Bedienungsanleitung Newpol XD900IXDG (Seite 14 von 80) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

22060

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Options

(Note: the various options must be selected before initiating the wash cycle)

• Delayed start : time delays for the initiation of the wash cycle can be set ranging from 1 to 16 hours.

On the display, the delay period that was selected will be shown. The LED display will be blinking during the

entire delay period.

The selection of this setting option is confirmed when the number of the pre -selected programme appears

on the display.

• Half load : when choosing this wash cycle option, the following indication will appear on the display:

(¯=wash superior basket,_=wash inferior basket). The corresponding LED indication will be illuminated.

The selection of this setting option is confirmed when the number of the pre-selected programme appears

on the display.

• Pre-wash cancel : This option is only available for programmes that include a pre-wash.

When pressing the button, the corresponding LED indication will be illuminated.

The selection of this setting option is confirmed when the number of the pre-selected programme appears

on the display.

• Drying : this programme option is carried out automatically by the programmes in whose cycle it is

included (see programme table). To modify the dryer setting, the drying button must be pressed before

initiating the chosen programme. On the display, the following information will appear: AO = no drying; A1=

Drying 20’; A2 = Drying 35’; A3 = Drying 45’.

The corresponding LED indication will be illuminated.

The selection of this setting option is confirmed when the number of the pre -selected programme appears

on the display.

• Note: In the models without the drying ventilator, this option is to be considered as waiting time at the end

of the cycle.

• Description of Start/Stop/Pause button

• It initiates the wash programme cycle (the buzzer sound indicates that the cycle has started).

• When you turn on the machine, using the ON/OFF button, the display indicates the number of the last

program that has been carried out. In cases where the previous program has not yet finished, the display

will flash the number of this program. In order to re-start it you must simply press the “START” button ,

the remaining time that is necessary in order to finish the cycle will appear automatically on the display.

(Situations such as this will occur each time that you open the machine when it is carrying out a program).

• If pressed during the wash for less than 5” the machine will pause, the number of the program will be seen

flashing on the display, (in this case it is possible to add or remove dishes etc.)

In order to proceed with the washing program, close the door and press the button again.

• Programme settings by mistake (change programme)

• Reset by using the start/stop/pause button : keep the button pressed until the buzzer stops beeping (it

produces a series of beeps).

• Repeat the select programme operation.

Note: If the programme has been initiated and has run beyond the water fill phase, the display indicates

“ “, Then, the appliance will discharge all water, and (after a prolonged buzzer sound) the display will

indicate the pre-selected programme setting.

Now, the appliance is ready for a new setting.

• Note: Once you have opened the door, always press the Start button in order to restart the dishwasher.

• Activation / Elimination of the buzzer

b0 = Buzzer DEACTIVATED

b1 = Buzzer ACTIVATED

In order to access the setting of the BUZZER, keep the PROGRAM button pressed down when you

turn on the machine. The current setting “b1” will be visualised on the Display. In order to change this

setting, press the same button until you have selected the status of the buzzer that you desire. Wait for

approximately 6 seconds, without changing your choice, following this, the sound of the BUZZER will confirm

that the setting has been memorised.

• End of cycle

Once the washing cycle is finished , the program number will appear lit up and still on the display, if it

is flashing wait for the end of the cycle.

• Checking the functions

During the washing phase it is possible to visualise the various functions in the following manner:

By pressing the program selection button , the number of the pre-set program will be visualised on the

display.

By pressing the half load button , the upper or lower washing area will be seen.

By pressing the drying button , the level of drying will be seen.

Stop

After the wash cycle, the dishwasher stops automatically, then unit will emit a long buzz to indicate the end of

the wahing cycle. To turn it off, press the button on/off . After each wash cycle, the water faucet must be

closed to insulate the appliance from the water supply system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Newpol XD900IXDG Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info