Bedienungsanleitung Nextbase 202 in-car cam (Seite 10 von 24) (Englisch)

620463

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

IN VEHICLE INSTALLATION (CONTD.)

Please read and follow the notes below for the safe operation of your iN-CAR CAM within your

vehicle.

As per the installation instructions, it is advised to install the iN-CAR CAM so it does NOT obstruct

the drivers view of the road, preferably on the passenger side of the vehicle and behind the rear

view mirror.

Whilst the iN-CAR CAM clearly needs to view through the windscreen in an area swept by the

windscreen wipers, the iN-CAR CAM should be installed so as not to intrude significantly within the

wiped area. A 40mm intrusion into the wiped area is the maximum recommended.

Do NOT mount the iN-CAR CAM in front of the driver, as depicted by the red area in the above

illustration.

When installing the iN-CAR CAM in a vehicle, always place the device securely against the

windscreen and where possible conceal the power cable under trim. Make sure that the iN-CAR

CAM power cable does not interfere with the drivers operating controls, such as the steering wheel,

pedals or gear levers.

Do NOT mount the iN-CAR CAM in a position that would obscure any mirrors, in front of an airbag

field of deployment or any other safety equipment.

Clean the windscreen at the point of location, prior to fitting the iN-CAR CAM, also, applying some

moisture to the suction cup may be beneficial, to ensure absolute adhesion.

It is recommended NOT to operate the iN-CAR CAM whilst driving. The automatic Start-Stop

technology incorporated within the device negates any need to operate the controls whilst driving.

Adjust any settings or review recordings whilst stationery, not whilst driving.

After the preliminary SETUP has been carried out upon the iN-CAR CAM, adjust the Screen Saver

setting to 10 Seconds, this will blank the screen automatically shortly after starting the vehicle and

the screen will NOT be a distraction in any way to the driver.

Note:

- It is recommended to position your iN-CAR CAM on the passenger side of the car, behind the rear

view mirror, as shown above. Whilst the camera needs to be located in a position within the wiper

swept area, do not allow the camera to obstruct your vision of the road ahead. Recommended

position is no more than 40mm within the wiper swept area.

- To reduce the risk of theft, remove the unit and the mount from your vehicle, or position out of

sight, before leaving your vehicle unattended.

- In vehicles where the 12V / 24V output remains on when ignition is turned off please disconnect

the device when not in use.

- The supplied car adaptor has a 4m long cable to allow cable to placed neatly under trims within the

vehicle.

- First time use of the device will require the Time and Date to be set. See Page 17 for details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nextbase 202 in-car cam Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nextbase 202 in-car cam

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info