Bedienungsanleitung Netgear WPN824 (Seite 162 von 174) (Englisch)

519642

162

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

Reference Manual for the RangeMax Wireless Router WPN824

4 Glossary

202-10072-01, March 2005

for cables or wires. Bluetooth is a frequency-hopping technology in the 2.4 GHz frequency spectrum, with a

range of 30 feet and up to 11Mbps raw data throughput.

Bridge

A product that connects a local area network (LAN) to another local area network that uses the same

protocol (for example, wireless, Ethernet or token ring). Wireless bridges are commonly used to link

buildings in campuses.

Client or Client devices

Any computer connected to a network that requests services (files, print capability) from another member of

the network. Clients are end users. Wi-Fi client devices include PC Cards that slide into laptop computers,

mini-PCI modules embedded in laptop computers and mobile computing devices, as well as USB and PCI/

ISA bus Wi-Fi radios. Client devices usually communicate with hub devices like access points and

gateways.

Collision avoidance

A network node characteristic for proactively detecting that it can transmit a signal without risking a

collision, thereby ensuring a more reliable connection.

Crossover cable

A special cable used for networking two computers without the use of a hub. Crossover cables may also be

required for connecting a cable or DSL modem to a wireless gateway or access point. Instead of the signals

transferring in parallel paths from one set of plugs to another, the signals "crossover." If an eight-wire cable

was being used, for instance, the signal would start on pin one at one end of the cable and end up on pin

eight at the other end. They "cross-over" from one side to the other.

CSMA/CA (Carrier Sense Multiple Action/Collision Avoidance)

CSMA/CA is the principle medium access method employed by IEEE 802.11 WLANs. It is a "listen before

talk": method of minimizing (but not eliminating) collisions caused by simultaneous transmission by

multiple radios. IEEE 802.11 states collision avoidance method rather than collision detection must be used,

because the standard employs half duplex radios—radios capable of transmission or reception—but not both

simultaneously.

Unlike conventional wired Ethernet nodes, a WLAN station cannot detect a collision while transmitting. If a

collision occurs, the transmitting station will not receive an ACKnowledge packet from the intended receive

station. For this reason, ACK packets have a higher priority than all other network traffic. After completion

of a data transmission, the receive station will begin transmission of the ACK packet before any other node

can begin transmitting a new data packet. All other stations must wait a longer pseudo randomized period of

time before transmitting. If an ACK packet is not received, the transmitting station will wait for a subsequent

opportunity to retry transmission

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WPN824 Seite 162

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear WPN824

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info