automatically, click on the Setup
Wizard heading in the upper left of the opening screen, shown in Figure 4-2.
When the Wizard launches, allow the router to automatically determine your connection type by
selecting Yes in the menu below and clicking Next:
The Setup Wizard will now check for a connection on the Internet port. If the Setup Wizard
determines that there is no connection to the Internet port, you will be prompted to check the
physical connection between your router and cable or DSL modem. When the connection is
properly made, the router’s Internet LED should be on.
Next, the Setup Wizard will attempt to determine which of the following connection types
your Internet service account uses:
Dynamic IP assignment
Fixed IP address assignment
A login protocol such as PPPoE
The Setup Wizard will report which connection type it has discovered, and it will then use the
appropriate configuration menu for that connection type.
Reference Manual for the Model MR814 Wireless Router
Basic Configuration of the Router 4-5
Configuring Dynamic IP Accounts
If the Setup Wizard determines that your Internet service account uses Dynamic IP assignment via
DHCP, you will be directed to the menu shown in Figure 4-3 below:
Figure 4-3. Setup Wizard menu for Dynamic IP address
1.
Enter your Account Name (may also be called Host Name) and Domain Name. These
parameters may be necessary to access your ISP’s services such as mail or news servers. If you
leave the Domain Name field blank, the router will attempt to learn the domain automatically
from the ISP. If this is not successful, you may need to enter it manually.
2. Domain Name Server (DNS) Address: If you know that your ISP does not automatically
transmit DNS addresses to the router during login, select “Use these DNS servers” and enter
the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is
available, enter it also.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically your ISP transfers the IP addresses of one or
two DNS servers to your router during login. If the ISP does not transfer an address, you
must obtain it from the ISP and enter it manually here. If you enter an address here, you
should reboot the computers on your network after configuring the router.
Reference Manual for the Model MR814 Wireless Router
4-6 Basic Configuration of the Router
3.
Router’s MAC Address: This section determines the Ethernet MAC address that will be used
by the router on the Internet port. If your ISP allows access by only one specific PC’s Ethernet
MAC address, select "Use this MAC address." The router will then capture and use the MAC
address of the PC that you are now using. You must be using the one PC that is allowed by the
ISP.
Some ISPs will register the Ethernet MAC address of the network interface card in your
PC when your account is first opened. They will then only accept traffic from the MAC
address of that PC. This feature allows your router to masquerade as that PC by using its
MAC address.
4. Click on Apply, then proceed to “Completing the Configuration“ on page 4-9.
Configuring Fixed IP Accounts
If the Setup Wizard determines that your Internet service account uses Fixed IP assignment, you
will be directed to the menu shown in Figure 4-4 below:
Figure 4-4. Setup Wizard menu for Fixed IP address
1.
Enter your assigned IP Address, Subnet Mask, and the IP Address of your ISP’s gateway
router. This information should have been provided to you by your ISP.
2. Domain Name Server (DNS) Address: If you know that your ISP does not automatically
transmit DNS addresses to the router during login, select “Use these DNS servers” and enter
the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is
available, enter it also.
Reference Manual for the Model MR814 Wireless Router
Basic Configuration of the Router 4-7
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically your ISP transfers the IP addresses of one or
two DNS servers to your router during login. If the ISP does not transfer an address, you
must obtain it from the ISP and enter it manually here. If you enter an address here, you
should reboot your PCs after configuring the router.
3. Click on Apply, then proceed to “Completing the Configuration“ on page 4-9.
Configuring Login Accounts
If the Setup Wizard determines that your Internet service account uses a login protocol such as
PPP over Ethernet (PPPoE), you will be directed to a menu like the PPPoE menu shown in
Figure 4-5 below:
Figure 4-5. Setup Wizard menu for PPPoE login accounts
1.
Enter your Account Name (may also be called Host Name) and Domain Name. These
parameters may be necessary to access your ISP’s services such as mail or news servers. If you
leave the Domain Name field blank, the router will attempt to learn the domain automatically
from the ISP. If this is not successful, you will need to enter it manually.
2. Enter the PPPoE login user name and password provided by your ISP. These fields are case
sensitive. If you wish to change the login time-out, enter a new value in minutes.
Reference Manual for the Model MR814 Wireless Router
4-8 Basic Configuration of the Router
Note: You will no longer need to launch the ISP’s login program on your PC in order to access
the Internet. When you start an Internet application, your router will automatically log you in.
3. Domain Name Server (DNS) Address: If you know that your ISP does not automatically
transmit DNS addresses to the router during login, select “Use these DNS servers” and enter
the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is
available, enter it also.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically your ISP transfers the IP addresses of one or
two DNS servers to your router during login. If the ISP does not transfer an address, you
must obtain it from the ISP and enter it manually here. If you enter an address here, you
should reboot your PCs after configuring the router.
4. Click on Apply, then proceed to “Completing the Configuration“ on page 4-9.
Configuring Manually
You can manually configure the router in the Basic Settings menu shown in Figure 4-2 using these
steps:
1. Select whether your Internet connection requires a login.
Select ‘Yes’ if you normally must launch a login program such as Enternet or WinPOET in
order to access the Internet.
2. Enter your Account Name (may also be called Host Name) and Domain Name. These
parameters may be necessary to access your ISP’s services such as mail or news servers.
3. (If displayed) Enter the PPPoE login user name and password provided by your ISP. These
fields are case sensitive. If you wish to change the login time-out, enter a new value in
minutes.
Note: You will no longer need to launch the ISP’s login program on your PC in order to access
the Internet. When you start an Internet application, your router will automatically log you in.
4. Internet IP Address: If your ISP has assigned you a permanent, fixed (static) IP address for
your PC our router, select “Use static IP address”. Enter the IP address that your router has
been assigned. Also enter the netmask and the Gateway IP address. The Gateway is the ISP’s
router to which your router will connect.
Reference Manual for the Model MR814 Wireless Router
Basic Configuration of the Router 4-9
5.
Domain Name Server (DNS) Address: If you know that your ISP does not automatically
transmit DNS addresses to the router during login, select “Use these DNS servers” and enter
the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is
available, enter it also.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically your ISP transfers the IP addresses of one or
two DNS servers to your router during login. If the ISP does not transfer an address, you
must obtain it from the ISP and enter it manually here. If you enter an address here, you
should reboot your PCs after configuring the router.
6. Router’s MAC Address: This section determines the Ethernet MAC address that will be used
by the router on the Internet port. Some ISPs will register the Ethernet MAC address of the
network interface card in your PC when your account is first opened. They will then only
accept traffic from the MAC address of that PC. This feature allows your router to masquerade
as that PC by “cloning” its MAC address. You can specify the MAC address in one of two
ways:
a. Select "Use this Computers MAC address." The router will then capture and use the
MAC address of the PC that you are now using. You must be using the one PC that is
allowed by the ISP.
b. Select "Use this MAC address" and manually enter the MAC address you wish to use.
7. Click on Apply, then proceed to “Completing the Configuration“ on page 4-9.
Completing the Configuration
Click on the Test button to test your Internet connection. If the NETGEAR website does not
appear within one minute, refer to Chapter 9, “Troubleshooting”.
Your router is now configured to provide Internet access for your network. When your router and
PCs are configured correctly, your router automatically accesses the Internet when one of your
LAN devices requires access. It is not necessary to run a dialer or login application such as
Dial-Up Networking or Enternet to connect, log in, or disconnect. These functions are performed
by the router as needed.
To access the Internet from any PC connected to your router, launch a browser such as Microsoft
Internet Explorer or Netscape Navigator. You should see the routers Internet LED blink,
indicating communication to the ISP. The browser should begin to display a Web page.
The following chapters describe how to configure the Advanced features of your router, and how
to troubleshoot problems that may occur.
Reference Manual for the Model MR814 Wireless Router
4-10 Basic Configuration of the Router
Wireless Configuration 5-1
Chapter 5
Wireless Configuration
This chapter describes how to configure the wireless features of your Model MR814 Wireless
Router.
Considerations For A Wireless Network
In planning your wireless network, you should consider the level of security required. You should
also select the physical placement of your router in order to maximize the network speed. For
further information on wireless networking, refer to “Wireless Networking” in Appendix B,
“Network and Routing Basics.”
Security
Unlike wired network data, your wireless data transmissions can extend beyond your walls and
can be received by anyone with a compatible adapter. For this reason, NETGEAR strongly
recommends that you make use of the security features of your wireless equipment. As a minimum
security precaution, you should change the SSID setting of all devices on your network from the
factory setting to a unique password. Restricting access by MAC address filtering adds another
obstacle against unwanted hosts joining your network. To hinder a determined eavesdropper, you
should enable Wired Equivalent Privacy (WEP) data encryption. However, there may be a
significant degradation of the data throughput on the wireless link when WEP is enabled.
Note: If you are configuring the router from a wireless PC and you change the router’s
SSID, channel, or WEP settings, you will lose your wireless connection when you click
on Apply. You must then change the wireless settings of your PC to match the router’s
new settings.
Reference Manual for the Model MR814 Wireless Router
5-2 Wireless Configuration
Placement and Range
The operating distance or range of your wireless connection can vary significantly based on the
physical placement of the wireless router. For best results, place your router:
near the center of the area in which your PCs will operate,
in an elevated location such as a high shelf,
away from potential sources of interference, such as PCs, microwaves, and cordless phones,
away from large metal surfaces.
Wireless Settings
To configure the Wireless interface of your router, click on the Wireless heading in the Main Menu
of the browser interface. The Wireless Settings menu will appear, as shown in Figure 5-1:
Figure 5-1. Wireless Settings menu
Reference Manual for the Model MR814 Wireless Router
Wireless Configuration 5-3
Wireless Network Settings
In the Wireless Network section are the following parameters:
SSID (Service Set ID)
Enter a value of up to 32 alphanumeric characters. The same SSID must be assigned to all
wireless devices in your network. The default SSID is Wireless, but NETGEAR strongly
recommends that you change your network’s SSID to a different value.
•Region
This field displays the region of operation for which the wireless interface is intended. It may
not be legal to operate the router in a region other than the region shown here.
Channel
This field determines which operating frequency will be used. It should not be necessary to
change the wireless channel unless you notice interference problems with another nearby
access point.
Be sure to click Apply to save any settings from this menu.
Restricting Wireless Access by MAC Address
By default, any wireless PC that is configured with the correct SSID will be allowed access to your
wireless network. For increased security, you can restrict access to the wireless network to only
allow specific PCs based on their MAC addresses. From the Wireless Settings menu, click the
Setup Access List button to display the Wireless Access List menu, shown in Figure 5-2:
Figure 5-2. Wireless Access List menu
Reference Manual for the Model MR814 Wireless Router
5-4 Wireless Configuration
The Wireless Access window displays a list of MAC addresses that will be allowed to connect to
the router. These PCs must also have the correct SSID and WEP settings. To restrict access based
on MAC addresses:
1. Click the Add button to go to the Add/Edit menu shown in Figure 5-3:
Figure 5-3. Wireless Access Setup menu
For your convenience, this menu displays a list of currently active wireless cards and their
Ethernet MAC addresses.
