Bedienungsanleitung Netgear WNDR4720 (Seite 109 von 146) (Englisch)

519535

109

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

Advanced Settings

109

CENTRIA WNDR4700/WNDR4720

router, you can tell the router to open additional incoming ports when a particular outgoing

port originates a session.

An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at

destination port 6667. The IRC server not only responds to your originating source port, but

also sends an “identify” message to your computer on port 113. Using port triggering, you can

tell the router, “When you initiate a session with destination port 6667, you have to also allow

incoming traffic on port 113 to reach the originating computer.” Using steps similar to the

preceding example, the following sequence shows the effects of the port triggering rule you

have defined:

1. You open an IRC client program to start a chat session on your computer.

2. Your IRC client composes a request message to an IRC server using a destination port

number of 6667, the standard port number for an IRC server process. Your computer

then sends this request message to your router.

3. Your router creates an entry in its internal session table describing this communication

session between your computer and the IRC server. Your router stores the original

information, performs Network Address Translation (NAT) on the source address and

port, and sends this request message through the Internet to the IRC server.

4. Noting your port triggering rule and having observed the destination port number of

6667, your router creates an additional session entry to send any incoming port 113

traffic to your computer.

5. The IRC server sends a return message to your router using the NAT-assigned source

port (as in the previous example, say port 33333) as the destination port. The IRC

server also sends an “identify” message to your router with destination port 113.

6. Upon receiving the incoming message to destination port 33333, your router checks its

session table to determine whether there is an active session for port number 33333.

Finding an active session, the router restores the original address information replaced

by NAT and sends this reply message to your computer.

7. Upon receiving the incoming message to destination port 113, your router checks its

session table and learns that there is an active session for port 113, associated with

your computer. The router replaces the message’s destination IP address with your

computer’s IP address and forwards the message to your computer.

8. When you finish your chat session, your router eventually senses a period of inactivity in

the communications. The router then removes the session information from its session

table, and incoming traffic is no longer accepted on port numbers 33333 or 113.

To configure port triggering, you need to know which inbound ports the application needs.

Also, you need to know the number of the outbound port that will trigger the opening of the

inbound ports. Usually, you can determine this information by contacting the publisher of the

application or the relevant user groups or news groups.

Note: Only one computer at a time can use the triggered application.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WNDR4720 Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear WNDR4720

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info