763932
2
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
Installation and user’s manual. Read carefully and keep it for later reference
For ASPEN / MALIBU / MONTANA / ROVER / SILVER spa
Deze handleiding is ook te gebruiken voor de NetSpa Canyon
For your own safety and that of your product, make sure to following the safety precautions below.
Fail to follow the instruction may result in serious injury, property damage or death. Improper ins-
tallation or operation will void the warranty.
Read, understand and follow all instructions:
DANGER
Risk of accidental drowning:
- Extreme caution must be exercised to prevent unauthorized access by children.
- Inspect the spa cover regularly for leak, premature wear and tear, damage or signs of deterioration.
Never use a worn or damaged cover: it will not provide the level of protection required to prevent unsuper-
vised access to the spa by a child.
- Always lock the spa cover after each use.
Risk of injury:
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly quali-
ed persons in order to avoid a hazard.
Risk of Electric Shock:
- Do not permit any electrical appliances, such as a light, telephone, radio or television within 1.5m (5 feet)
of a spa tub.
- Do not use the spa when it is raining, thundering or lightning..
WARNING
To reduce the risk of electric shock, do not use an extension cord, timers, plug adapters or converter
plugs to connect the unit to electric supply; provide a properly located outlet.
The spa electrical appliance should be supplied through a residual current device (RCD) having a rated
residual operating current not exceeding 10mA.
Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must
be inaccessible to occupants in the spa.
Parts incorporating electrical components, except remote control devices, must be located or xed so
that they cannot fall into the spa.
Residential electrical connection box must be located safely with a distance of at least 2m away from the
spa.
Electric installation should fulll the local requirement or standards.
This appliance can be used by children aged from 8 years and above and persons with reduced physi-
cal, sensory or mental capabilities or lack of experience and knowledge if they have been given supervi-
sion or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
To reduce the risk or injury, do not permit children use this product unless they are closely supervised all
times.
To reduce the risk of child drowning, supervise children all times. Attach and lock spa cover after each
use.
Make sure the oor is capable of supporting the expected load (≥ 500kg/m²).
Adequate draining system must be provided around the spa to deal with overow water.
To avoid damage, do not left the appliance empty for an extended period.
To avoid damage to the pump, the spa must never be operated unless the spa is lled with water.
Immediately leave spa if uncomfortable or sleepy.
To reduce the risk of injury :
- Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.
IMPORTANT SAFETY INSTRUCTIONS
EN
In order to avoid the possibility of hyperthermia (heat stress) occurring it is recommended that the average
temperature of spa-pool water should not exceed 40°C (104°F).
- Since excessive water temperatures have a high potential for causing fetal damage during the early
months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 38°C
(100°F).
- Before entering a spa or hot tub the user should measure the water temperature with an accurate ther-
mometer since the tolerance of water temperature regulating devices varies.
- The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness with the
possibility or drowning.
- The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in spas.
The causes and symptoms of hyperthermia may be described as follows:
Hyperthermia occurs when the internal temperature of body reaches a level several degrees above
the normal body temperature 37°C (98.6°F). The symptoms of hyperthermia include an increase in the
internal temperature of body, dizziness, lethargy, drowsiness, and fainting. The e󰀨ect of hyperemia include
failure to perceive heat; failure to recognize the need to exit spa; unawareness of impending hazard; fetal
damage in pregnant women; physical inability to exit the spa; and unconsciousness resulting in the danger
of drowning.
- Obese persons or persons with a history of heart disease, low or high blood pressure, circulatory system
problem, or diabetes should consult a physician before using a spa.
- Persons using medication should consult a physician before using a spa since some medication may
induce drowsiness while other medication may a󰀨ect heart rate, blood pressure, and circulation.
- Check with doctor before use if pregnant, diabetic, in poor health, or under medical care.
People with infectious disease should not use a spa or hot tub.
To avoid injury exercise care when entering or existing the spa or hot tub.
Water temperature in excess of 42°C (108°F) may be injurious to your health.
Never use a spa or hot tub alone or allow others to use the spa alone.
Do not use a spa or hot tub immediately following strenuous exercise.
The spa should not be setup or left out in temperature lower than 10°C (50°F).
Do not put the spa under 0°C (32°F) environment in order to avoid freezing if there is still water in the
pool.
Do not turn on the spa when the water is frozen.
Never pour water with a temperature higher than 40°C(104°F) into the spa directly.
Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any
adjustment to the product.
Never jump or dive into a spa or any shallow body of water.
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge
trimmers and other equipment.
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
Do not use the spa if damaged in delivery and/or malfunctioning in any way.