2. If the desired PC appears in the list, you can click on it to capture its MAC address; otherwise,
you can manually enter the MAC address of the authorized PC.
The MAC address is usually printed on the wireless card.
3. If no Device Name appears, you can type a descriptive name for the PC that you are adding.
4. Click Add.
5. When you have finished entering MAC addresses, return to the Wireless Access List menu
and check the Turn Access Control On box, then click Apply.
To edit a MAC address from the table, click on it to select it, then click the Edit or Delete button.
Configuring Wired Equivalent Privacy (WEP)
In the Wireless Settings menu you can configure WEP data encryption using the following
parameters:
Reference Manual for the Model MR814 Wireless Router
Wireless Configuration 5-5
Authentication Type
Normally this can be left at the default value of "Automatic." If that fails, select the
appropriate value - "Open System" or "Shared Key." Check your wireless card's
documentation to see what method to use.
Encryption Strength
Select the WEP Encryption level:
Off - no data encryption (Open System)
64-bit (sometimes called 40-bit) encryption
128-bit encryption
•Keys
If WEP is enabled, you can manually or automatically program the four data encryption keys.
These values must be identical on all PCs and Access Points in your network.
Automatic - Enter a word or group of printable characters in the Passphrase box and click
the Generate button. The four key boxes will be automatically populated with key values.
Manual - Enter ten hexadecimal digits (any combination of 0-9, a-f, or A-F)
Select which of the four keys will be active.
Be sure to click Apply to save your settings in this menu.
Reference Manual for the Model MR814 Wireless Router
5-6 Wireless Configuration
Content Filtering 6-1
Chapter 6
Content Filtering
This chapter describes how to use the Content Filtering features of your Model MR814 Wireless
Router. These features can be found by clicking on the Content Filtering heading in the Main
Menu of the browser interface.
Configuring for Content Filtering
The Model MR814 Wireless Router provides you with Web content filtering options, plus
browsing activity reporting and instant alerts via e-mail. Parents and network administrators can
establish restricted access policies based on time-of-day, web addresses and web address
keywords. You can also block Internet access by applications and services, such as chat or games.
To configure these features of your router, click on the subheadings under the Content Filtering
heading in the Main Menu of the browser interface. The subheadings are described below:
Reference Manual for the Model MR814 Wireless Router
6-2 Content Filtering
Logs
The log is a detailed record of what websites you have accessed or attempted to access. Up to 128
entries are stored in the log. Log entries will only appear when keyword blocking is enabled, and
no log entries will be made for the Trusted User. An example is shown in Figure 6-1 below:
Figure 6-1. Logs menu
Log entries are described in Table 6-1
Table 6-1. Log entry descriptions
Field Description
Number The index number of the content filter log entries. 128 entries
are available numbered from 0 to 127. The log will keep the
record of the latest 128 entries.
Date and Time The date and time the log entry was recorded.
Source IP The IP address of the initiating device for this log entry.
Action This field displays whether the access was blocked or allowed.
The name or IP address of the website or newsgroup visited or
attempted to access.
Reference Manual for the Model MR814 Wireless Router
Content Filtering 6-3
Log action buttons are described in Table 6-2
Block Sites
The Model MR814 router allows you to restrict access based on web addresses and web address
keywords. Up to 255 entries are supported in the Keyword list. The Block Sites menu is shown in
Figure 6-2 below:
Figure 6-2. Block Sites menu
Table 6-2. Log action buttons
Field Description
Refresh Click this button to refresh the log screen.
Clear Log Click this button to clear the log entries.
Send Log
Click this button to email the log immediately.
Reference Manual for the Model MR814 Wireless Router
6-4 Content Filtering
To enable keyword blocking, select either “Per Schedule” or “Always”, then click Apply. If you
want to block by schedule, be sure that a time period is specified in the Schedule menu.
To add a keyword or domain, type it in the Keyword box, click Add Keyword, then click Apply.
To delete a keyword or domain, select it from the list, click Delete Keyword, then click Apply.
Keyword application examples:
If the keyword "XXX" is specified, the URL <http://www.badstuff.com/xxx.html> is blocked.
If the keyword “.com” is specified, only websites with other domain suffixes (such as .edu or
.gov) can be viewed.
If you wish to block all Internet browsing access during a scheduled period, enter the keyword
“.” and set the schedule in the Schedule menu.
To specify a Trusted User, enter that PC’s IP address in the Trusted User box and click Apply.
You may specify one Trusted User, which is a PC that will be exempt from blocking and
logging. Since the Trusted User will be identified by an IP address, you should configure that
PC with a fixed IP address.
Block Services
The Model MR814 router allows you to block the use of certain Internet services by PCs on your
network. This is called services blocking or port filtering. The Block Services menu is shown in
Figure 6-3 below:
Figure 6-3. Block Services menu
Reference Manual for the Model MR814 Wireless Router
Content Filtering 6-5
Services are functions performed by server computers at the request of client computers. For
example, Web servers serve web pages, time servers serve time and date information, and game
hosts serve data about other players’ moves. When a computer on your network sends a request for
service to a server computer on the Internet, the requested service is identified by a service or port
number. This number appears as the destination port number in the transmitted IP packets. For
example, a packet that is sent with destination port number 80 is an HTTP (Web server) request.
To enable service blocking, select either “Per Schedule” or “Always”, then click Apply. If you
want to block by schedule, be sure that a time period is specified in the Schedule menu.
To specify a service for blocking, click Add. The Add Services menu will appear, as shown in
Figure 6-4 below:
Figure 6-4. Add Services menu
From the Service Type list, select the application or service to be allowed or blocked. The list
already displays several common services, but you are not limited to these choices. To add any
additional services or applications that do not already appear, select User Defined.
Reference Manual for the Model MR814 Wireless Router
6-6 Content Filtering
User Defined Service
To define a service, first you must determine which port number or range of numbers is used by
the application. The service numbers for many common protocols are defined by the Internet
Engineering Task Force (IETF) and published in RFC1700, “Assigned Numbers.” Service
numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of
the application. This information can usually be determined by contacting the publisher of the
application or from user groups of newsgroups.
Enter the Starting Port and Ending Port numbers. If the application uses a single port number, enter
that number in both boxes.
If you know that the application uses either TCP or UDP, select the appropriate protocol. If you are
not sure, select Both.
IP Address Range
Under “Filter IP”, you can block the specified service for a single PC, a range of PCs (having
consecutive IP addresses), or all PCs on your network.
Reference Manual for the Model MR814 Wireless Router
Content Filtering 6-7
Schedule
The Model MR814 router allows you to specify when blocking will be enforced. The Schedule
menu is shown in Figure 6-5 below:
Figure 6-5. Schedule menu
Use this schedule for blocking content
Check this box if you wish to enable a schedule for Content Filtering. Click Apply.
•Days to Block
Select days to block by checking the appropriate boxes. Select Everyday to check the boxes
for all days. Click Apply.
Time of Day to Block
Select a start and end time in 23:59 format. Select All day for 24 hour blocking. Click Apply.
Be sure to select your Time Zone in the E-Mail menu.
Reference Manual for the Model MR814 Wireless Router
6-8 Content Filtering
E-Mail
In order to receive logs and alerts by email, you must provide your email information in the E-Mail
menu, shown in Figure 6-6 below:
Figure 6-6. Email menu
Turn e-mail notification on
Check this box if you wish to receive e-mail logs and alerts from the router.
Your outgoing mail server
Enter the name of your ISP’s outgoing (SMTP) mail server (such as mail.myISP.com). You
may be able to find this information in the configuration menu of your e-mail program. If you
leave this box blank, log and alert messages will not be sent via e-mail.
Send to this e-mail address
Enter the e-mail address to which logs and alerts are sent. This e-mail address will also be used
as the From address. If you leave this box blank, log and alert messages will not be sent via
e-mail.
Reference Manual for the Model MR814 Wireless Router
Content Filtering 6-9
You can specify that logs are automatically sent to the specified e-mail address with these options:
Send alert immediately
Check this box if you would like immediate notification of attempted access to a blocked site.
Send logs according to this schedule
Specifies how often to send the logs: Hourly, Daily, Weekly, or When Full.
Day for sending log
Specifies which day of the week to send the log. Relevant when the log is sent weekly or
daily.
Time for sending log
Specifies the time of day to send the log. Relevant when the log is sent daily or weekly.
If the Weekly, Daily or Hourly option is selected and the log fills up before the specified
period, the log is automatically e-mailed to the specified e-mail address. After the log is sent,
the log is cleared from the router’s memory. If the router cannot e-mail the log file, the log
buffer may fill up. In this case, the router overwrites the log and discards its contents.
The Model MR814 router uses the Network Time Protocol (NTP) to obtain the current time and
date from one of several Network Time Servers on the Internet. In order to localize the time for
your log entries, you must specify your Time Zone:
•Time Zone
Select your local time zone. This setting will be used for the blocking schedule and for
time-stamping log entries.
Daylight Savings Time
Check this box if your time zone is currently under daylight savings time.
Reference Manual for the Model MR814 Wireless Router
6-10 Content Filtering
Maintenance 7-1
Chapter 7
Maintenance
This chapter describes how to use the maintenance features of your Model MR814 Wireless
Router. These features can be found by clicking on the Maintenance heading in the Main Menu of
the browser interface.
System Status
The System Status menu provides a limited amount of status and usage information. From the
Main Menu of the browser interface, click on Maintenance, then select System Status to view the
System Status screen, shown in Figure 7-1.
Figure 7-1. System Status screen
Reference Manual for the Model MR814 Wireless Router
7-2 Maintenance
This screen shows the following parameters:
Table 7-1. Menu 3.2 - System Status Fields
Field Description
System Name This field displays the Host Name assigned to the router.
Firmware Version This field displays the router firmware version.
Internet Port These parameters apply to the Internet (WAN) port of the router.
MAC Address This field displays the Ethernet MAC address being used by the Internet
(WAN) port of the router.
IP Address This field displays the IP address being used by the Internet (WAN) port
of the router. If no address is shown, the router cannot connect to the
Internet.
IP Subnet Mask This field displays the IP Subnet Mask being used by the Internet (WAN)
port of the router.
DHCP If set to None, the router is configured to use a fixed IP address on the
WAN.
If set to Client, the router is configured to obtain an IP address
dynamically from the ISP.
LAN Port These parameters apply to the Local (WAN) port of the router.
MAC Address This field displays the Ethernet MAC address being used by the Local
(LAN) port of the router.
IP Address This field displays the IP address being used by the Local (LAN) port of
the router. The default is 192.168.0.1
IP Subnet Mask This field displays the IP Subnet Mask being used by the Local (LAN)
port of the router. The default is 255.255.255.0
DHCP If set to None, the router will not assign IP addresses to local PCs on the
LAN.
If set to Server, the router is configured to assign IP addresses to local
PCs on the LAN.
Wireless Port These parameters apply to the Wireless port of the router.
MAC (BSS ID) This field displays the Ethernet MAC address being used by the
Wireless Port. This will be the same MAC address as the Local (LAN)
port of the router.
Region This field displays the region of legal operation for the wireless interface.
