Bedienungsanleitung Niagara B264 Standalone Encoder (Seite 111 von 120) (Englisch)

641176

111

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

111

The configuration parameters are:

 Device Name: This field controls the top-level name of the device in the Dashboard tree.

It defaults to “Standalone Encoder”. Changes to this field take effect immediately.

 IP Configuration: This field selects the control port IP configuration mode, as follows:

o Static IP: This option selects a static IP configuration, specified by the IP

Address, Subnet Mask, Default Gateway and DNS Server fields.

o DHCP: This option selects control port IP address configuration by DHCP. If

this option is selected, the IP Address, Subnet Mask, Default Gateway and DNS

Server fields are not shown.

 IP Address: This field is only shown if IP Configuration is set to Static IP. Enter the

desired control port IP address. You cannot set this IP address to the same value as the

Ethernet1/Ethernet2 IP addresses (see the Network Tab section earlier in this document).

 Subnet Mask: This field is only shown if IP Configuration is set to Static IP. Enter the

desired control port subnet mask.

 Default Gateway: This field is only shown if IP Configuration is set to Static IP.

Enter the desired control port default gateway.

 DNS Server: This field is only shown if IP Configuration is set to Static IP. Enter the

desired DNS Server IP address. Note that DNS is only used for RTMP output. This field

can be left at 0.0.0.0 if RTMP is not used. If you wish to configure more than one DNS

server, you can enter them in the Network Configuration DNS Tab. If you configure

DNS servers here and in the Network Configuration, the server specified here will be

contacted first.

 NTP Server: If you want the unit to be NTP-synchronized (for logging purposes), enter

the IP address of an accessible NTP server in this field. If you do not need NTP, you can

leave this field at 0.0.0.0. If your B264 has access to the Internet through the control port,

you can point it to one of the public NTP servers for your region. You can find more

details on this link:

http://psp2.ntp.org/bin/view/Servers/WebHome

 Apply/Cancel: Use these buttons to apply or cancel the changes to the control port IP

configuration. Note that if you change the IP address, DashBoard may lose contact with

the B264. The IP Address, Subnet Mask and Default Gateway entries will be checked for

consistency and will be rejected if invalid.

Control Port Statistics Tab

The Control Port statistics screen is depicted below. It contains the current settings for the

control port. If you have configured the unit for DHCP, it will include the current IP Address,

Subnet Mask, Default Gateway and the first DNS server obtained from the DHCP server. It also

includes the link state for the individual control Ethernet ports.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Niagara B264 Standalone Encoder Seite 111

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Niagara B264 Standalone Encoder

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info