Keep all pets away from the spa to avoid any damage.
Do not add bath oil or bath salt to the spa water.
Do not leave an empty pool outside.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a timer, or connected to a circuit that is regularly
switched on and o󰀨 by the utility.
ASPEN
4 persons
MONTANA / MALIBU
4 persons
MONTANA / MALIBU
6 persons
ROVER / MALIBU
5/6 persons
Model SP-ASP130B SP-MTA135B
SP-MBU135B
SP-MTA165B
SP-MBU165B
SP-ROV155
SP-SLV155
Capacity 4 persons 4 persons 6 persons 5/6 persons
Dimension (outer) 66.1″ × 66.1″ × 27.6″
168 × 168 × 70 cm
Ø 68.9″ × 27.6″
Ø 175 × 70 cm
Ø 80.3″ × 27.6″
Ø 204 × 70 cm
76.8″ × 76.8″ × 27.6″
195 × 195 × 70 cm
Dimensions (inner) 50.3″ × 50.3″ × 27.5″
128 × 128 × 70 cm
Ø 51.8″ × 27.5″
Ø 130 × 70 cm
Ø 62.9″ × 27,5″
Ø 160 × 70 cm
61.0″ × 61.0″ × 27.5″
155 × 155 × 70 cm
Water capacity 700 L 700 L 930 L 850 L
Power supply 220-240 V 50 Hz 220-240 V 50 Hz 220-240 V 50 Hz 220-240 V 50 Hz
Heater 1500 W 1500 W 1500 W 1500 W
Air blower 650 W 650 W 650 W 650 W
Filter 40 W (2006 L/h) 40 W (2006 L/h) 40 W (2006 L/h) 40 W (2006 L/h)
Max heat temperature 42°C 42°C 42°C 42°C
Material PVC PVC PVC PVC
Net weight 25.6 kg 25.6 kg 27.8 kg 26.7kg
Gross weight 30.2 kg 30.2 kg 33.2 kg 31.4kg
Package dimension 24.8″ x 22″ x 22″
63 x 56.5 x 56.5 cm
24.8″ x 22″ x 22″
63 x 56.5 x 56.5 cm
27″ x 24.8″ x 22″
68.5 x 63 x 56.5 cm
24.8″ x 22″ x 22″
63 x 56.5 x 56.5 cm
Test certicate CE CE CE CE
Heating e󰀩ciency
Ambient temperature : 20°C 1.5 - 2.5°C/h 1.5 - 2.5°C/h 1.5 - 2.5°C/h 1.5 - 2.5°C/h
1. SPECIFICATIONS
1.1. Specications
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). This symbol indicates
that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical
and electronic equipment. Disposal of the appliance shall be carried out in accordance with the local environment regulations for waste disposal.
The CE mark indicates that the product complies with European directives in relation to 2006/95/CE (low voltage), 2004/108/CE (Compliance with the
Electromagnetic Compatibility), 2011/65/UE (restriction of the use of certain hazardous substances in electrical and electronic equipment), 2009/125/CE
(Ecodesign directive).
EN
Ensure to check all parts are present:
2. PACKAGE LIST
2.1. Package list
Top cover Inflatable structure Base protector Pump unit
RCD plug Airflow valve Drainage cap Inflating hose
Pump unit connectors Drain hose Filter cartridges Filtration support
Caps Repair kit Installation DVD
3.2. RCD test
1. Insert the plug into the
power outlet.
2. Press the «RESET» button,
the indicator light turns red.
3. Press the «TEST» button,
the indicator light turns o󰀨.
4. Press the «RESET» button,
the indicator light turns red.
The RCD works properly.
3.1. Site selection
Clean the place A level placeA place with an awning
WARNING : Before proceed to installation your spa, please make sure that the future
location meets the following conditions :
A level place
Wide enough to support the pool and its pump unit.
Able to support more than 500 kg/m².
Sheltered from the sun and bad weather.
Clean and free from sharp objects.
3. INSTALLATION
WARNING: The RCD plug must be tested before each use..
Do not use if RCD test fails and see chapter 6.1.
The installation and maintenance instructions described in the
following pages are also detailed on the DVD included.
Our installation and maintenance videos are also available on
our website www.netspa.eu.
EN
3.3. Assembling
1) Install the base protector to where
you want to install your spa and pull
out the straps.
2) Unfold the inatable spa over the
base protector.
3) Bring the pump unit to the inatable
spa.
4) Connect the ination hose to the
pump on the socket .
7) Inate the inatable spa for about
10 minutes. Ensure that the spa is
rmly inated.