Reference Manual for the Model MR814 Wireless Router
Maintenance 7-3
Click on the “Show Statistics” button to display router usage statistics, as shown in Figure 7-2
below:
Figure 7-2. Router Statistics screen
This screen shows the following statistics:.
Click on the “Connections Status” button to display details about the WAN connection, such as the
progress of the PPPoE connection.
Table 7-2. Router Statistics Fields
Field Description
Port The statistics for the WAN (Internet) and LAN (local) ports. For each port, the screen
displays:
Status The link status of the port.
TxPkts The number of packets transmitted on this port since reset or manual clear.
RxPkts The number of packets received on this port since reset or manual clear.
Collisions The number of collisions on this port since reset or manual clear.
Tx B/s The current line utilization—percentage of current bandwidth used on this port.
Tx B/s The average line utilization —average CLU for this port.
Up Time The time elapsed since this port acquired link.
System up Time The time elapsed since the last power cycle or reset.
Poll Interval Specifies the intervals at which the statistics are updated in this window. Click on Stop
to freeze the display.
Reference Manual for the Model MR814 Wireless Router
7-4 Maintenance
Attached Devices
The Attached Devices menu contains a table of all IP devices that the router has discovered on the
local network. From the Main Menu of the browser interface, under the Maintenance heading,
select Attached Devices to view the table, shown in Figure 7-3
Figure 7-3. Attached Devices menu
For each device, the table shows the IP address, NetBIOS Host Name (if available), and Ethernet
MAC address. Note that if the router is rebooted, the table data is lost until the router rediscovers
the devices. To force the router to look for attached devices, click the Refresh button.
Router Software Upgrade
The routing software of the Model MR814 router is stored in FLASH memory, and can be
upgraded as new software is released by NETGEAR. Upgrade files can be downloaded from
Netgear's website. If the upgrade file is compressed (.ZIP file), you must first extract the binary
(.BIN) file before sending it to the router. The upgrade file can be sent to the router using your
browser.
Note: The Web browser used to upload new firmware into the Model MR814 router must support
HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer 5.0 or Netscape
Navigator 4.7 or above.
Reference Manual for the Model MR814 Wireless Router
Maintenance 7-5
From the Main Menu of the browser interface, under the Maintenance heading, select the Router
Upgrade heading to display the menu shown in Figure 7-4.
Figure 7-4. Router Upgrade menu
To upload new firmware:
1. Download and unzip the new software file from NETGEAR.
2. In the Router Upgrade menu, click the Browse button and browse to the location of the binary
(.BIN) upgrade file
3. Click Upload.
Note: When uploading software to the Model MR814 router, it is important not to interrupt the
Web browser by closing the window, clicking a link, or loading a new page. If the browser is
interrupted, it may corrupt the software. When the upload is complete, your router will
automatically restart. The upgrade process will typically take about one minute.
In some cases, you may need to reconfigure the router after upgrading.
Configuration File Settings Management
The configuration settings of the Model MR814 router are stored within the router in a
configuration file. This file can be saved (backed up) to a users PC, retrieved (restored) from the
users PC, or cleared to factory default settings.
Reference Manual for the Model MR814 Wireless Router
7-6 Maintenance
From the Main Menu of the browser interface, under the Maintenance heading, select the Settings
Backup heading to bring up the menu shown in Figure 7-5.
Figure 7-5. Settings Backup menu
Three options are available, and are described in the following sections.
Restore and Backup the Configuration
The Restore and Backup options in the Settings Backup menu allow you to save and retrieve a file
containing your router’s configuration settings.
To save your settings, select the Backup tab. Click the Backup button. Your browser will extract
the configuration file from the router and will prompt you for a location on your PC to store the
file. You can give the file a meaningful name at this time, such as pacbell.cfg.
To restore your settings from a saved configuration file, enter the full path to the file on your PC or
click the Browse button to browse to the file. When you have located it, click the Restore button to
send the file to the router. The router will then reboot automatically.
Erase the Configuration
It is sometimes desirable to restore the router to a known blank condition. This can be done by
using the Erase function, which will restore all factory settings. After an erase, the router's
password will be password, the LAN IP address will be 192.168.0.1, and the router's DHCP client
will be enabled.
Reference Manual for the Model MR814 Wireless Router
Maintenance 7-7
To erase the configuration, click the Erase button.
To restore the factory default configuration settings without knowing the login password or IP
address, you must use the Default Reset button on the rear panel of the router. See “Using the
Default Reset button“ on page 9-8.
Changing the Configuration Password
The default password for the routers Web Configuration Manager is password. Netgear
recommends that you change this password to a more secure password.
From the Main Menu of the browser interface, under the Maintenance heading, select Set
Password to bring up the menu shown in Figure 7-6.
Figure 7-6. Set Password menu
To change the password, first enter the old password, and then enter the new password twice. Click
Apply.
Reference Manual for the Model MR814 Wireless Router
7-8 Maintenance
Advanced Configuration of the Router 8-1
Chapter 8
Advanced Configuration of the Router
This chapter describes how to configure the advanced features of your Model MR814 Wireless
Router. These features can be found under the Advanced heading in the Main Menu of the browser
interface.
Reference Manual for the Model MR814 Wireless Router
8-2 Advanced Configuration of the Router
Configuring for Port Forwarding to Local Servers
Although the router causes your entire local network to appear as a single machine to the Internet,
you can make a local server (for example, a web server or game server) visible and available to the
Internet. This is done using the Port Forwarding menu. From the Main Menu of the browser
interface, under Advanced, click on Port Forwarding to view the port forwarding menu, shown in
Figure 8-1
Figure 8-1. Port Forwarding Menu.
Use the Port Forwarding menu to configure the router to forward incoming protocols to computers
on your local network. In addition to servers for specific applications, you can also specify a
Default DMZ Server to which all other incoming protocols are forwarded. The DMZ Server is
configured in the Security Menu.
Before starting, you'll need to determine which type of service, application or game you'll provide
and the IP address of the computer that will provide each service. Be sure the computers IP
address never changes. To configure port forwarding to a local server:
1. From the Service & Game box, select the service that you will host on your network. If the
service does not appear in the list, refer to the following section, “Add a Custom Service”.
2. Enter the IP address of the local server in the corresponding Server IP Address box.
3. Click the Add button.
Note: Some residential broadband ISP accounts do not allow you to run any server
processes (such as a Web or FTP server) from your location. Your ISP may periodically
check for servers and may suspend your account if it discovers any active services at
your location. If you are unsure, refer to the Acceptable Use Policy of your ISP.
Reference Manual for the Model MR814 Wireless Router
Advanced Configuration of the Router 8-3
Add a Custom Service
To define a service, game or application that does not appear in the Services & Games list, you
must determine what port numbers are used by the service. For this information, you may need to
contact the manufacturer of the program that you wish to use. For more information on service
ports, see “Block Services“ on page 6-4. When you have the port number information, follow
these steps:
1. Click the Add Custom Service button.
2. Enter the first port number in an unused Start Port box.
3. To forward only one port, enter it again in the End Port box. To specify a range of ports, enter
the last port to be forwarded in the End Port box.
4. Enter the IP address of the local server in the corresponding Server IP Address box.
5. Type a name for the service.
6. Click Apply at the bottom of the menu.
Edit or Delete a Port Forwarding Entry
To edit or delete a Port Forwarding entry, follow these steps.
1. In the table, select the button next to the service name.
2. Click Edit or Delete.
Local Web and FTP Server Example
If a local PC with a private IP address of 192.168.0.33 acts as a Web and FTP server, configure the
Ports menu to forward HTTP (port 80) and FTP (port 21) to local address 192.168.0.33
In order for a remote user to access this server from the Internet, the remote user must know the IP
address that has been assigned by your ISP. If this address is 172.16.1.23, for example, an Internet
user can access your Web server by directing the browser to http://172.16.1.23. The assigned IP
address can be found in the Maintenance Status Menu, where it is shown as the WAN IP Address.
Some considerations for this application are:
If your account’s IP address is assigned dynamically by your ISP, the IP address may change
periodically as the DHCP lease expires.
Reference Manual for the Model MR814 Wireless Router
8-4 Advanced Configuration of the Router
If the IP address of the local PC is assigned by DHCP, it may change when the PC is rebooted.
To avoid this, use the Address Reservations feature in the LAN IP menu to make sure the local
PC always receives the same IP address.
Local PCs must access the local server by its local LAN address (192.168.0.33 in this
example). Attempts by local PCs to access the server using the external IP address
(172.16.1.23 in this example) will fail.
Setting Up Multiple Computers for Half Life, KALI or Quake III
To set up an additional computer to play Half Life, KALI or Quake III:
1. Click the button of an unused port in the table.
2. Select the game again from the Services/Games list.
3. Change the beginning port number in the Start Port box.
For these games, use the supplied number in the default listing and add +1 for each additional
computer. For example, if you've already configured one computer to play Hexen II (using
port 26900), the second computer's port number would be 26901, and the third computer
would be 26902.
4. Type the same port number in the End Port box that you typed in the Start Port box.
5. Type the IP address of the additional computer in the Server IP Address box.
6. Click Apply.
Some online games and videoconferencing applications are incompatible with NAT. The Model
MR814 router is programmed to recognize some of these applications and to work properly with
them, but there are other applications that may not function well. In some cases, one local PC can
run the application properly if that PC’s IP address is entered as the default in the PORTS Menu. If
one local PC acts as a game or videoconference host, enter its IP address as the default.
Security
The security area lets you configure a DMZ server for hosting specific Internet services without
sacrificing unauthorized access to your private network. Also, in this area, you can enable
the Internet port to respond to PING requests. Setting up these features is described below
Reference Manual for the Model MR814 Wireless Router
Advanced Configuration of the Router 8-5
DMZ Server
Incoming traffic from the Internet is normally discarded by the router unless the traffic is a
response to one of your local computers or a service that you have configured in the Port
Forwarding menu. Instead of discarding this traffic, you can have it forwarded to one computer on
your network. This computer is called the Default DMZ Server.
The Default DMZ Server feature is helpful when using some online games and videoconferencing
applications that are incompatible with NAT. The router is programmed to recognize some of these
applications and to work properly with them, but there are other applications that may not function
well. In some cases, one local PC can run the application properly if that PC’s IP address is entered
as the Default DMZ Server.
The Security menu, shown in Figure 8-2, allows the configuration of a Default DMZ Server.
Figure 8-2. Security menu.
To assign a computer or server to be a Default DMZ server:
1. Click Default DMZ Server.
2. Type the IP address for that server.
3. Click Apply.
Note: For security, you should avoid using the Default DMZ Server feature. When a
computer is designated as the Default DMZ Server, it loses much of the protection of the
router, and is exposed to many exploits from the Internet. If compromised, the computer
can be used to attack your network.
Reference Manual for the Model MR814 Wireless Router
8-6 Advanced Configuration of the Router
Respond to Ping on Internet WAN Port
If you want the router to respond to a 'ping' from the Internet, click the ‘Respond to Ping on
Internet WAN Port’ check box. This should only be used as a diagnostic tool, since it allows your
router to be discovered. Don't check this box unless you have a specific reason to do so.
