Bedienungsanleitung Netgear WGAP150 (Seite 26 von 134) (Englisch)

519682

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

26 |

WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point

3. Specify the 802.11n profile fields as explained Table 2-5.

Table 2-5. 802.11b/g Profile Settings

Field Descriptions

Radio Enable The radio is enabled by default. To turn off the radio, deselect the Radio Enable

checkbox. Doing so disables access through the wireless access point, which can

be helpful for configuration, network tuning, or troubleshooting activities.

Radio Policy Select one of the following modes from the pull-down menu:

• 802.11b/g. The wireless access point accepts both 802.11b and 802.11g client

association requests. This mode is also referred to as Mixed Mode.

• 802.11b Only. The wireless access point accepts 802.11b client association

requests only.

• 802.11g Only. The wireless access point accepts 802.11g client association

requests only.

Country This pull-down menu lets you specify your country/region.

RF Channel This pull-down menu lets you to specify the 802.11 channel. The available options

for 802.11b or 802.11g are from 1 to 11 for the U.S. (which is the default setting) and

from 1 to 13 for Europe. For automatic channel selection, select Auto. For more

information about operating frequencies, see the guidelines about channels below

this table.

Tx Output Power This pull-down menu lets you to specify the transmission power. The available

options are from 27 dBm to 18 dBm. By default, the Tx Output Power is 27 dBm.

Note: Make sure that you comply with the regulatory requirements for total radio

frequency (RF) output power in your country.

You should not need to change the operating frequency (channel) unless you notice

interference problems, or are setting up the wireless access point near another wireless

access point. Observe the following guidelines:

• Wireless access points use a fixed channel. You can select a channel that provides

the least interference and best performance. In the USA and Canada, 11 channels

are available.

• If using multiple wireless access points, it is better if adjacent wireless access points

use different channels to reduce interference. The recommended channel spacing

between adjacent wireless access points is five channels (for example, use channels

1 and 6, or 6 and 11).

• In “infrastructure” mode, wireless stations normally scan all channels, looking for a

wireless access point. If more than one wireless access point can be used, the one

with the strongest signal is used. This can happen only when the wireless access

points use the same SSID. The WGAP150 wireless access point functions in

“infrastructure” mode by default.

For more information about wireless channels, see the online document that you can

access from “Wireless Networking Basics” in Appendix B.

4. Click Save or Save to Flash & Activate to save your settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WGAP150 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear WGAP150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info