10) Put the sock on the lter cartridge
then screw it onto the lower suction
inside the basin.
8) Remove the ination hose and
screw the cap rmly in place.
11) Ensure that the drain caps are
properly closed before before lling
the spa
9) Connect the unit pump to the pool
using the 3 connectors to screw.
Ensure the icons on the pump and the
pool match up
12) Fill the spa pool until the indicated
ll level is reached.
Your spa is ready to be used.
5) Insert the ination hose into the
inatable spa
6) Connect the pump unit then press
the button to inate the spa.
The air ow valve prevents your spa
from over-inating.
EN
Press the lter button to activate the water ltration. The green indicator light will
turn on when the ltration system is activated.
Note:
- If massage function is on, the ltration can’t be activated.
Press the heating button to activate water heating and ltering system at the
same time. The green indicator light of lter and red indicator light of heating will
turn on at same time
The pump does not stop heating until the current water temperature reaches the
set temperature; and the heating system will restart after the current water tem-
perature drops 2°C below the set temperature automatically.
Maximum heating temperature: 42°C (107°F)
Important :
When the ltering system has worked 150 hours accumulatively, buzzing
will warn to remind you to clean the lter, at the same time, the light of the
ltering function will ash. You can hold the ltering button 5 seconds to
turn o the buzzing. The ltering system will turn o, you can press the
button to active the ltering system again.
Note :
- The heating system is dependent on the ltration system and it can operate without.
- After turning off the heating system, the ltration system will still work.
- If the massage function is active, the ltration and heating functions can be activated.
4.3. Pool cover and security
After each use, the control panel must be locked and the pool must be coated with its
top cover and it must be attached to the base protector with the safety buckles.
Each safety buckles has a lock system ; closed buckle, the latch in up position locks
the buckle, the latch in down position unlocks the buckle.
The top cover keeps the heat from the water and secures the pool.
5.1. Water maintenance
WARNING : A bad pool water quality can harm your health.
Depending on the frequency and conditions of use:
- The lter cartridge should be regularly cleaned (150 hours max.).
- The lter cartridge should be replaced every 1 to 2 month.
- The pool water should be changed every 15 to 30 days.
Use a water test kit to control the parameters of the water before using the spa, or at
least once a week.
Use disinfection products for the spa. The treatment products should be used with
caution and it is imperative to refer to their instructions.
Damage resulting from improper use of treatment products is not covered by warranty
(overdose, shock treatment, ...).
1. Water balance
The water balance (pH) must be maintain between 7 and 7.4.
2. Water Sanitation
To sanitize the pool water, we suggest using an active oxygen-based
treatment or bromine placed in a oating dispenser. (Dispenser sold
separately).
5. MAINTENANCE
5.2. Cleaning and replacing lter cartridge
Dirty lter cartridge may contaminate the pool water and cause damage to the heating
function.
1. Unscrew the lter case by turning it counter-clockwise. Take out the lter cartridge
from the case.
2. Rinse o󰀨 the lter cartridge with a garden hose. If the lter cartridge remains dirty
and discoloured, the lter cartridge should be replaced.
3. Put back the cleaned lter cartridge into his case and screw it to the pool.
EN
5.3. Drainage and storage
Drainage
1 Check the stopper on the bottom of the pool and the drain cap.
2 Unscrew the drain cap.
3 Connect the drainage hose.
4 Remove the stopper on the bottom of the pool. Completely drain all water from the
spa pool.
Once empty, the pool can be cleaned with soap and water.
Storage
5 Press the bubbling button to blow out the water inside the jet holes. Unplug the
pump, remove the lter cartridge from the inner wall of the pool.
6 Use a towel to wipe o󰀨 the pool, dry 24 hours.
7 Unscrew the valves to deate the pool.
8 Fold the pool.
It is recommended that store the SPA in its original package in a warm dry place.
5.4. Repair kit
Little holes or puncture can be repaired with the repair kit included and glue reserved to
pool liner.
1. Find the leak.
2. Thoroughly clean the area surrounding the leak.
3. Cut a piece of repair material in round shape, which should be larger than the dam-
aged area.
4. Apply adhesive to the underneath side of the patch and around the area to be re-
paired.
5. Put the patch on the damaged area and press down rmly. Allow 12 hours for repair
to dry. After patch has dried, apply glue around the edges for a complete seal (dry 4
hours).
1
5
2
6
3
7
4
8
Do not return the product to the store
Contact your local after sales service
on www.netspa.eu or POOLSTAR FRANCE
ZA Les pielettes - 13740 LE ROVE - FRANCE
IMPORTANT
Here are some useful tips to help you to diagnose and rectify common sources of
trouble.