Dynamic DNS
If your network has a permanently assigned IP address, you can register a domain name and have
that name linked with your IP address by public Domain Name Servers (DNS). However, if your
Internet account uses a dynamically assigned IP address, you will not know in advance what your
IP address will be, and the address can change frequently. In this case, you can use a commercial
dynamic DNS service, who will allow you to register your domain to their IP address, and will
forward traffic directed at your domain to your frequently-changing IP address.
The router contains a client that can connect to many popular dynamic DNS services. You can
select one of these services and obtain an account with them. Then, whenever your ISP-assigned
IP address changes, your router will automatically contact your dynamic DNS service provider,
log in to your account, and register your new IP address.
From the Main Menu of the browser interface, under Advanced, click on Dynamic DNS. To
configure Dynamic DNS:
1. Access the website of one of the dynamic DNS service providers whose names appear in the
‘Select Service Provider’ box, and register for an account.
For example, for dyndns.org, go to www.dyndns.org.
2. Select the Use a dynamic DNS service check box.
3. Select the name of your dynamic DNS Service Provider.
4. Type the Host Name that your dynamic DNS service provider gave you.
The dynamic DNS service provider may call this the domain name.
5. Type the User Name for your dynamic DNS account.
6. Type the Password (or key) for your dynamic DNS account.
7. If your dynamic DNS provider allows the use of wildcards in resolving your URL, you may
select the Use wildcards check box to activate this feature.
For example, the wildcard feature will cause *.yourhost.dyndns.org to be aliased to the same
IP address as yourhost.dyndns.org
Reference Manual for the Model MR814 Wireless Router
Advanced Configuration of the Router 8-7
8.
Click Apply to save your configuration.
LAN IP Setup
The second feature category under the Advanced heading is LAN IP Setup. This menu allows
configuration of LAN IP services such as DHCP and RIP. From the Main Menu of the browser
interface, under Advanced, click on LAN IP Setup to view the LAN IP Setup menu, shown in
Figure 8-3
Figure 8-3. LAN IP Setup Menu
LAN TCP/IP Setup
The router is shipped preconfigured to use private IP addresses on the LAN side, and to act.as a
DHCP server. The routers default LAN IP configuration is:
Note: If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x),
the dynamic DNS service will not work because private addresses will not be routed on
the Internet.
Reference Manual for the Model MR814 Wireless Router
8-8 Advanced Configuration of the Router
LAN IP addresses—192.168.0.1
Subnet mask—255.255.255.0
These addresses are part of the IETF-designated private address range for use in private networks,
and should be suitable in most applications. If your network has a requirement to use a different IP
addressing scheme, you can make those changes in this menu.
The LAN IP parameters are:
IP Address
This is the LAN IP address of the router.
IP Subnet Mask
This is the LAN Subnet Mask of the router. Combined with the IP address, the IP Subnet Mask
allows a device to know which other addresses are local to it, and which must be reached
through a gateway or router.
RIP Direction
RIP (Router Information Protocol) allows a router to exchange routing information with other
routers. The RIP Direction selection controls how the router sends and receives RIP packets.
Both is the default.
When set to Both or Out Only, the router will broadcast its routing table periodically.
When set to Both or In Only, it will incorporate the RIP information that it receives.
When set to None, it will not send any RIP packets and will ignore any RIP packets
received.
RIP Version
This controls the format and the broadcasting method of the RIP packets that the router sends.
(It recognizes both formats when receiving.) By default, this is set for RIP-1.
RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you
have an unusual network setup.
RIP-2 carries more information. RIP-2B uses subnet broadcasting..
Note: If you change the LAN IP address of the router while connected through the
browser, you will be disconnected. You must then open a new connection to the new IP
address and log in again.
Reference Manual for the Model MR814 Wireless Router
Advanced Configuration of the Router 8-9
DHCP
By default, the router will function as a DHCP (Dynamic Host Configuration Protocol) server,
allowing it to assign IP, DNS server, and default gateway addresses to all computers connected to
the router's LAN. The assigned default gateway address is the LAN address of the router. IP
addresses will be assigned to the attached PCs from a pool of addresses specified in this menu.
Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.
For most applications, the default DHCP and TCP/IP settings of the router are satisfactory. See “IP
Configuration by DHCP” on page B-10 for an explanation of DHCP and information about how to
assign IP addresses for your network.
Use Router as DHCP server
If another device on your network will be the DHCP server, or if you will manually configure the
network settings of all of your computers, clear the ‘Use router as DHCP server’ check box.
Otherwise, leave it checked.
Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP
Address. These addresses should be part of the same IP address subnet as the router’s LAN IP
address. Using the default addressing scheme, you should define a range between 192.168.0.2 and
192.168.0.253, although you may wish to save part of the range for devices with fixed addresses.
The router will deliver the following parameters to any LAN device that requests DHCP:
An IP Address from the range you have defined
Subnet Mask
Gateway IP Address (the router’s LAN IP address)
Primary DNS Server (if you entered a Primary DNS address in the Basic Settings menu;
otherwise, the router’s LAN IP address)
Secondary DNS Server (if you entered a Secondary DNS address in the Basic Settings menu
Address Reservations
When you specify a reserved IP address for a PC on the LAN, that PC will always receive the
same IP address each time it access the router’s DHCP server. Reserved IP addresses should be
assigned to servers that require permanent IP settings.
To reserve an IP address:
Reference Manual for the Model MR814 Wireless Router
8-10 Advanced Configuration of the Router
1.
Click the Add button.
2. In the IP Address box, type the IP address to assign to the PC or server.
(choose an IP address from the router’s LAN subnet, such as 192.168.0.X)
3. Type the MAC Address of the PC or server.
(Tip: If the PC is already present on your network, you can copy its MAC address from the
Attached Devices menu and paste it here.)
4. Click Apply to enter the reserved address into the table.
Note: The reserved address will not be assigned until the next time the PC contacts the router's
DHCP server. Reboot the PC or access its IP configuration and force a DHCP release and renew.
To edit or delete a reserved address entry:
1. Click the button next to the reserved address you want to edit or delete.
2. Click Edit or Delete.
Static Routes
Static Routes provide additional routing information to your router. Under normal circumstances,
the router has adequate routing information after it has been configured for Internet access, and
you do not need to configure additional static routes. You must configure static routes only for
unusual cases such as multiple routers or multiple IP subnets located on your network.
From the Main Menu of the browser interface, under Advanced, click on Static Routes to view the
Static Route menu, shown in Figure 8-4.
Figure 8-4. Static Route Summary Table
To add or edit a Static Route:
Reference Manual for the Model MR814 Wireless Router
Advanced Configuration of the Router 8-11
1.
Click the Add button to open the Add/Edit Menu, shown in Figure 8-5.
Figure 8-5. Static Route Entry and Edit Menu
2.
Type a route name for this static route in the Route Name box under the table.
(This is for identification purpose only.)
3. Select Private if you want to limit access to the LAN only. The static route will not be reported
in RIP.
4. Select Active to make this route effective.
5. Type the Destination IP Address of the final destination.
6. Type the IP Subnet Mask for this destination.
If the destination is a single host, type 255.255.255.255.
7. Type the Gateway IP Address, which must be a router on the same LAN segment as the router.
8. Type a number between 1 and 15 as the Metric value.
This represents the number of routers between your network and the destination. Usually, a
setting of 2 or 3 works, but if this is a direct connection, set it to 1.
9. Click Apply to have the static route entered into the table.
Static Route Example
As an example of when a static route is needed, consider the following case:
Your primary Internet access is through a cable modem to an ISP.
Reference Manual for the Model MR814 Wireless Router
8-12 Advanced Configuration of the Router
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is 192.168.0.100.
Your companys network is 134.177.0.0.
When you first configured your router, two implicit static routes were created. A default route was
created with your ISP as the gateway, and a second static route was created to your local network
for all 192.168.0.x addresses. With this configuration, if you attempt to access a device on the
134.177.0.0 network, your router will forward your request to the ISP. The ISP forwards your
request to the company where you are employed, and the request will likely be denied by the
companys firewall.
In this case you must define a static route, telling your router that 134.177.0.0 should be accessed
through the ISDN router at 192.168.0.100. The static route would look like Figure 8-5.
In this example:
The Destination IP Address and IP Subnet Mask fields specify that this static route applies to
all 134.177.x.x addresses.
The Gateway IP Address fields specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.0.100.
A Metric value of 1 will work since the ISDN router is on the LAN.
Private is selected only as a precautionary security measure in case RIP is activated.
Remote Management
Using the Remote Management page, you can allow a user or users on the Internet to configure,
upgrade and check the status of your Model MR814 router.
To configure your router for Remote Management:
1. Select the Turn Remote Management On check box.
Note: Be sure to change the router's default configuration password to a very secure
password. The ideal password should contain no dictionary words from any language,
and should be a mixture of letters (both upper and lower case), numbers, and symbols.
Your password can be up to 30 characters.
Reference Manual for the Model MR814 Wireless Router
Advanced Configuration of the Router 8-13
2.
Specify what external addresses will be allowed to access the router’s remote management.
For security, NETGEAR recommends that you restrict access to as few external IP addresses
as practical.
a. To allow access from any IP address on the Internet, select Everyone.
b. To allow access from a range of IP addresses on the Internet, select IP address range.
Enter a beginning and ending IP address to define the allowed range.
c. To allow access from a single IP address on the Internet, select Only this PC.
Enter the IP address that will be allowed access.
3. Specify the Port Number that will be used for accessing the management interface.
Web browser access normally uses the standard HTTP service port 80. For greater security,
you can change the remote management web interface to a custom port by entering that
number in the box provided. Choose a number between 1024 and 65535, but do not use the
number of any common service port. The default is 8080, which is a common alternate for
HTTP.
4. Click Apply to have your changes take effect.
When accessing your router from the Internet, you will type your router's WAN IP address into
your browser's Address (in IE) or Location (in Netscape) box, followed by a colon (:) and the
custom port number. For example, if your external address is 134.177.0.123 and you use port
number 8080, enter in your browser:
http://134.177.0.123:8080
Reference Manual for the Model MR814 Wireless Router
8-14 Advanced Configuration of the Router
Troubleshooting 9-1
Chapter 9
Troubleshooting
This chapter gives information about troubleshooting your Model MR814 Wireless Router. After
each problem description, instructions are provided to help you diagnose and solve the problem.
For the common problems listed, go to the section indicated.
Is the router on?
Have I connected the router correctly?
Go to “Basic Functioning“ on page 9-1.
I can’t access the router’s configuration with my browser.
Go to “Troubleshooting the Web Configuration Interface“ on page 9-3.
I’ve configured the router but I can’t access the Internet.
Go to “Troubleshooting the ISP Connection“ on page 9-4.
I can’t remember the router’s configuration password.
I want to clear the configuration and start over again.
Go to “Restoring the Default Configuration and Password“ on page 9-7.
Basic Functioning
After you turn on power to the router, the following sequence of events should occur:
1. When power is first applied, verify that the Power LED is on.
2. Verify that the Test LED lights within a few seconds, indicating that the self-test
procedure is running.
