Bedienungsanleitung Nextbase 4063 in-car-cam (Seite 7 von 33) (Englisch)

698675

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

INSTALLATION

1. pen dust cover and i

gold contacts facing the back of the device . Push the memory card until it clicks into place and close dust cover.

Do not remove or insert the memory card when the iN-CAR CAM is turned on. This may damage the memory card.

2. Attach the device to the supplied windscreen mount, taking care the locking tab has clicked firmly into place.

3. Remove the protective plastic film from the suction pad. Select required position for the windscreen mount and

clean windscreen with a dry / clean cloth to achieve good contact between the glass and mount. While holding the

suction cup onto the glass push the locking lever upwards to secure the mount to the windscreen.

Please ensure that once mounted the iN-CAR CAM is located within the area of the vehicles windscreen wipers to

maintain a clear view during rainfall.

. The angle and position of the iN-CAR CAM can be adjusted by loosening the locking clamp and moving as required,

remembering to re-tighten the clamp.

. Connect the car adaptor to mini-USB socket of the iN-CAR CAM and then plug the supplied car adaptor into the

12-2 Vdc outlet of your vehicle. The device will automatically power on and start recording once power is available.

In some vehicles this will be when connections are made, for others the device will power on once the ignition has

been turned on.

N TE:

our iNCAR-CAM is shipped with the Screen Saver function set to Default FF. This is for ease of initial setup.

nce setup is complete, the screen saver should be set to 1 seconds, in order to blank the screen completely

whilst driving. This avoids any potential distraction and may be a legal requirement in some countries.

It is recommended to position your iNCAR-CAM on the passenger side of the car, behind the rear view mirror, as

shown above. Whilst the camera needs to be located in a position within the wiper swept area, do not allow the

camera to obstruct your vision of the road ahead. Recommended position is no more than 0mm within the wiper

swept area. Do N T mount the camera directly in front of the driver.

Do not place the iN-CAR CAM in such a way that it may interfere with the deployment of air bags or other safety

equipment.

Do not operate the unit while driving.

To reduce the risk of theft, remove the unit and the mount from your vehicle, or position out of sight, before

leaving your vehicle unattended.

In vehicles where the 12V / 2 V output remains on when ignition is turned off please disconnect the device when

not in use.

The supplied car adaptor has a m long cable to allow cable to placed neatly within the vehicle.

First time use of the device will require the Time and Date to be set. See Page 10 for details.

nsert a suitable memory card in to the device, taking care to follow correct orientation markings

The above diagram is f .or illustration purposes only

12-2 DC

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nextbase 4063 in-car-cam Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info