Problem Cause Solution
Control panel
screen does not
operate
Check power source
Power failure
Reset the RCD plug / Check if the wiring system is adapted to
the power of the pump unit (1540W)
Call for service if it does not reset
SPA pump does not
heat properly
Temperature set is too low Set to a higher temperature
Filter Cartridge is dirty Clean or Replace the cartridge (see chapter 5.2)
Too low water level Fill water to minimum water level
Heating element defective Call for service
Bubble massage
system does not
work
Pump is overheating Cut o󰀨 the power and wait until the pump has cooled.
Auto shut-down feature (30min) is
activated Press the bubble button to reactivate
Malfunction of the pump unit Call for service if it does not reset
Water ltration does
not work
Filter Cartridge is dirty Clean or Replace the cartridge (see chapter 5.2)
Inlet and outlet blocked Clean the inlet and outlet
Air inside the pump Fill water to minimum water level
Malfunction of the pump unit Call for service if it does not reset
Pump leakage
Adaptor seal improperly Replace the seal in the right position
Water leakage from pump body Check the pump body, call for service
Spa pool leakage Spa pool is torn or punctured Use provided repair kit (see chapter 5.4)
Water is not clean
Insu󰀩cient ltering time Increase the ltering time
Filter Cartridge is dirty Clean or Replace the cartridge (see chapter 5.2)
Pool lled water quality Change the pool water completely
Improper water treatment Refer to the chemical manufacturer’s instructions
6. TROUBLE SHOOTING
6.1. Troubleshooting
!
EN
In case of malfunction, please contact the customer service center NetSpa by connec-
ting to the following address: http://support.netspa.eu
After verifying your information, and an online diagnosis of your spa one of our repre-
sentatives will contact you to provide you indicated the procedure.
If necessary, we will ask you to return the pump unit of your spa for a complete diagno-
sis and repair.
6.2. Return procedure
1) Disconnect the spa
4) Empty the remaining water within
the pump unit.
7) After a complete diagnosis in our
center, you will receive the replace-
ment pump unit.
5) Pack appropriately the pump unit
in its original packaging including your
return authorization.
8) Connect the unit pump to the pool
using the 3 connectors to screw.
Ensure the icons on the pump and the
pool match up
6) Ship the pump unit.
9) Unscrew the caps inside the pool.
Your spa is ready to be used.
2) Do not empty the pool by screwing
the caps inside the pool
3) Unscrew the three connectors from
the pump unit.
The procedure described below is also detailed on the DVD included.
NetSpa products have been inspected and found free of defects prior to leaving the factory.
NetSpa warrants this product against defects in material and workmanship for a period of one
(1) year.
The warranty period begins on the date of purchase and NetSpa requires presentation of the
original proof to purchase to ascertain the date. During the warranty period, NetSpa will either
repair or replace, at its discretion, any defective products. Replacement products or repaired
parts will be warranted for only the unexpired portion of the original warranty.
Shipping cost policy
The return of defect parts to the authorized service center is at the charge of the owner. On
warranty period, the return is at the charge of service center.
Warranty policy
This limited warranty does not apply to any defect resulting from negligence, accident,
misuse, or other reason beyond NetSpa’s reasonable control, included but not limited to:
normal wear and tear, negligence or failure to follow the product instructions, improper or
inadequate maintenance; connection to improper power supply; chemical water damage, loss
of pool water, unauthorized product modication or repair; use for commercial purpose; re,
lightening, ood or other external causes.
● This warranty is valid only in the country of purchase in such countries where NetSpa sells
and services the same model with identical technical specications.
Warranty service outside the country of purchase is limited to the terms and conditions of
the corresponding warranty in the country of service. Where the cost of repairs or replacement
is not covered by this warranty, NetSpa will advise the owners and the cost shall be charged
to the owner.
This warranty only applies to the original purchaser and terminates upon any transfer of
ownership.
All repairs of which warranty claims are made must be pre-authorized by a NetSpa service
center.
All the authorized selling dealer is responsible for all in-eld service work carried out on your
NetSpa product. NetSpa will not be liable for results of cost of workmanship from unautho-
rized service person.
Warranty registration
To validate your warranty, please register your product on our website NetSpa www.netspa.
eu. It is essential that all informations including customer name, date of purchase, serial num-
ber, spa model are indicated. Without these informations the warranty will be invalid.
7. WARRANTY
7.1. Warranty
EN
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Netspa Canyon wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Netspa Canyon

Netspa Canyon Bedienungsanleitung - Holländisch - 12 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info