3. After approximately 10 seconds, verify that:
a. The Test LED is not lit.
Reference Manual for the Model MR814 Wireless Router
9-2 Troubleshooting
b. The LAN port LEDs are lit for any local ports that are connected.
c. The WAN port LED is lit.
If a port’s LED is lit, a link has been established to the connected device. If a LAN port is
connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the
LED will be amber.
If any of these conditions does not occur, refer to the appropriate following section.
Power LED Not On
If the Power and other LEDs are off when your router is turned on:
Make sure that the power cord is properly connected to your router and that the power supply
adapter is properly connected to a functioning power outlet.
Check that you are using the 12 V DC power adapter supplied by NETGEAR for this product.
If the error persists, you have a hardware problem and should contact technical support.
Test LED Never Turns On or Test LED Stays On
When the router is turned on, the Test LED turns on for about 10 seconds and then turns off. If the
Test LED does not turn on, or if it stays on, there is a fault within the router.
If you experience problems with the Test LED:
Cycle the power to see if the router recovers and the LED blinks for the correct amount of
time.
If all LEDs including the Test LED are still on one minute after power up:
Cycle the power to see if the router recovers.
Clear the routers configuration to factory defaults. This will set the routers IP address to
192.168.0.1. This procedure is explained in “Using the Default Reset button“ on page 9-8.
If the error persists, you might have a hardware problem and should contact technical support.
LAN or WAN Port LEDs Not On
If either the LAN LEDs or WAN LED do not light when the Ethernet connection is made, check
the following:
Reference Manual for the Model MR814 Wireless Router
Troubleshooting 9-3
Make sure that the Ethernet cable connections are secure at the router and at the hub or
workstation.
Make sure that power is turned on to the connected hub or workstation.
Be sure you are using the correct cable:
When connecting the router’s WAN port to a cable or DSL modem, use the cable that was
supplied with the cable or DSL modem. This cable could be a standard straight-through
Ethernet cable or an Ethernet crossover cable.
Troubleshooting the Web Configuration Interface
If you are unable to access the router’s Web Configuration interface from a PC on your local
network, check the following:
If you are using an Ethernet-connected PC, check the Ethernet connection between the PC and
the router as described in the previous section.
If you are using a wireless-connected PC, that the SSID and WEP settings are the same for the
router and PC. The routers default settings are: SSID is Wireless and WEP is disabled.
Make sure your PC’s IP address is on the same subnet as the router. If you are using the
recommended addressing scheme, your PC’s address should be in the range of 192.168.0.2 to
192.168.0.254. Refer to “Verifying TCP/IP Properties“ on page 3-5 or Verifying TCP/IP
Properties for Macintosh Computers“ on page 3-8 to find your PC’s IP address. Follow the
instructions in Chapter 3 to configure your PC.
Note: If your PC’s IP address is shown as 169.254.x.x:
Recent versions of Windows and MacOS will generate and assign an IP address if the
computer cannot reach a DHCP server. These auto-generated addresses are in the range of
169.254.x.x. If your IP address is in this range, check the connection from the PC to the router
and reboot your PC.
If your router’s IP address has been changed and you don’t know the current IP address, clear
the routers configuration to factory defaults. This will set the router’s IP address to
192.168.0.1. This procedure is explained in “Using the Default Reset button“ on page 9-8.
Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet
Explorer, click Refresh to be sure the Java applet is loaded.
Try quitting the browser and launching it again.
Reference Manual for the Model MR814 Wireless Router
9-4 Troubleshooting
Make sure you are using the correct login information. The factory default login name is
admin and the password is password. Make sure that CAPS LOCK is off when entering this
information.
If the router does not save changes you have made in the Web Configuration Interface, check the
following:
When entering configuration settings, be sure to click the APPLY button before moving to
another menu or tab, or your changes are lost.
Click the Refresh or Reload button in the Web browser. The changes may have occurred, but
the Web browser may be caching the old configuration.
Troubleshooting the ISP Connection
If your router is unable to access the Internet, you should first determine whether the router is able
to obtain a WAN IP address from the ISP. Unless you have been assigned a static IP address, your
router must request an IP address from the ISP. You can determine whether the request was
successful using the Web Configuration Manager.
To check the WAN IP address:
1. Launch your browser and select an external site such as www.netgear.com
2. Access the Main Menu of the router’s configuration at http://192.168.0.1
3. Under the Maintenance heading, select Router Status
4. Check that an IP address is shown for the WAN Port
If 0.0.0.0 is shown, your router has not obtained an IP address from your ISP.
If your router is unable to obtain an IP address from the ISP, you may need to force your cable or
DSL modem to recognize your new router by performing the following procedure:
1. Turn off power to the cable or DSL modem.
2. Turn off power to your router.
3. Wait five minutes and reapply power to the cable or DSL modem.
4. When the modem’s LEDs indicate that it has reacquired sync with the ISP, reapply power to
your router.
If your router is still unable to obtain an IP address from the ISP, the problem may be one of the
following:
Reference Manual for the Model MR814 Wireless Router
Troubleshooting 9-5
Your ISP may require a login program.
Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of login.
If your ISP requires a login, you may have incorrectly set the login name and password.
Your ISP may check for your PC's host name.
Assign the PC Host Name of your ISP account as the Account Name in the Basic Settings
menu.
Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for
your PC’s MAC address. In this case:
Inform your ISP that you have bought a new network device, and ask them to use the router’s
MAC address.
OR
Configure your router to spoof your PC’s MAC address. This can be done in the Basic Settings
menu. Refer to “Configuring Manually“ on page 4-8.
If your router can obtain an IP address, but your PC is unable to load any web pages from the
Internet:
Your PC may not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www addresses)
to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS
servers for your use. If you entered a DNS address during the routers configuration, reboot
your PC and verify the DNS address as described in “Verifying TCP/IP Properties“ on page
3-5. Alternatively, you may configure your PC manually with DNS addresses, as explained in
your operating system documentation.
Your PC may not have the router configured as its TCP/IP gateway.
If your PC obtains its information from the router by DHCP, reboot the PC and verify the
gateway address as described in “Verifying TCP/IP Properties“ on page 3-5.
Troubleshooting a TCP/IP Network Using the Ping Utility
Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet
to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP
network is made very easy by using the ping utility in your PC or workstation.
Reference Manual for the Model MR814 Wireless Router
9-6 Troubleshooting
Testing the LAN Path to Your Router
You can ping the router from your PC to verify that the LAN path to your router is set up correctly.
To ping the router from a PC running Windows 95 or later:
1. From the Windows toolbar, click on the Start button and select Run.
2. In the field provided, type Ping followed by the IP address of the router, as in this example:
ping 192.168.0.1
3. Click on OK.
You should see a message like this one:
Pinging <IP address> with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
Wrong physical connections
Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN
or WAN Port LEDs Not On” on page 9-2.
Check that the corresponding Link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and router.
Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your PC or workstation.
Verify that the IP address for your router and your workstation are correct and that the
addresses are on the same subnet.
Reference Manual for the Model MR814 Wireless Router
Troubleshooting 9-7
Testing the Path from Your PC to a Remote Device
After verifying that the LAN path works correctly, test the path from your PC to a remote device.
From the Windows run menu, type:
PING -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section are displayed. If you do not
receive replies:
Check that your PC has the IP address of your router listed as the default gateway. If the IP
configuration of your PC is assigned by DHCP, this information will not be visible in your
PC’s Network Control Panel. Verify that the IP address of the router is listed as the default
gateway as described in “Verifying TCP/IP Properties“ on page 3-5.
Check to see that the network address of your PC (the portion of the IP address specified
by the netmask) is different from the network address of the remote device.
Check that your cable or DSL modem is connected and functioning.
If your ISP assigned a host name to your PC, enter that host name as the Account Name in
the Basic Settings menu.
Your ISP could be rejecting the Ethernet MAC addresses of all but one of your PCs. Many
broadband ISPs restrict access by only allowing traffic from the MAC address of your
broadband modem, but some ISPs additionally restrict access to the MAC address of a
single PC connected to that modem. If this is the case, you must configure your router to
“clone” or “spoof” the MAC address from the authorized PC. Refer to “Configuring
Manually“ on page 4-8.
Restoring the Default Configuration and Password
This section explains how to restore the factory default configuration settings, changing the
router’s administration password to password and the IP address to 192.168.0.1. You can erase the
current configuration and restore factory defaults in two ways:
Use the Erase function of the Web Configuration Manager (see Erase the Configuration“ on
page 6-5).
Use the Default Reset button on the rear panel of the router. Use this method for cases when
the administration password or IP address is not known.
Reference Manual for the Model MR814 Wireless Router
9-8 Troubleshooting
Using the Default Reset button
To restore the factory default configuration settings without knowing the administration password
or IP address, you must use the Default Reset button on the rear panel of the router.
1. Press and hold the Default Reset button until the Test LED turns on (about 10 seconds).
2. Release the Default Reset button and wait for the router to reboot.
Problems with Date and Time
The E-Mail menu in the Content Filtering section displays the current date and time of day. The
Model MR814 router uses the Network Time Protocol (NTP) to obtain the current time from one
of several Network Time Servers on the Internet. Each entry in the log is stamped with the date and
time of day. Problems with the date and time function can include:
Date shown is January 1, 2000
Cause: The router has not yet successfully reached a Network Time Server. Check that your
Internet access settings are configured correctly. If you have just completed configuring the
router, wait at least five minutes and check the date and time again.
Time is off by one hour
Cause: The router does not automatically sense Daylight Savings Time. In the E-Mail menu,
check or uncheck the box marked “Adjust for Daylight Savings Time”.
Technical Specifications A-1
Appendix A
Technical Specifications
This appendix provides technical specifications for the Model MR814 Wireless Router.
Network Protocol and Standards Compatibility
Data and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP
PPP over Ethernet (PPPoE)
Wireless Networking Specifications
Wireless Networking Standard 802.11b
Data rate 1, 2, 5.5, 11Mbps (Auto Rate Sensing)
Signal Frequency 2.4Ghz to 2.5Ghz Direct Sequence Spread Spectrum (DSSS)
Range Dep
ending on various environmental conditions,
maximums are:
Outdoor environment Indoor environment
1Mbps - 1650 ft (503 m) 1Mbps - 500 ft (152 m)
2Mbps - 1320 ft (402 m) 2Mbps - 400 ft (122 m)
5.5Mbps - 1155 ft (352 m) 5.5Mbps - 270 ft (82 m)
11Mbps - 835 ft (255 m) 11Mbps - 175 ft (53 m)
Encryption 64-bit (also called 40-bit) and 128-bit WEP data encryption
Reference Manual for the Model MR814 Wireless Router
A-2 Technical Specifications
Maximum number of wireless
hosts
Limited by the amount of wireless network traffic generated
by each node; typically 30 to 70 nodes.
Power Adapter
North America: 120V, 60 Hz, input
United Kingdom, Australia: 240V, 50 Hz, input
Europe: 230V, 50 Hz, input
Japan: 100V, 50/60 Hz, input
All regions (output): 12 V DC @ 1.2A output, 30W maximum
Physical Specifications
Dimensions: 10" x 6.7" x 1.3" (without antenna)
255 mm x 169 mm x 34 mm
Weight: 1.4 lbs.
