Bedienungsanleitung Netgear WPN802 (Seite 2 von 2) (Englisch)

519643

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

May 2005

Troubleshooting Tips

Here are some tips for correcting simple problems you may have.

No lights are lit on the access point.

The access point has no power.

• Make sure the power cord is connected to the access point and plugged in to a

working power outlet or power strip.

• Make sure you are using the correct NETGEAR power adapter supplied with your

access point.

The Ethernet light is not lit.

There is a hardware connection problem.

• Make sure the cable connectors are securely plugged in at the access point and the

network device (hub, switch, or router).

• Make sure the connected device is turned on.

The WLAN light is not lit.

The access point’s antennas are not working.

• If the Wireless LAN activity light stays off, disconnect the adapter from its power

source and then plug it in again.

• Contact NETGEAR if the WLAN light remains off.

I cannot configure the access point from a browser.

Check these items:

• The WPN802 is properly installed, LAN connections are OK, and it is powered on.

Check that the LAN port LED is green to verify that the Ethernet connection is OK.

• If you are using the NetBIOS name of the WPN802 to connect, ensure that your PC

and the WPN802 are on the same network segment or that there is a WINS server on

your network.

• If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the

range of the WPN802. The WPN802 default IP Address is 192.168.0.231 and the

default Subnet Mask is 255.255.255.0. The WPN802 default setting is for a static IP

address. If the network where you are connecting it is using DHCP, configure it

accordingly. See the Reference Manual on the Resource CD for the Wireless Access

Point for more details.

I cannot access the Internet or the LAN with a wireless capable

computer.

There is a configuration problem. Check these items:

• You may not have restarted the computer with the wireless adapter to have TCP/IP

changes take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct TCP/IP settings to

communicate with the network. Restart the computer and check that TCP/IP is set up

properly for that network. The usual setting for Windows on the Network Properties

is set to “Obtain an IP address automatically.”

• The access point’s default values may not work with your network. Check the access

point default configuration against the configuration of other devices in your network.

• For full instructions on changing the access point’s default values, see the Reference

Manual on the Resource CD for the Wireless Access Point.

Technical Support

Thank you for selecting NETGEAR products.

To register your product, go to: http://www.NETGEAR.com/register

Go to http://www.NETGEAR.com/support for support information.

NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand

and product names are trademarks or registered trademarks of their respective holders. Information is subject to

change without notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WPN802 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear WPN802

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info