Bedienungsanleitung Nikkei NTT05U (Seite 5 von 12) (Englisch)

612764

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

1. Remove the main unit with the packing from the box and remove the packing.

2. Set the 45-rpm adaptor on the main unit.

3. Set the turntable platter onto the center spindle.

4. Set the slip mat on the platter.

5. Installation of cartridge:

When installing a cartridge, refer to the operating instructions of that cartridge.

During installation, attach the stylus protector to guard the stylus tip from damage.

(a) Connect the lead wires to the cartridge terminals. The terminals of most cartridges are color-coded.

Connect each lead wire to the terminal of the same color.

White (L+)…………………………… Left channel+

Blue (L-) ..................... …………… Left channel-

Red (R+) ......................………….. Right channel+

Green (R-) ................………………. Right channel-

(b) Install the cartridge to the headshell and tighten it with screws provided with the cartridge.

6. Insert the headshell into the front end of the tonearm, then turn the lock nut counterclockwise with the

headshell firmly held horizontally.

7. Slide counterweight onto tonearm. Twist it lightly and it will screw onto the rear shaft of the tonearm.

8. Adjustment of horizontal “zero” balance and stylus pressure:

(a) Remove the stylus protector from the headshell, do not touch the stylus tip during the adjustment.

(b) Set the cueing lever to the lowered position.

(d) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely).

(e) Refasten the tonearm with the tonearm clamp.

(f) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the

number "0" of the ring into alignment with the center line on the tonearm rear shaft.

(g) Rotate the counterweight including the stylus-pressure ring counterclockwise until the scale shows the

value corresponding to the pressure of the stylus used. Should you use a separate Stylus, please

follow the manufacturer’s instructions.

9. Set the anti-skating control knob to the same value as the stylus pressure.

10. Install the

transparent

dust cover to the main unit’s dust cover hinges.

• Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance.

• Do not place the unit in a location where there is high humidity or a lot of dust.

• Cartridge may pick up slight sound pressures or vibrations of the speakers coming along the floor or through

the air resulting in feedback or “howling” sound. Find a location which is very stable and vibration free.

•

The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the

main body horizontally.

ASSEMBLY

PLACEMENT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikkei NTT05U Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nikkei NTT05U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info