0.62 kg
Environmental Specifications
Operating temperature: 0° to 40° C (32º to 104º F)
Operating humidity: 90% maximum relative humidity, noncondensing
Electromagnetic Emissions
Meets requirements of: FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B
Interface Specifications
LAN: 10BASE-T or 100BASE-Tx, RJ-45 (wired)
802.11b (wireless)
WAN: 10BASE-T, RJ-45
Network and Routing Basics B-1
Appendix B
Network and Routing Basics
This chapter provides an overview of IP networks, routing, and firewalls.
Basic Router Concepts
Large amounts of bandwidth can be provided easily and relatively inexpensively in a local area
network (LAN). However, providing high bandwidth between a local network and the Internet can
be very expensive. Because of this expense, Internet access is usually provided by a slower-speed
wide-area network (WAN) link such as a cable or DSL modem. In order to make the best use of the
slower WAN link, a mechanism must be in place for selecting and transmitting only the data traffic
meant for the Internet. The function of selecting and forwarding this data is performed by a router.
What is a Router?
A router is a device that forwards traffic between networks based on network layer information in
the data and on routing tables maintained by the router. In these routing tables, a router builds up a
logical picture of the overall network by gathering and exchanging information with other routers
in the network. Using this information, the router chooses the best path for forwarding network
traffic.
Reference Manual for the Model MR814 Wireless Router
B-2 Network and Routing Basics
Routers vary in performance and scale, number of routing protocols supported, and types of
physical WAN connection they support. The Model MR814 Wireless Router is a small office
router that routes the IP protocol over a single-user broadband connection.
Routing Information Protocol
One of the protocols used by a router to build and maintain a picture of the network is the Routing
Information Protocol (RIP). Using RIP, routers periodically update one another and check for
changes to add to the routing table.
The Model MR814 router supports both the older RIP-1 and the newer RIP-2 protocols. Among
other improvements, RIP-2 supports subnet and multicast protocols. RIP is not required for most
home applications.
IP Addresses and the Internet
Because TCP/IP networks are interconnected across the world, every machine on the Internet must
have a unique address to make sure that transmitted data reaches the correct destination. Blocks of
addresses are assigned to organizations by the Internet Assigned Numbers Authority (IANA).
Individual users and small organizations may obtain their addresses either from the IANA or from
an Internet service provider (ISP). You can contact IANA at www.iana.org.
The Internet Protocol (IP) uses a 32-bit address structure. The address is usually written in dot
notation (also called dotted-decimal notation), in which each group of eight bits is written in
decimal form, separated by decimal points.
For example, the following binary address:
11000011 00100010 00001100 00000111
is normally written as:
195.34.12.7
The latter version is easier to remember and easier to enter into your computer.
In addition, the 32 bits of the address are subdivided into two parts. The first part of the address
identifies the network, and the second part identifies the host node or station on the network. The
dividing point may vary depending on the address range and the application.
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-3
There are five standard classes of IP addresses. These address classes have different ways of
determining the network and host sections of the address, allowing for different numbers of hosts
on a network. Each address type begins with a unique bit pattern, which is used by the TCP/IP
software to identify the address class. After the address class has been determined, the software
can correctly identify the host section of the address. The follow figure shows the three main
address classes, including network and host sections of the address for each address type.
Figure B-1. Three Main Address Classes
The five address classes are:
•Class A
Class A addresses can have up to 16,777,214 hosts on a single network. They use an eight-bit
network number and a 24-bit node number. Class A addresses are in this range:
1.x.x.x to 126.x.x.x.
•Class B
Class B addresses can have up to 65,354 hosts on a network. A Class B address uses a 16-bit
network number and a 16-bit node number. Class B addresses are in this range:
128.1.x.x to 191.254.x.x.
•Class C
Class C addresses can have 254 hosts on a network. Class C addresses use 24 bits for the
network address and eight bits for the node. They are in this range:
192.0.1.x to 223.255.254.x.
726
1
C
lass A
N
etwork Node
C
lass B
C
lass C
Network Node
Network Node
Reference Manual for the Model MR814 Wireless Router
B-4 Network and Routing Basics
•Class D
Class D addresses are used for multicasts (messages sent to many hosts). Class D addresses are
in this range:
224.0.0.0 to 239.255.255.255.
•Class E
Class E addresses are for experimental use.
This addressing structure allows IP addresses to uniquely identify each physical network and each
node on each physical network.
For each unique value of the network portion of the address, the base address of the range (host
address of all zeros) is known as the network address and is not usually assigned to a host. Also,
the top address of the range (host address of all ones) is not assigned, but is used as the broadcast
address for simultaneously sending a packet to all hosts with the same network address.
Netmask
In each of the address classes previously described, the size of the two parts (network address and
host address) is implied by the class. This partitioning scheme can also be expressed by a netmask
associated with the IP address. A netmask is a 32-bit quantity that, when logically combined (using
an AND operator) with an IP address, yields the network address. For instance, the netmasks for
Class A, B, and C addresses are 255.0.0.0, 255.255.0.0, and 255.255.255.0, respectively.
For example, the address 192.168.170.237 is a Class C IP address whose network portion is the
upper 24 bits. When combined (using an AND operator) with the Class C netmask, as shown here,
only the network portion of the address remains:
11000000 10101000 10101010 11101101 (192.168.170.237)
combined with:
11111111 11111111 11111111 00000000 (255.255.255.0)
Equals:
11000000 10101000 10101010 00000000 (192.168.170.0)
As a shorter alternative to dotted-decimal notation, the netmask may also be expressed in terms of
the number of ones from the left. This number is appended to the IP address, following a backward
slash ( / ), as “/n.” In the example, the address could be written as 192.168.170.237/24, indicating
that the netmask is 24 ones followed by 8 zeros.
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-5
Subnet Addressing
By looking at the addressing structures, you can see that even with a Class C address, there are a
large number of hosts per network. Such a structure is an inefficient use of addresses if each end of
a routed link requires a different network number. It is unlikely that the smaller office LANs would
have that many devices. You can resolve this problem by using a technique known as subnet
addressing.
Subnet addressing allows us to split one IP network address into smaller multiple physical
networks known as subnetworks. Some of the node numbers are used as a subnet number instead.
A Class B address gives us 16 bits of node numbers translating to 64,000 nodes. Most
organizations do not use 64,000 nodes, so there are free bits that can be reassigned. Subnet
addressing makes use of those bits that are free, as shown below.
Figure B-2. Example of Subnetting a Class B Address
A Class B address can be effectively translated into multiple Class C addresses. For example, the
IP address of 172.16.0.0 is assigned, but node addresses are limited to 255 maximum, allowing
eight extra bits to use as a subnet address. The IP address of 172.16.97.235 would be interpreted as
IP network address 172.16, subnet number 97, and node number 235. In addition to extending
the number of addresses available, subnet addressing provides other benefits. Subnet addressing
allows a network manager to construct an address scheme for the network by using different
subnets for other geographical locations in the network or for other departments in the
organization.
Although the preceding example uses the entire third octet for a subnet address, note that you are
not restricted to octet boundaries in subnetting. To create more network numbers, you need only
shift some bits from the host address to the network address. For instance, to partition a Class C
network number (192.68.135.0) into two, you shift one bit from the host address to the network
address. The new netmask (or subnet mask) is 255.255.255.128. The first subnet has network
number 192.68.135.0 with hosts 192.68.135.1 to 129.68.135.126, and the second subnet has
network number 192.68.135.128 with hosts 192.68.135.129 to 192.68.135.254.
726
2
C
lass B
Network Subnet Node
Reference Manual for the Model MR814 Wireless Router
B-6 Network and Routing Basics
The following table lists the additional subnet mask bits in dotted-decimal notation. To use the
table, write down the original class netmask and replace the 0 value octets with the dotted-decimal
value of the additional subnet bits. For example, to partition your Class C network with subnet
mask 255.255.255.0 into 16 subnets (4 bits), the new subnet mask becomes 255.255.255.240.
The following table displays several common netmask values in both the dotted-decimal and the
masklength formats.
Note: The number 192.68.135.127 is not assigned because it is the broadcast address
of the first subnet. The number 192.68.135.128 is not assigned because it is the network
address of the second subnet.
Table B-1. Netmask Notation Translation Table for One Octet
Number of Bits Dotted-Decimal Value
1 128
2 192
3 224
4 240
5 248
6 252
7 254
8 255
Table B-2. Netmask Formats
Dotted-Decimal Masklength
255.0.0.0 /8
255.255.0.0 /16
255.255.255.0 /24
255.255.255.128 /25
255.255.255.192 /26
255.255.255.224 /27
255.255.255.240 /28
255.255.255.248 /29
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-7
NETGEAR strongly recommends that you configure all hosts on a LAN segment to use the same
netmask for the following reasons:
So that hosts recognize local IP broadcast packets
When a device broadcasts to its segment neighbors, it uses a destination address of the local
network address with all ones for the host address. In order for this scheme to work, all devices
on the segment must agree on which bits comprise the host address.
So that a local router or bridge recognizes which addresses are local and which are remote
Private IP Addresses
If your local network is isolated from the Internet (for example, when using NAT), you can assign
any IP addresses to the hosts without problems. However, the IANA has reserved the following
three blocks of IP addresses specifically for private networks:
10.0.0.0 - 10.255.255.255
172.16.0.0 - 172.31.255.255
192.168.0.0 - 192.168.255.255
NETGEAR recommends that you choose your private network number from this range. The
DHCP server of the Model MR814 router is preconfigured to automatically assign private
addresses.
Regardless of your particular situation, do not create an arbitrary IP address; always follow the
guidelines explained here. For more information about address assignment, refer to RFC 1597,
Address Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP
Address Space. The Internet Engineering Task Force (IETF) publishes RFCs on its Web site at
www.ietf.org.
255.255.255.252 /30
255.255.255.254 /31
255.255.255.255 /32
Table B-2. Netmask Formats
Reference Manual for the Model MR814 Wireless Router
B-8 Network and Routing Basics
Single IP Address Operation Using NAT
In the past, if multiple PCs on a LAN needed to access the Internet simultaneously, you had to
obtain a range of IP addresses from the ISP. This type of Internet account is more costly than a
single-address account typically used by a single user with a modem, rather than a router. The
Model MR814 router employs an address-sharing method called Network Address Translation
(NAT). This method allows several networked PCs to share an Internet account using only a single
IP address, which may be statically or dynamically assigned by your ISP.
The router accomplishes this address sharing by translating the internal LAN IP addresses to a
single address that is globally unique on the Internet. The internal LAN IP addresses can be either
private addresses or registered addresses. For more information about IP address translation, refer
to RFC 1631, The IP Network Address Translator (NAT).
The following figure illustrates a single IP address operation.
Figure B-3. Single IP Address Operation Using NAT
7786EA
1
92.168.0.2
1
92.168.0.3
1
92.168.0.4
1
92.168.0.5
192.168.0.1 172.21.15.105
Private IP addresses
assigned by user
Internet
IP addresses
assigned by ISP
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-9
This scheme offers the additional benefit of simple firewall-like protection because the internal
LAN addresses are not available to the Internet through the translated connection. All incoming
inquiries are filtered out by the router. This filtering can prevent intruders from probing your
system. However, using port forwarding, you can allow one PC (for example, a Web server) on
your local network to be accessible to outside users.
For more information about address assignment, refer to the IETF documents RFC 1597, Address
Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP Address Space.
For more information about IP address translation, refer to RFC 1631, The IP Network Address
Translator (NAT).
MAC Addresses and Address Resolution Protocol
An IP address alone cannot be used to deliver data from one LAN device to another. To send data
between LAN devices, you must convert the IP address of the destination device to its media
access control (MAC) address. Each device on an Ethernet network has a unique MAC address,
which is a 48-bit number assigned to each device by the manufacturer. The technique that
associates the IP address with a MAC address is known as address resolution. Internet Protocol
uses the Address Resolution Protocol (ARP) to resolve MAC addresses.
If a device sends data to another station on the network and the destination MAC address is not yet
recorded, ARP is used. An ARP request is broadcast onto the network. All stations on the network
receive and read the request. The destination IP address for the chosen station is included as part of
the message so that only the station with this IP address responds to the ARP request. All other
stations discard the request.
The station with the correct IP address responds with its own MAC address directly to the sending
device. The receiving station provides the transmitting station with the required destination MAC
address. The IP address data and MAC address data for each station are held in an ARP table. The
next time data is sent, the address can be obtained from the address information in the table.
Domain Name Server
Many of the resources on the Internet can be addressed by simple descriptive names such as
www.NETGEAR.com. This addressing is very helpful at the application level, but the descriptive
name must be translated to an IP address in order for a user to actually contact the resource. Just as
a telephone directory maps names to phone numbers, or as an ARP table maps IP addresses to
MAC addresses, a domain name system (DNS) server maps descriptive names of network
resources to IP addresses.
Reference Manual for the Model MR814 Wireless Router
B-10 Network and Routing Basics
When a PC accesses a resource by its descriptive name, it first contacts a DNS server to obtain the
IP address of the resource. The PC sends the desired message using the IP address. Many large
organizations, such as ISPs, maintain their own DNS servers and allow their customers to use the
servers to look up addresses.
IP Configuration by DHCP
When an IP-based local area network is installed, each PC must be configured with an IP address.
If the PCs need to access the Internet, they should also be configured with a gateway address and
one or more DNS server addresses. As an alternative to manual configuration, there is a method by
which each PC on the network can automatically obtain this configuration information. A device
on the network may act as a Dynamic Host Configuration Protocol (DHCP) server. The DHCP
server stores a list or pool of IP addresses, along with other information (such as gateway and DNS
addresses) that it may assign to the other devices on the network. The Model MR814 router has the
capacity to act as a DHCP server.
The Model MR814 router also functions as a DHCP client when connecting to the ISP. The router
can automatically obtain an IP address, subnet mask, DNS server addresses, and a gateway address
if the ISP provides this information by DHCP.
Wireless Networking
The Model MR814 router conforms to the Institute of Electrical and Electronics Engineers (IEEE)
802.11b standard for wireless LANs (WLANs). On an 802.11b wireless link, data is encoded using
direct-sequence spread-spectrum (DSSS) technology and is transmitted in the unlicensed radio
spectrum at 2.5GHz. The maximum data rate for the wireless link is 11 Mbps, but it will
automatically back down from 11 Mbps to 5.5, 2, and 1 Mbps when the radio signal is weak or
when interference is detected.
The 802.11b standard is also called Wireless Ethernet or Wi-Fi by the Wireless Ethernet
Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standard group promoting
interoperability among 802.11b devices.
Wireless Network Configuration
The 802.11b standard offers two methods for configuring a wireless network - ad hoc and
infrastructure.
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-11
Ad-hoc Mode (Peer-to-Peer Workgroup)
In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed
points to the network - each node can generally communicate with any other node. There is no
Access Point involved in this configuration. This mode enables you to quickly set up a small
wireless workgroup and allows workgroup members to exchange data or share printers as
supported by Microsoft Networking in the various Windows operating systems. Some vendors
also refer to ad hoc networking as Peer-to-Peer group networking.
In this configuration, network packets are directly sent and received by the intended transmitting
and receiving stations. As long as the stations are within range of one another, this is the easiest
and least expensive way to set up a wireless network.
Infrastructure Mode
With a wireless Access Point, you can operate the wireless LAN in the infrastructure mode. This
mode provides wireless connectivity to multiple wireless network devices within a fixed range or
area of coverage, interacting with wireless nodes via an antenna.
In the infrastructure mode, the wireless access point converts airwave data into wired Ethernet
data, acting as a bridge between the wired LAN and wireless clients. Connecting multiple Access
Points via a wired Ethernet backbone can further extend the wireless network coverage. As a
mobile computing device moves out of the range of one access point, it moves into the range of
another. As a result, wireless clients can freely roam from one Access Point domain to another and
still maintain seamless network connection.
Extended Service Set Identification (ESSID)
The Extended Service Set Identification (ESSID) is one of two types of Service Set Identification
(SSID). In an ad-hoc wireless network with no access points, the Basic Service Set Identification
(BSSID) is used. In an infrastructure wireless network that includes an access point, the Extended
Service Set Identification (ESSID) is used, but may still be referred to as SSID.
An SSID is a thirty-two character (maximum) alphanumeric key identifying the wireless local area
network. Some vendors refer to the SSID as network name. For the wireless devices in a network
to communicate with each other, all devices must be configured with the same SSID.
Reference Manual for the Model MR814 Wireless Router
B-12 Network and Routing Basics
Authentication and WEP Encryption
The absence of a physical connection between nodes makes the wireless links vulnerable to
eavesdropping and information theft. To provide a certain level of security, the IEEE 802.11
standard has defined two types of authentication methods, Open System and Shared Key. With
Open System authentication, a wireless PC can join any network and receive any messages that are
not encrypted. With Shared Key authentication, only those PCs that possess the correct
authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an
Open System network.
Wired Equivalent Privacy (WEP) data encryption is utilized when the wireless nodes or access
points are configured to operate in Shared Key authentication mode. There are two shared key
methods implemented in most commercially available products, 64-bit and 128-bit WEP data
encryption.
The 64-bit WEP data encryption method, allows for a five-character (40-bit) input. Additionally,
24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. (The 24
factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all
data transmitted via the wireless interface. Some vendors refer to the 64-bit WEP data encryption
as 40-bit WEP data encryption since the user-configurable portion of the encryption key is 40 bits
wide.
The 128-bit WEP data encryption method consists of 104 user-configurable bits. Similar to the
forty-bit WEP data encryption method, the remaining 24 bits are factory set and not user
configurable. Some vendors allow passphrases to be entered instead of the cryptic hexadecimal
characters to ease encryption key entry.
Wireless Channel Selection
IEEE 802.11 wireless nodes communicate with each other using radio frequency signals in the
ISM (Industrial, Scientific, and Medical) band between 2.4Ghz and 2.5Ghz. Neighboring
channels are 5Mhz apart. However, due to spread spectrum effect of the signals, a node sending
signals using a particular channel will utilize frequency spectrum12.5Mhz above and below the
center channel frequency. As a result, two separate wireless networks using neighboring channels
(for example, channel 1 and channel 2) in the same general vicinity will interfere with each other.
Applying two channels that allow the maximum channel separation will decrease the amount of
channel cross-talk, and provide a noticeable performance increase over networks with minimal
channel separation.
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-13
The radio frequency channels used are listed in Table B-3:
Note: The available channels supported by the wireless products in various countries are different.
The preferred channel separation between the channels in neighboring wireless networks is 25
MHz (5 channels). This means that you can apply up to three different channels within your
wireless network. There are only 11 usable wireless channels in the United States. It is
recommended that you start using channel 1 and grow to use channel 6, and 11 when necessary, as
these three channels do not overlap.
Table B-3. 802.11 Radio Frequency Channels
Channel Center Frequency Frequency Spread
1 2412Mhz 2399.5Mhz - 2424.5Mhz
2 2417Mhz 2404.5Mhz - 2429.5Mhz
3 2422Mhz 2409.5Mhz - 2434.5Mhz
4 2427Mhz 2414.5Mhz - 2439.5Mhz
5 2432Mhz 2419.5Mhz - 2444.5Mhz
6 2437Mhz 2424.5Mhz - 2449.5Mhz
7 2442Mhz 2429.5Mhz - 2454.5Mhz
8 2447Mhz 2434.5Mhz - 2459.5Mhz
9 2452Mhz 2439.5Mhz - 2464.5Mhz
10 2457Mhz 2444.5Mhz - 2469.5Mhz
11 2462Mhz 2449.5Mhz - 2474.5Mhz
12 2467Mhz 2454.5Mhz - 2479.5Mhz
13 2472Mhz 2459.5Mhz - 2484.5Mhz
Reference Manual for the Model MR814 Wireless Router
B-14 Network and Routing Basics
Ethernet Cabling
Although Ethernet networks originally used thick or thin coaxial cable, most installations currently
use unshielded twisted pair (UTP) cabling. The UTP cable contains eight conductors, arranged in
four twisted pairs, and terminated with an RJ45 type connector. A normal "straight-through" UTP
Ethernet cable follows the EIA568B standard wiring and pinout as described in Table B-4.
Uplink Switches, Crossover Cables, and MDI/MDIX Switching
In the wiring table above, the concept of transmit and receive are from the perspective of the PC,
which is wired as Media Dependant Interface (MDI). In this wiring, the PC transmits on pins 1 and
2. At the hub, the perspective is reversed, and the hub receives on pins 1 and 2. This wiring is
referred to as Media Dependant Interface - Crossover (MDI-X). When connecting a PC to a PC, or
a hub port to another hub port, the transmit pair must be exchanged with the receive pair. This
exchange is done by one of two mechanisms:
Uplink switch
Most hubs provide an Uplink switch which will exchange the pairs on one port, allowing that
port to be connected to another hub using a normal Ethernet cable.
Table B-4. UTP Ethernet cable wiring, straight-through
Pin Wire color Signal
1 Orange/White Transmit (Tx) +
2 Orange Transmit (Tx) -
3 Green/White Receive (Rx) +
4Blue
5 Blue/White
6 Green Receive (Rx) -
7 Brown/White
8Brown
Reference Manual for the Model MR814 Wireless Router
Network and Routing Basics B-15
Crossover cable
A crossover cable is a special cable in which the transmit and receive pairs are exchanged at
one of the two cable connectors. Crossover cables are often unmarked as such, and must be
identified by comparing the two connectors. Since the cable connectors are clear plastic, it is
easy to place them side by side and view the order of the wire colors on each. On a
straight-through cable, the color order will be the same on both connectors. On a crossover
cable, the orange and blue pairs will be exchanged from one connector to the other.
Cable Quality
A twisted pair Ethernet network operating at 10 Mbits/second (10BASE-T) will often tolerate low
quality cables, but at 100 Mbits/second (10BASE-Tx) the cable must be rated as Category 5, or
"Cat 5" or "Cat V", by the Electronic Industry Association (EIA). This rating will be printed on the
cable jacket. A Category 5 cable will meet specified requirements regarding loss and crosstalk. In
addition, there are restrictions on maximum cable length for both 10 and 100 Mbits/second
networks.
Reference Manual for the Model MR814 Wireless Router
B-16 Network and Routing Basics
Glossary
1
Glossary
10BASE-T
IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.
100BASE-Tx
IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.
802.11b
IEEE specification for wireless networking at 11 Mbps using direct-sequence
spread-spectrum (DSSS) technology and operating in the unlicensed radio
spectrum at 2.5GHz.
Denial of Service
attack
DoS. A hacker attack designed to prevent your computer or network from
operating or communicating.
DHCP
See Dynamic Host Configuration Protocol.
DNS
See Domain Name Server.
domain name
A descriptive name for an address or group of addresses on the Internet.
Domain names are of the form of a registered entity name plus one of a
number of predefined top level suffixes such as .com, .edu, .uk, etc. For
example, in the address mail.NETGEAR.com, mail is a server name and
NETGEAR.com is the domain.
Domain Name Server
A Domain Name Server (DNS) resolves descriptive names of network
resources (such as www.NETGEAR.com) to numeric IP addresses.
Dynamic Host
Configuration
Protocol
DHCP. An Ethernet protocol specifying how a centralized DHCP server can
assign network configuration information to multiple DHCP clients. The
assigned information includes IP addresses, DNS addresses, and gateway
(router) addresses.
ESSID
The Extended Service Set Identification (ESS ID) is a thirty-two character
(maximum) alphanumeric key identifying the wireless local area network.
Gateway
A local device, usually a router, that connects hosts on a local network to other
networks.
Reference Manual for the Model MR814 Wireless Router
2 Glossary
IP
See Internet Protocol.
IP Address
A four-byte number uniquely defining each host on the Internet. Ranges of
addresses are assigned by Internic, an organization formed for this purpose.
Usually written in dotted-decimal notation with periods separating the bytes
(for example, 134.177.244.57).
IPSec
Internet Protocol Security. IPSec is a series of guidelines for securing private
information transmitted over public networks. IPSec is a VPN method
providing a higher level of security than PPTP.
ISP
Internet service provider.
Internet Protocol
The main internetworking protocol used in the Internet. Used in conjunction
with the Transfer Control Protocol (TCP) to form TCP/IP.
LAN
See local area network.
local area network
LAN. A communications network serving users within a limited area, such as
one floor of a building. A LAN typically connects multiple personal
computers and shared network devices such as storage and printers. Although
many technologies exist to implement a LAN, Ethernet is the most common
for connecting personal computers.
MAC address
Media Access Control address. A unique 48-bit hardware address assigned to
every Ethernet node. Usually written in the form 01:23:45:67:89:ab.
Mbps
Megabits per second.
MSB
See Most Significant Bit or Most Significant Byte.
MRU
See Maximum Receive Unit.
Maximum Receive
Unit
The size in bytes of the largest packet that can be sent or received.
Most Significant Bit or
Most Significant Byte
The portion of a number, address, or field that is farthest left when written as a
single number in conventional hexadecimal ordinary notation. The part of the
number having the most value.
NAT
See Network Address Translation.
netmask
A number that explains which part of an IP address comprises the network
address and which part is the host address on that network. It can be
expressed in dotted-decimal notation or as a number appended to the IP
address. For example, a 28-bit mask starting from the MSB can be shown as
255.255.255.192 or as /28 appended to the IP address.
Reference Manual for the Model MR814 Wireless Router
Glossary
3
Network Address
Translation
A technique by which several hosts share a single IP address for access to the
Internet.
packet
A block of information sent over a network. A packet typically contains a
source and destination network address, some protocol and length
information, a block of data, and a checksum.
PPP
See Point-to-Point Protocol.
PPP over Ethernet
PPPoE. PPP over Ethernet is a protocol for connecting remote hosts to the
Internet over an always-on connection by simulating a dial-up connection.
PPTP
Point-to-Point Tunneling Protocol. A method for establishing a virtual private
network (VPN) by embedding Microsoft’s network protocol into Internet
packets.
PSTN
Public Switched Telephone Network.
Point-to-Point
Protocol
PPP. A protocol allowing a computer using TCP/IP to connect directly to the
Internet.
RFC
Request For Comment. Refers to documents published by the Internet
Engineering Task Force (IETF) proposing standard protocols and procedures
for the Internet. RFCs can be found at www.ietf.org.
RIP
See Routing Information Protocol.
router
A device that forwards data between networks. An IP router forwards data
based on IP source and destination addresses.
Routing Information
Protocol
A protocol in which routers periodically exchange information with one
another so that they can determine minimum distance paths between sources
and destinations.
SSID
Service Set Identification. A thirty-two character (maximum) alphanumeric
key identifying the wireless local area network. For the wireless devices in a
network to communicate with each other, all devices must be configured with
the same SSID.
subnet mask
See netmask.
UTP
Unshielded twisted pair. The cable used by 10BASE-T and 100BASE-Tx
Ethernet networks.
VPN
Virtual Private Network. A method for securely transporting data between two
private networks by using a public network such as the Internet as a
connection.
Reference Manual for the Model MR814 Wireless Router
4 Glossary
WAN
See wide area network.
WEP
Wired Equivalent Privacy. WEP is a data encryption protocol for 802.11b
wireless networks. All wireless nodes and access points on the network are
configured with a 64-bit or 128-bit Shared Key for data encryption.
wide area network
WAN. A long distance link used to extend or connect remotely located local
area networks. The Internet is a large WAN.
Wi-Fi
See 802.11b. A trade name for the 802.11b wireless networking standard,
given by the Wireless Ethernet Compatibility Alliance (WECA, see http://
www.wi-fi.net), an industry standard group promoting interoperability among
802.11b devices.
Windows Internet
Naming Service
WINS. Windows Internet Naming Service is a server process for resolving
Windows-based computer names to IP addresses. If a remote network
contains a WINS server, your Windows PCs can gather information from that
WINS server about its local hosts. This allows your PCs to browse that remote
network using Network Neighborhood.
WINS
See Windows Internet Naming Service.
Index 1
Numerics
802.11b B-10
A
Account Name 4-5, 4-7, 4-8
Address Resolution Protocol B-9
ad-hoc mode B-11
antenna orientation 2-4
B
backup configuration 7-6
BSSID B-11
C
cables, pinout B-14
Cabling B-14
Cat5 cable 2-2, 2-5, B-15
Channel 5-3, B-12
configuration
automatic by DHCP 1-4
backup 7-6
erasing 7-6
restore 7-5
router, initial 4-1
content filtering 1-2, 6-1
conventions
typography xvi
crossover cable 2-6, 9-3, B-15
customer support iii
D
date and time 9-8
Daylight Savings Time 9-8
daylight savings time 6-9
default reset button 9-8
DHCP 1-4, B-10
DHCP Client ID 3-7
DHCP Setup field, Ethernet Setup menu 7-2
DMZ 1-3, 8-2, 8-5
DNS Proxy 1-4
DNS server 3-11, 4-5, 4-6, 4-8, 4-9
DNS, dynamic 8-6
domain 3-11
Domain Name 4-5, 4-7, 4-8
domain name server (DNS) B-9
Dynamic DNS 8-6
E
End Port 8-3
EnterNet 3-9
erase configuration 7-6
ESSID B-11
Ethernet cable B-14
F
factory settings, restoring 7-6
features 1-1
Flash memory, for firmware upgrade 1-5
front panel 2-3
G
gateway address 3-10, 3-11
Index
2 Index
H
Half Life 8-4
host name 4-5, 4-7, 4-8
I
IANA
contacting B-2
IETF xv
Web site address B-7
infrastructure mode B-11
installation 1-5
Internet account
address information 3-9
establishing 3-9
IP addresses 3-10, 3-11
and NAT B-8
and the Internet B-2
assigning B-2, B-9
auto-generated 9-3
private B-7
translating B-9
IP configuration by DHCP B-10
IP networking
for Macintosh 3-6
for Windows 3-2, 3-5
K
KALI 8-4
L
LAN IP Setup Menu 8-7
LEDs
description 2-3
troubleshooting 9-2
log
sending 6-8
log entries 6-2
M
MAC address 9-7, B-9
spoofing 4-6, 4-9, 9-5
MAC address filter 5-4
Macintosh 3-10
DHCP Client ID 3-7
Obtaining ISP Configuration Information 3-11
MDI/MDI-X wiring B-14
metric 8-11
N
NAT. See Network Address Translation
NETGEAR
contacting xv
netmask
translation table B-6
Network Address Translation 1-4, B-8
Network Time Protocol 6-9, 9-8
NTP 6-9, 9-8
O
Open System authentication B-12
P
package contents 2-1
Passphrase 5-5
passphrase 1-2
password
restoring 9-7
PC, using to configure 3-12
ping 8-6
pinout, Ethernet cable B-14
placement 5-2
port filtering 6-4
Port Forwarding 8-2
port forwarding behind NAT B-9
Port Forwarding Menu 8-2
port numbers 6-5
PPP over Ethernet 1-4, 3-9
PPPoE 1-4, 3-9, 4-7
Index 3
Primary DNS Server 4-5, 4-6, 4-8, 4-9
protocols
Address Resolution B-9
DHCP 1-4, B-10
Routing Information 1-4, B-2
support 1-1
publications, related xv
Q
Quake 8-4
R
range 5-2
range, port forwarding 8-3
rear panel 2-4
Region 5-3
remote management 8-12
requirements
access device 2-2
hardware 2-2
reserved IP adresses 8-9
reset button, clearing config 9-8
restore configuration 7-5
restore factory settings 7-6
RFC
1466 B-7, B-9
1597 B-7, B-9
1631 B-8, B-9
finding B-7
RIP (Router Information Protocol) 8-8
router concepts B-1
Routing Information Protocol 1-4, B-2
S
Secondary DNS Server 4-5, 4-6, 4-8, 4-9
security 1-1, 1-2
service numbers 6-6
Setup Wizard 4-1
Shared Key authentication 1-3, B-12
SMTP 6-8
spoof MAC address 9-5
SSID 2-5, 5-1, 5-3, B-11
Start Port 8-3
Static Routes 8-10
subnet addressing B-5
subnet mask 3-10, 3-11, B-5
T
TCP/IP
configuring 3-1
network, troubleshooting 9-5
TCP/IP properties
verifying for Macintosh 3-8
verifying for Windows 3-5, 3-6
technical support xv
time of day 9-8
time zone 6-9
time-stamping 6-9
troubleshooting 9-1
Trusted Host 6-4
typographical conventions xvi
U
Uplink port 2-5
uplink switch B-14
USB 3-9
W
WEP 5-4, B-12
WEP encryption 1-2
WEP, Keys 5-5
Wi-Fi B-10
Windows, configuring for IP routing 3-2, 3-5
winipcfg utility 3-5
WinPOET 3-9
Wired Equivalent Privacy. See WEP
Wireless Ethernet B-10
4 Index
World Wide Web iii
106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Netgear MR814 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info